强变形工艺对2519A铝合金组织与性能的影响

doi:10.13251/j.issn.0254-6051.2020.05.037

金属热处理 ›› 2020, Vol. 45 ›› Issue (5): 187-191.DOI: 10.13251/j.issn.0254-6051.2020.05.037

强变形工艺对2519A铝合金组织与性能的影响

叶志飞, 孙大翔, 周鹏, 邝宏聪, 肖永通

广东省工业分析检测中心, 广东广州 510650

收稿日期:2019-10-16 出版日期:2020-05-25 发布日期:2020-09-02
通讯作者: 孙大翔,工程师,博士,E-mail:18802081724@163.com
作者简介:叶志飞(1973—),女,工程师,主要研究方向为金属材料性能检测与评价,E-mail:951161366@qq.com。
基金资助:
广东省科学院发展专项资金(2018GDASCX-0954,2018GDASCX-0114)

Effect of severe plastic deformation on microstructure and mechanical properties of 2519A aluminum alloy

Ye Zhifei, Sun Daxiang, Zhou Peng, Kuang Hongcong, Xiao Yongtong

Guangdong Industrial Analysis and Testing Center, Guangzhou Guangdong 510650, China

Received:2019-10-16 Online:2020-05-25 Published:2020-09-02

摘要/Abstract

摘要： 通过硬度测试、拉伸性能测试、透射电镜观察等分析手段研究了不同强变形工艺下2519A铝合金的力学性能与微观组织。结果表明,经50%的冷轧变形和165 ℃人工时效后,2519A合金的力学性能明显提高,其抗拉强度、屈服强度和伸长率分别为522 MPa、468 MPa和8.5%。而在冷变形前添加165 ℃×2 h预时效处理,合金的力学性能进一步提高,其抗拉强度、屈服强度和伸长率分别达到535 MPa、497 MPa和8%。预时效处理可以提高合金中θ′相的密度,使析出相分布更加均匀,有助于提高合金的力学性能。

关键词: 2519A铝合金, 强变形, 预时效, θ′析出相, 力学性能

Abstract: Microstructures and mechanical properties of 2519A aluminum alloy after different severe plastic deformation processes were investigated by means of hardness test, tensile test, and transmission electron microscopy (TEM). The results show that after 50% cold rolling reduction and artificial aging at 165 ℃, the tensile strength, yield strength and elongation of the 2519A alloy are 522 MPa, 468 MPa, 8.5%, respectively. And adding 165 ℃×2 h pre-aging before cold rolling, the mechanical properties are further improved, and the tensile strength, yield strength and elongation of the alloy are 535 MPa, 497 MPa, 8%, respectively. Pre-aging treatment can increase the density of θ′ precipitates in the 2519A alloy and make them more uniformly distributed, which is helpful to improve the mechanical properties of the alloy.

Key words: 2519A aluminum alloy, severe plastic deformation, pre-aging, θ′ precipitates, mechanical properties

中图分类号:

TG146

叶志飞, 孙大翔, 周鹏, 邝宏聪, 肖永通. 强变形工艺对2519A铝合金组织与性能的影响[J]. 金属热处理, 2020, 45(5): 187-191.

Ye Zhifei, Sun Daxiang, Zhou Peng, Kuang Hongcong, Xiao Yongtong. Effect of severe plastic deformation on microstructure and mechanical properties of 2519A aluminum alloy[J]. Heat Treatment of Metals, 2020, 45(5): 187-191.

参考文献

[1]Fisher J J, Kramer L S, Pickens J R. Aluminum alloy 2519 in military vehicles[J]. Advanced Materials and Processes, 2002, 160(9): 43-46.
[2]Hamilton B C, Saxena A. Transient crack growth behavior in aluminum alloys C415-T8 and 2519-T87[J]. Engineering Fracture Mechanics, 1999, 62(1): 1-22.
[3]李慧中, 张新明, 陈明安, 等. 热处理制度对2519A合金的晶间腐蚀性能的影响[J]. 材料热处理学报, 2005, 26(1): 20-23.
Li Huizhong, Zhang Xinming, Chen Ming'an, et al. Effect of heat treatment on microstructure, tensile strength and intergranular corrosion of 2519 aluminum alloy[J]. Transactions of Materials and Heat Treatment, 2005, 26(1): 20-23.
[4]陈险锋, 彭大署, 张辉, 等. 热处理制度对2519铝合金板材力学性能和应力腐蚀敏感性的影响[J]. 中国有色金属学报, 2003, 13(4): 934-938.
Chen Xianfeng, Peng Dashu, Zhang Hui, et al. Influence of heat treatment on mechanical properties and stress corrosion sensitivity of 2519 aluminum alloy plate[J]. The Chinese Journal of Nonferrous Metals, 2003, 13(4): 934-938.
[5]李慧中, 梁萧鹏, 陈明安, 等. 冷轧变形量对2519铝合金组织与力学性能的影响[J]. 材料热处理学报, 2008, 29(2): 86-89.
Li Huizhong, Liang Xiaopeng, Chen Ming'an, et al. Effect of cold rolling reduction on microstructure and mechanical property of 2519 aluminum alloy[J]. Transactions of Materials and Heat Treatment, 2008, 29(2): 86-89.
[6]李慧中, 张新明, 陈明安, 等. 预变形对2519铝合金组织与力学性能的影响[J]. 中国有色金属学报, 2004, 14(12): 1990-1994.
Li Huizhong, Zhang Xinming, Chen Ming'an, et al. Effect of pre-deformation on microstructures and mechanical properties of 2519 aluminum alloy[J]. The Chinese Journal of Nonferrous Metals, 2004, 14(12): 1990-1994.
[7]张新明, 刘玲, 贾寓真. 拉伸与轧制预变形对2519A铝合金组织与力学性能的影响[J]. 中国有色金属学报, 2010, 20(6): 1088-1094.
Zhang Xinming, Liu Ling, Jia Yuzhen. Effects of stretching and rolling pre-deformation on microstructures and mechanical properties of 2519A aluminum alloy[J]. The Chinese Journal of Nonferrous Metals, 2010, 20(6): 1088-1094.
[8]李玉乾, 叶凌英, 张新明, 等. Cr和Yb复合添加对2519A铝合金组织和力学性能的影响[J]. 中南大学学报(自然科学版), 2014, 45(7): 2182-2186.
Li Yuqian, Ye Lingying, Zhang Xinming, et al. Effects of Cr and Yb additions on microstructures and mechanical properties of 2519A aluminum alloy[J]. Journal of Central South University (Science and Technology), 2014, 45(7): 2182-2186.
[9]董宇, 叶凌英, 孙大翔, 等. 预变形量对2519A-T9I6铝合金力学性能和组织的影响[J]. 中国有色金属学报, 2017, 27(12): 2434-2442.
Dong Yu, Ye Lingying, Sun Daxiang, et al. Effects of pre-deformation on microstructure and mechanical properties of 2519A-T9I6 aluminum alloy[J]. The Chinese Journal of Nonferrous Metals, 2017, 27(12): 2434-2442.
[10]孙大翔, 顾刚, 叶凌英, 等. 冷变形与再时效处理对 2519A-T87 铝合金板材力学性能和微观组织的影响[J]. 中南大学学报(自然科学版), 2014, 45(12): 4145-4151.
Sun Daxiang, Gu Gang, Ye Lingying, et al. Effect of cold deformation and reaging on microstructures and mechanical properties of 2519A-T87 alloy plate[J]. Journal of Central South University (Science and Technology), 2014, 45(12): 4145-4151.
[11]Liu Y, Zhang X M, Liu B, et al. Effect of pre-rolling reduction on intergranular corrosion of aluminum alloy 2519A[J]. Materials Science Forum, 2007, 546-549: 1117-1122.
[12]Li H Z, Zhang X M, Chen M A, et al. Effect of pre-deformation on the stress corrosion cracking susceptibility of aluminum alloy 2519[J]. Rare Metals, 2007, 26(4): 385-390.
[13]Zhang X M, Liu L, Ye L Y, et al. Effect of pre-deformation of rolling combined with stretching on stress corrosion of aluminum alloy 2519A plate[J]. Transactions of Nonferrous Metals Society of China, 2012, 22(1): 8-15.
[14]Zhang X M, Gao Z G, Zhao Y S. Effects of short aging on thickening anisotropy of θ' precipitate and mechanical properties of severe cold-rolled 2519A aluminum alloy plate[J]. Journal of Materials Science, 2009, 45(5): 1401-1405.
[15]Kang S B, Lim C Y, Kim H W, et al. Microstructure evolution and hardening behavior of 2024 aluminum alloy processed by the severe plastic deformation[J]. Materials Science Forum, 2002, 396-402(2): 1163-1168.
[16]Murayama M, Horita Z, Hono K. Microstructure of two-phase Al-1.7at%Cu alloy deformed by equal-channel angular pressing[J]. Acta Materialia, 2001, 49(1): 21-29.

强变形工艺对2519A铝合金组织与性能的影响

Effect of severe plastic deformation on microstructure and mechanical properties of 2519A aluminum alloy

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	梁恩溥, 徐乐, 杨勇, 王毛球. 添加Al、Cu对40CrNi3MoV钢组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 17-23.
[2]	祁晓亮, 李岩, 定巍, 赵增武. 含Al中锰TRIP钢原始组织对临界退火后组织与力学性能的影响[J]. 金属热处理, 2022, 47(4): 24-29.
[3]	陈保安, 张静媛, 祝志祥, 韩钰, 潘学东, 张磊, 陈素红. 化学成分对高强Al-Mg-Si合金组织和性能的影响[J]. 金属热处理, 2022, 47(4): 30-38.
[4]	陈连生, 张露友, 田亚强, 杨子旋, 李红斌, 潘红波, 魏英立. 低碳高强舰船用钢的CCT曲线及其组织性能[J]. 金属热处理, 2022, 47(4): 63-68.
[5]	王云龙, 余伟, 张昳, 史佳新, 李明辉. 奥氏体化温度对贝氏体钢等温转变及力学性能的影响[J]. 金属热处理, 2022, 47(4): 80-85.
[6]	骆再斌, 范子泽, 彭振. 轻质高熵合金的研究进展[J]. 金属热处理, 2022, 47(4): 100-107.
[7]	吕杰晟, 宋志刚, 何建国, 丰涵, 郑文杰, 朱玉亮. S32205双相不锈钢冷轧退火组织转变及强塑化机理分析[J]. 金属热处理, 2022, 47(4): 141-145.
[8]	王琪, 吴光亮. 回火温度对1100 MPa级高强钢组织与性能的影响[J]. 金属热处理, 2022, 47(4): 146-150.
[9]	张骥俊, 邢彦锋, 曹菊勇. 超声振动对CMT电弧增材制造铝合金组织与性能的影响[J]. 金属热处理, 2022, 47(4): 159-164.
[10]	刘文彬, 乔龙阳, 潘新宇, 程格, 李爱娜, 裴新军. 淬火温度对刀剪用M390粉末冶金不锈钢组织和性能的影响[J]. 金属热处理, 2022, 47(4): 189-195.
[11]	王瑞琴, 葛鹏, 廖强, 侯鹏, 刘宇. 固溶冷却方式对短时用高温钛合金板材组织和性能的影响[J]. 金属热处理, 2022, 47(4): 196-198.
[12]	王绍灼, 孟晗, 王芬, 樊海卫, 李燕, 唐超. 改善低氧TC4-LC及重熔TC4钛合金性能的热处理工艺[J]. 金属热处理, 2022, 47(4): 204-207.
[13]	陈强, 陈林芳, 杨明华. 18CrNiMo7-6钢的可控气氛高温渗碳工艺[J]. 金属热处理, 2022, 47(4): 231-239.
[14]	刘乃瑜, 曹磊, 郑少梅. 不同沉积温度下CrCN涂层的力学性能[J]. 金属热处理, 2022, 47(4): 240-244.
[15]	杨春苗, 王珊, 王淑慧, 李延珍, 刘文文. RRA过程中预时效时间对7A85铝合金组织性能的影响[J]. 金属热处理, 2022, 47(3): 44-47.