超快冷处理低合金Q345B钢的折弯开裂失效分析与对策

doi:10.13251/j.issn.0254-6051.2020.01.046

摘要/Abstract

摘要： 利用扫描电镜对超快冷工艺生产的Q345B钢弯曲失效开裂的断口形貌、显微组织和钢中的夹杂物进行了分析。结果表明,Q345B钢中存在超标的大尺寸夹杂物诱发了弯曲变形过程中裂纹的萌生,而超快冷工艺产生的网状渗碳体和粒状贝氏体硬相组织降低了Q345B钢的塑性和韧性,促进了裂纹的扩展。通过延长LF工序精炼时间和控制超快冷工艺冷却速度及提高终冷温度,使钢中夹杂物尺寸大大降低,显微组织转变为铁素体和珠光体组织,从而提高了Q345B抗弯曲性能。

关键词: Q345B钢, 超快冷, 折弯开裂, 网状渗碳体, 夹杂物

Abstract: Fracture morphology, microstructure and inclusions of bending cracking of Q345B steel treated by ultra-fast cooling process were systematically analyzed by scanning electron microscopy. The results show that a lot of large-size inclusions are observed in the Q345B steel which causes the crack initiation during bending deformation. However, the hard-phase microstructure including network cementite and granular bainite are produced during ultra-fast cooling process reduces the plasticity and toughness of the Q345B steel and promotes further the crack propagation. By extending refining time of LF process, controlling ultra-fast cooling rate and increasing the final cooling temperature, the inclusion size in the steel is greatly reduced, and the microstructure is transformed into ferrite and pearlite, thus the bending resistance of the Q345B steel is improved greatly.

Key words: Q345B steel, ultra-fast cooling, bending cracking, network cementite, inclusions

中图分类号:

TG115

喻春明, 张继明. 超快冷处理低合金Q345B钢的折弯开裂失效分析与对策[J]. 金属热处理, 2020, 45(1): 239-244.

Yu Chunming, Zhang Jiming. Failure analysis and improvement of bending cracking of low alloy Q345B steel treated by ultra-fast cooling process[J]. HTM, 2020, 45(1): 239-244.

参考文献

[1]王丙兴, 董福志, 王昭东, 等. 超快冷条件下Mn-Nb-B系低碳贝氏体高强钢组织与性能研究[J]. 材料工程, 2016, 44(7): 26-31.
Wang Bingxing, Dong Fuzhi, Wang Zhaodong, et al. Microstructure and property of Mn-Nb-B low carbon bainite high strength steel under ultra-fast cooling[J]. Journal of Materials Engineering, 2016, 44(7): 26-31.
[2]邹扬, 张苏渊, 顾林豪, 等. 超快冷对高强度Mn-B 钢板组织与性能的影响[J]. 金属热处理, 2014, 39(10): 91-95.
Zou Yang, Zhang Suyuan, Gu Linhao, et al. Influence of ultra-rapid cooling on microstructure and properties of high strength Mn-B steel plate[J]. Heat Treatment of Metals, 2014, 39(10): 91-95.
[3]尹翠兰. 1000 MPa 级热轧双相钢的微观组织及强化机制[J]. 金属热处理, 2016, 41(2): 54-57.
Yin Cuilan. Microstructure and strengthening mechanism of 1000 MPa grade hot-rolled dual-phase steel[J]. Heat Treatment of Metals, 2016, 41(2): 54-57.
[4]Harasawa H, Yasuoka T, Kobayashi H, et al. The development of welding procedures for arctic structures and offshore platforms using TMCP (Thermo-mechanical controlled process) steel plates[C]//Welding for Challenging Environments. Toronto: Welding Institute of Canada, 1986: 85-96.
[5]Nagao A, Ito T, Obinata T. Development of Hiten “JFE-HYD 1100LE” ultra high strength steel plate with high resistance to delayed fracture[J]. JFE Technical Report, 2008, 11: 13-18.
[6]Misra R D K, Nathani H, Hartmann J E, et al. Microstructural evolution in a new 770 MPa hot rolled Nb-Ti microalloyed steel[J]. Materials Science and Engineering A, 2005, 394: 339-352.
[7]王国栋. 新一代TMCP技术的发展[J]. 轧钢, 2012, 29(1): 1-8.
Wang Guodong. Development of a new generation TMCP technology[J]. Steel Rolling, 2012, 29(1): 1-8.
[8]张阔斌, 侯蕾, 王俊, 等. 超快冷技术在唐钢中厚板生产线上的应用[J]. 轧钢, 2018, 35(5): 67-70.
Zhang Kuobin, Hou Lei, Wang Jun, et al. Application of ultra-fast cooling technology on medium plate production line of Tang steel[J]. Steel Rolling, 2018, 35(5): 67-70.
[9]张鹤松, 朱国明, 康永林. 超快冷工艺生产X90 管线钢组织性能与析出行为[J]. 材料热处理学报, 2015, 36(12): 103-109.
Zhang Hesong, Zhu Guoming, Kang Yonglin. Microstructure, properties and precipitation behavior of X90 pipeline steel produced by ultra fast cooling[J]. Transactions of Materials and Heat Treatment, 2015, 36(12): 103-109.
[10]李凡, 衣海龙, 刘振宇, 等. 超快冷工艺下工程机械用550 MPa级钢的组织与性能[J]. 机械工程材料, 2014, 36(4): 34-36.
Li Fan, Yi Hailong, Liu Zhenyu, et al. Effects of ultra fast cooling process on microstructure and properties of 550 MPa steel used for engineering machinery[J]. Materials for Mechanical Engineering, 2014, 36(4): 34-36.
[11]王国栋, 刘振宇. 新一代节约型高性能结构钢的研究现状与进展[J]. 中国材料进展, 2011, 30(12): 12-17.
Wang Guodong, Liu Zhenyu. Current status and progress on the development of cost-saving and high performance structural steels[J]. Materials China, 2011, 30(12): 12-17.
[12]辛学武, 关小军, 张继明. 345 MPa 级钢的柔性制造技术研究[J]. 山东冶金, 2011, 33(5): 82-86.
Xin Xuewu, Guan Xiaojun, Zhang Jiming. Study on flexible manufacturing process for 345 MPa grade low alloy high strength steel[J]. Shandong Metallurgy, 2011, 33(5): 82-86.
[13]孟庆勇, 臧淼, 李思, 等. 超快冷条件下低合金钢板的合金减量化生产工艺实践[J]. 宽厚板, 2016, 22(5): 21-24.
Meng Qingyong, Zang Miao, Li Si, et al. Production process practice of alloy decrement for low alloy steel plate under ultra-fast cooling condition[J]. Wide and Heavy Plate, 2016, 22(5): 21-24.
[14]GB/T 10561—2005, 钢中非金属夹杂物含量的测定标准评级图显微检验法[S].
[15]Zhang J M, Li S X, Yang Z G, et al. Influence of inclusion size on fatigue behavior of high strength steels in the gigacycle fatigue[J]. International Journal of Fatigue, 2007, 29: 765-771.
[16]Atkinson H V, Shi G. Characterization of inclusions in clean steels: A review including the statistics of extremes methods[J]. Progress in Materials Science, 2003, 48: 457-520.
[17]Zhang J M, Ji L K, Bao D J, et al. Gigacycle fatigue behavior of 1800 MPa grade high strength spring steel for automobile light weight[J]. Journal of Iron and Steel Research, International, 2014, 21(6): 614-618.
[18]吴良芹, 任娟. 超快冷工艺对Q390C钢组织与性能的影响[J]. 上海金属, 2013, 35(6): 31-37.
Wu Liangqin, Ren Juan. Effect of ultra fast cooling on microstructure and properties of Q390C steel[J]. Shanghai Metals, 2013, 35(6): 31-37.
[19]王猛, 刘振宇, 李成刚. 轧后超快冷及亚温淬火对5%Ni钢微观组织与低温韧性的影响机理[J]. 金属学报, 2017, 53(8): 947-956.
Wang Meng, Liu Zhenyu, Li Chenggang. Effects of ultra-fast cooling after hot rolling and lamellarizing on microstructure and cryogenic toughness of 5%Ni steel[J]. Acta Metallurgica Sinica, 2017, 53(8): 947-956.