时效对Fe基合金激光重熔层组织和性能的影响

doi:10.13251/j.issn.0254-6051.2020.09.020

金属热处理 ›› 2020, Vol. 45 ›› Issue (9): 111-115.DOI: 10.13251/j.issn.0254-6051.2020.09.020

时效对Fe基合金激光重熔层组织和性能的影响

杜晓洁¹, 洪永昌¹, 单军战²

1.安徽工业大学材料科学与工程学院,安徽马鞍山 243000;
2.马鞍山钢铁股份有限公司,安徽马鞍山 243100

收稿日期:2020-03-21 出版日期:2020-09-25 发布日期:2020-12-29
作者简介:杜晓洁(1989—),女,硕士,主要研究方向为高性能金属材料,E-mail:dxjxjq@163.com

Effect of aging on microstructure and properties of laser remelted layer of Fe-based alloy

Du Xiaojie¹, Hong Yongchang¹, Shan Junzhan²

1. School of Materials and Engineering,Anhui University of Technology,Ma'anshan Anhui 243000,China;
2. Ma'anshan Iron and Steel Company,Ma'anshan Anhui 243100,China

Received:2020-03-21 Online:2020-09-25 Published:2020-12-29

摘要/Abstract

摘要： 利用场发射扫描电镜、透射电镜、X射线衍射仪和电化学工作站等,对比分析了Fe基合金原始热喷焊层、在500 ℃经不同时间时效处理后激光重熔层的组织和性能。结果表明,火焰喷涂后的热喷焊层组织较粗大,经激光重熔后组织明显细化,由较细小的树枝晶间均匀分布着层片状共晶组织构成;随时效时间的增加,重熔层中距离共晶组织较近的柱状晶球化,基体中Cr₇C₃、Cr₂₃C₆型碳化物进一步析出,弥散分布在枝晶间层片状共晶组织上;时效6 h所获得的激光重熔层组织硬度最大,可达507 HV0.5,随时效时间继续增加,硬度有所下降,但仍高于未经时效处理时的激光重熔层组织硬度;热喷焊层经激光重熔,耐腐蚀能力显著提高到最强,时效6 h的激光重熔层耐腐蚀性降低不明显,时效48 h的激光重熔层的耐腐蚀性则明显降低。

关键词: 时效, 铁基合金, 激光重熔, 组织, 性能

Abstract: Microstructure and properties of thermal spraying welded layer and laser remelted layer with different aging treatment at 500 ℃ of an Fe-based alloy were compared and analyzed by using field emission scanning electron microscope(FE-SEM),transmission electron microscope(TEM),X-ray diffractometer(XRD) and electrochemical workstation.The results show that the microstructure of the thermal spraying welded layer after flame spraying is relatively coarse,which is markedly refined as composed of fine dendrites with lamellar eutectic evenly distributed in between after laser remelting.With the increase of aging time,columnar crystals closer to the eutectic structure in the remelting layer start to spheroidize,Cr₇C₃ and Cr₂₃C₆ carbides are further precipitated in the matrix and distribute in the lamellar eutectic structure between the dendrites.The hardness of the laser remelting layer aged for 6 h is the highest,as up to 507 HV0.5.With the aging time continues to increase,the hardness decreases,but it is still higher than that of the laser remelted layer without aging.After laser remelting,the corrosion resistance of the thermal spraying welded layer is significantly improved to the maximum,and that aged for 6 h is not significantly reduced,while that aged for 48 h is significantly reduced.

Key words: aging, Fe-based alloy, laser remelting, microstructure, properties

中图分类号:

TG156.92

杜晓洁, 洪永昌, 单军战. 时效对Fe基合金激光重熔层组织和性能的影响[J]. 金属热处理, 2020, 45(9): 111-115.

Du Xiaojie, Hong Yongchang, Shan Junzhan. Effect of aging on microstructure and properties of laser remelted layer of Fe-based alloy[J]. Heat Treatment of Metals, 2020, 45(9): 111-115.

参考文献

[1] 焦丽,葛保红,张燕明,等.20CrMnTi钢凸轮轴表面磨损失效分析[J].金属热处理,2015,40(9):221-224.
Jiao Li,Ge Baohong,Zhang Yanming,et al.Failure analysis on surface wear of 20CrMnTi steel camshaft[J].Heat Treatment of Metals,2015,40(9):221-224.
[2] 杨海华,毛加成,冯爱新,等.激光熔覆对20CrNi2Mo钢表面摩擦磨损性能的影响[J].应用激光,2018,38(3):29-34.
Yang Haihua,Mao Jiacheng,Feng Aixin,et al.Effects of laser cladding on friction and wear properties of 20CrNi2Mo steel[J].Applied Laser,2018,38(3):29-34.
[3] 瞿伟成,杨博程,刘延辉,等.激光表面加工技术的发展与现状[J].热加工工艺,2017,20(10):38-41.
Qu Weicheng,Yang Bocheng,Liu Yanhui,et al.Development and status of laser surface processing[J].Hot Working Technology,2017,20(10):38-41.
[4] 李泽,纪秀林,郎子樊,等.激光重熔对Fe基非晶合金涂层抗冲蚀性能的影响[J].金属热处理,2019,44(5):117-123.
Li Ze,Ji Xiulin,Lang Zifan,et al.Effect of laser remelting on slurry erosion resistance of arc-sprayed Fe-based amorphous coating[J].Heat Treatment of Metals,2019,44(5):117-123.
[5] 吕艳红,张启富,吴子健.超音速火焰喷涂CoCrW涂层热震过程中的裂纹扩展行为[J].中国表面工程,2015,28(6):87-93.
Lü Yanhong,Zhang Qifu,Wu Zijian.Extended behavior of crack during thermal shock testing of HVOF sprayed CoCrW coatings[J].China Surface Engineering,2015,28(6):87-93.
[6] 王璐.热喷涂技术在先进航空发动机上的应用及前景展望[J].有色金属(冶炼部分),2018(S1):7-9.
Wang Lu.Application and prospect of thermal spray technology in advanced aero engines[J].Nonferrous Metals(Metallurgy),2018(S1):7-9.
[7] 单军战.激光重熔及时效对Fe基合金火焰热喷焊(涂)层组织和性能的影响[D].马鞍山:安徽工业大学,2014.

[1]	王玉岱, 刘洋, 朱言言, 田象军, 程序, 冉先喆, 钱婷婷. 热处理对复合制造AerMet100超高强度钢组织均匀性与拉伸性能的影响[J]. 金属热处理, 2022, 47(4): 1-9.
[2]	张子延, 陈君, 陈晓亚, 李全安, 刘建鑫. 固溶时效处理对Mg-4Sm-3Gd-0.5Zr合金显微组织和耐蚀性能的影响[J]. 金属热处理, 2022, 47(4): 10-16.
[3]	梁恩溥, 徐乐, 杨勇, 王毛球. 添加Al、Cu对40CrNi3MoV钢组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 17-23.
[4]	祁晓亮, 李岩, 定巍, 赵增武. 含Al中锰TRIP钢原始组织对临界退火后组织与力学性能的影响[J]. 金属热处理, 2022, 47(4): 24-29.
[5]	陈保安, 张静媛, 祝志祥, 韩钰, 潘学东, 张磊, 陈素红. 化学成分对高强Al-Mg-Si合金组织和性能的影响[J]. 金属热处理, 2022, 47(4): 30-38.
[6]	陈东俊, 李广阳, 刘刚. 时效处理对AlSi9Cu3压铸铝合金组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 53-56.
[7]	陈连生, 张露友, 田亚强, 杨子旋, 李红斌, 潘红波, 魏英立. 低碳高强舰船用钢的CCT曲线及其组织性能[J]. 金属热处理, 2022, 47(4): 63-68.
[8]	贾昌远, 霍元明, 何涛, 霍存龙, 刘克然. 40CrNiMo钢高温拉伸变形行为和组织演变规律[J]. 金属热处理, 2022, 47(4): 69-74.
[9]	王云龙, 余伟, 张昳, 史佳新, 李明辉. 奥氏体化温度对贝氏体钢等温转变及力学性能的影响[J]. 金属热处理, 2022, 47(4): 80-85.
[10]	陈思君, 陈送义, 陈庚, 袁丁玲, 陈康华. Mg含量对2A14铝合金组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 86-92.
[11]	刘丽艳, 毕文珍, 韦习成. Mn元素对热冲压钢镀锌层组织演变的影响[J]. 金属热处理, 2022, 47(4): 93-99.
[12]	骆再斌, 范子泽, 彭振. 轻质高熵合金的研究进展[J]. 金属热处理, 2022, 47(4): 100-107.
[13]	白青青, 张志宏, 郑淮北, 王英虎. 2507超级双相不锈钢中σ相的析出行为[J]. 金属热处理, 2022, 47(4): 108-115.
[14]	陈刚, 罗小兵, 柴锋, 杨才福, 张正延, 杨丽. 轧制加热温度对高强度低合金钢组织及冲击性能的影响[J]. 金属热处理, 2022, 47(4): 116-121.
[15]	付锡彬, 陈子豪, 张可, 赵时雨, 孙新军, 朱正海, 梁小凯, 雍岐龙. 淬火温度对高Ti低合金耐磨钢组织及力学性能的影响[J]. 金属热处理, 2022, 47(4): 122-127.

时效对Fe基合金激光重熔层组织和性能的影响

Effect of aging on microstructure and properties of laser remelted layer of Fe-based alloy

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价