渗碳淬回火工艺对G20CrNi2Mo钢组织与性能的影响

doi:10.13251/j.issn.0254-6051.2020.04.035

金属热处理 ›› 2020, Vol. 45 ›› Issue (4): 166-170.DOI: 10.13251/j.issn.0254-6051.2020.04.035

渗碳淬回火工艺对G20CrNi2Mo钢组织与性能的影响

付明¹, 王智勇²

1. 中国空空导弹研究院, 河南洛阳 471023;
2. 洛阳轴承研究所有限公司, 河南洛阳 471039

收稿日期:2019-10-20 出版日期:2020-04-25 发布日期:2020-05-08
作者简介:付明(1969—),男,研究员,主要从事金属零部件腐蚀与防护技术及三废治理技术研究,E-mail:mingfu691221@sina.com
基金资助:
河南省科技攻关计划(172102210399,122102210059);河南省重点科技攻关项目(152102210074)

Effect of carburizing quenching and tempering process on microstructure and properties of G20CrNi2Mo steel

Fu Ming¹, Wang Zhiyong²

1. China Air Missile Research Institute, Luoyang Henan 471023, China;
2. Luoyang Bearing Research Institute Co., Ltd., Luoyang Henan 471039, China

Received:2019-10-20 Online:2020-04-25 Published:2020-05-08

摘要/Abstract

摘要： 以G20CrNi2Mo渗碳轴承钢为研究对象,通过扫描电镜及光学显微镜分析不同热处理工艺下的组织及硬度差异,并借助摩擦磨损试验机研究其耐磨性能的变化。结果表明,G20CrNi2Mo轴承钢渗碳后经过不同淬火及回火工艺,其硬度和耐磨性能均有了明显提高,其中,二次淬火后的组织为细小的马氏体和均匀细小的颗粒碳化物,以及少量的残留奥氏体;二次淬火后经过回火处理,200 ℃低温回火的组织性能最优,组织为回火马氏体,其硬度值为62.3 HRC,磨损量为12.9 g。

关键词: G20CrNi2Mo钢, 淬火, 回火, 组织, 硬度, 耐磨性能

Abstract: The variety of hardness and microstructure for G20CrNi2Mo steel after different heat treatment was analyzed by means of the optical microscopy (OM) and scanning electron microscope (SEM). And the wear resistance for the steel was studied by the friction abrasion testing machine. The results show that the hardness and wear resistance of G20CrNi2Mo steel are improved obviously after carburizing and quenching and tempering. The microstructure is fine martensite, grain carbide, and a small amount of residual austenite after double quenching. After the second quenching and tempering, the microstructure and properties of low temperature tempering at 200 ℃ are the best, and the microstructure is tempered martensite, with hardness value and wear loss of 62.3 HRC and 12.9 g, respectively.

Key words: G20CrNi2Mo steel, quenching, tempering, microstructure, hardness, wear resistance

中图分类号:

TG156

付明, 王智勇. 渗碳淬回火工艺对G20CrNi2Mo钢组织与性能的影响[J]. 金属热处理, 2020, 45(4): 166-170.

Fu Ming, Wang Zhiyong. Effect of carburizing quenching and tempering process on microstructure and properties of G20CrNi2Mo steel[J]. Heat Treatment of Metals, 2020, 45(4): 166-170.

参考文献

[1]张增岐, 刘耀中, 樊志强. 贝氏体等温淬火及其在轴承上的应用[J]. 金属热处理, 2002, 23(1): 57-60.
Zhang Zengqi, Liu Yaozhong, Fan Zhiqiang. Bainite isothermal quenching and its application in bearing[J]. Heat Treatment of Metals, 2002, 23(1): 57-60.
[2]赵国防, 杨卯生, 刘东雨, 等. 高性能渗碳轴承钢的组织与性能[J]. 钢铁研究学报, 2011, 23(11): 34-40.
Zhao Guofang, Yang Maosheng, Liu Dongyu, et al. Microstructure and properties of high performance carburizing bearing steel[J]. Journal of Iron and Steel Research, 2011, 23(11): 34-40.
[3]李华杰, 武会宾, 唐荻, 等. GCr15 轴承钢的再结晶规律研究[J]. 热加工工艺, 2009, 38(8): 7-8.
Li Huajie, Wu Huibin, Tang Di, et al. Study on recrystallization rule of GCr15 bearing steel[J]. Hot Working Technology, 2009, 38(8): 7-8.
[4]Kato Y, Masuda T, Kawakami K, et al. Recent improvements in clean liness in high carbon chromium bearing steel[J]. ISIJ International (Japan), 1996, 36: 89-92.
[5]江涛, 梅亚莉, 雷建中, 等. 高碳铬轴承钢贝氏体等温淬火工艺的应用[J]. 轴承, 1998(3): 15-17.
Jiang Tao, Mei Yali, Lei Jianzhong, et al. The application of high carbon chromium bearing steel bainite isothermal quenching process[J]. Bearing, 1998(3): 15-17.
[6]封珂, 朱百智, 郭祺龙. 18CrNiMo7-6和20CrNi2Mo钢渗碳工艺参数优化与应用[J]. 金属热处理, 2010, 35(6): 63-66.
Feng Ke, Zhu Baizhi, Guo Qilong. Optimization and application of carburizing process parameters for 18CrNiMo7-6 and 20CrNi2Mo steels[J]. Heat Treatment of Metals, 2010, 35(6): 63-66.
[7]李中友. G20CrNi2MoA渗碳轴承钢生产工艺的探讨[J]. 特钢技术, 2010, 16(3): 10-14.
Li Zhongyou. A study on production process of G20CrNi2MoA carburizing bearing steel[J]. Special Steel Technology, 2010, 16(3): 10-14.
[8]周立新, 丁磊, 苏春阳, 等. 惰性气体保护5 t电渣炉重熔铁路用G20CrNi2MoA渗碳轴承钢[J]. 特殊钢, 2012, 33(5): 25-28.
Zhou Lixin, Ding Lei, Su Chunyang, et al. Carburized bearing steel G20CrNi2MoA for railway remelted by an inert gas sllielding atmosphere 5 t electroslag remelting furnace[J]. Special Steel, 2012, 33(5): 25-28.
[9]沈伟毅, 张中文, 郝亚硕. G20CrNi2MoA钢代替G20Cr2Ni4A钢制造轴承滚子的热处理试验[J]. 金属热处理, 2009, 34(11): 80-82.
Shen Weiyi, Zhang Zhongwen, Hao Yashuo. Heat treatment of G20CrNi2MoA steel for bearing roller in stead of G20Cr2Ni4A steel[J]. Heat Treatment of Metals, 2009, 34(11): 80-82.
[10]黄宇彬. G20CrNi2MoA 渗碳轴承钢单支臂生产工艺实践[J]. 大型铸锻件, 2014(4): 36-37.
Huang Yubin. Technology practice for single supporting arm production of G20CrNi2MoA carburized bearing steel[J]. Heavy Casting and Forging, 2014(4): 36-37.
[11]李淑镜, 张岭, 王新伟. 1G20CrNi2MoA钢制轴承套圈的热处理工艺[J]. 哈尔滨轴承, 2012, 33(4): 42-44.
Li Shujing, Zhang Ling, Wang Xinwei. Technology of heat treatment for bearing ring manufactured with G20CrNi2MoA steel[J]. Journal of Harbin Bearing, 2012, 33(4): 42-44.
[12]Hermann Vetters, Juan Dong, Hubert Bomas, et al. Microstructure and fatigue strength of the roller-bearing steel 100Cr6 after twostep bainitisation and combined bainitic-martensitic heat treatment[J]. International Heat Treatment and Surface Engineering, 2006, 97(10): 1432-1435.
[13]虞明全. 轴承钢钢种系列的发展状况[J]. 上海金属, 2008, 30(3): 49-54.
Yu Mingquan. The development status of bearing steel and its grades series[J]. Shanghai Metals, 2008, 30(3): 49-54.
[14]汪建利, 李超. GCr15 钢贝氏体-马氏体复合组织的力学性能[J]. 热加工工艺, 1990(5): 5-9.
Wang Jianli, Li Chao. The mechanical properties of GCr15 steel with duplex structure of martensite and bainite[J]. Hot Working Technology, 1990(5): 5-9.
[15]胡光立, 谢希文. 钢的热处理[M]. 西安: 西北工业大学出版社, 1993: 203-212.
[16]王铀, 高彩桥, 雷廷权, 等. GCr15钢和T8钢的原始组织硬度与耐磨性[J]. 钢铁, 1991, 26(8): 50-53.
Wang You, Gao Caiqiao, Lei Tingquan, et al. Original structural hardness and wear resistance of steels GCr15 and T8[J]. Iron and Steel, 1991, 26(8): 50-53.
[17]冷艳, 黄维刚. 热处理工艺对Cr12MoV钢组织、硬度及耐磨性的影响[J]. 四川冶金, 2010, 32(1): 8-11.
Leng Yan, Huang Weigang. Effect of heat treatment process on microstructure, hardness and wear resistance of Cr12MoV steel[J]. Sichuan Metallurgy, 2010, 32(1): 8-11.
[18]米振莉, 张小垒, 李志超, 等. 热处理工艺对高碳铬轴承钢组织和性能的影响[J]. 材料热处理学报, 2015, 36(7): 119-120.
Mi Zhenli, Zhang Xiaolei, Li Zhichao, et al. Effect of heat treatment process on microstructure and properties of a high carbon chromium bearing steel[J]. Transactions of Materials and Heat Treatment, 2015, 36(7): 119-120.

渗碳淬回火工艺对G20CrNi2Mo钢组织与性能的影响

Effect of carburizing quenching and tempering process on microstructure and properties of G20CrNi2Mo steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	王玉岱, 刘洋, 朱言言, 田象军, 程序, 冉先喆, 钱婷婷. 热处理对复合制造AerMet100超高强度钢组织均匀性与拉伸性能的影响[J]. 金属热处理, 2022, 47(4): 1-9.
[2]	张子延, 陈君, 陈晓亚, 李全安, 刘建鑫. 固溶时效处理对Mg-4Sm-3Gd-0.5Zr合金显微组织和耐蚀性能的影响[J]. 金属热处理, 2022, 47(4): 10-16.
[3]	梁恩溥, 徐乐, 杨勇, 王毛球. 添加Al、Cu对40CrNi3MoV钢组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 17-23.
[4]	祁晓亮, 李岩, 定巍, 赵增武. 含Al中锰TRIP钢原始组织对临界退火后组织与力学性能的影响[J]. 金属热处理, 2022, 47(4): 24-29.
[5]	陈保安, 张静媛, 祝志祥, 韩钰, 潘学东, 张磊, 陈素红. 化学成分对高强Al-Mg-Si合金组织和性能的影响[J]. 金属热处理, 2022, 47(4): 30-38.
[6]	陈东俊, 李广阳, 刘刚. 时效处理对AlSi9Cu3压铸铝合金组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 53-56.
[7]	陈连生, 张露友, 田亚强, 杨子旋, 李红斌, 潘红波, 魏英立. 低碳高强舰船用钢的CCT曲线及其组织性能[J]. 金属热处理, 2022, 47(4): 63-68.
[8]	贾昌远, 霍元明, 何涛, 霍存龙, 刘克然. 40CrNiMo钢高温拉伸变形行为和组织演变规律[J]. 金属热处理, 2022, 47(4): 69-74.
[9]	王云龙, 余伟, 张昳, 史佳新, 李明辉. 奥氏体化温度对贝氏体钢等温转变及力学性能的影响[J]. 金属热处理, 2022, 47(4): 80-85.
[10]	刘丽艳, 毕文珍, 韦习成. Mn元素对热冲压钢镀锌层组织演变的影响[J]. 金属热处理, 2022, 47(4): 93-99.
[11]	付锡彬, 陈子豪, 张可, 赵时雨, 孙新军, 朱正海, 梁小凯, 雍岐龙. 淬火温度对高Ti低合金耐磨钢组织及力学性能的影响[J]. 金属热处理, 2022, 47(4): 122-127.
[12]	宿鹏吉, 麻永林, 董丽丽, 杨雪峰. 磁场预退火处理对CGO钢组织与织构的影响[J]. 金属热处理, 2022, 47(4): 128-132.
[13]	李立, 曾艳, 吴晓春. 4Cr5Mo2VCo钢的热处理工艺优化[J]. 金属热处理, 2022, 47(4): 133-140.
[14]	吕杰晟, 宋志刚, 何建国, 丰涵, 郑文杰, 朱玉亮. S32205双相不锈钢冷轧退火组织转变及强塑化机理分析[J]. 金属热处理, 2022, 47(4): 141-145.
[15]	王琪, 吴光亮. 回火温度对1100 MPa级高强钢组织与性能的影响[J]. 金属热处理, 2022, 47(4): 146-150.