基于22MnB5钢的铌钒微合金化热成形钢的研发

doi:10.13251/j.issn.0254-6051.2021.01.021

金属热处理 ›› 2021, Vol. 46 ›› Issue (1): 109-113.DOI: 10.13251/j.issn.0254-6051.2021.01.021

基于22MnB5钢的铌钒微合金化热成形钢的研发

刘纲^1,2, 干勇², 刘崇³, 马鸣图¹, 吴坚⁴, 杨应东⁴, 胡春林⁴

1.中国汽车工程研究院股份有限公司,重庆 401122;
2.中国钢研科技集团有限公司钢铁研究总院,北京 100081;
3.河钢集团钢研总院,河北石家庄 050023;
4.马鞍山钢铁股份有限公司长材事业部,安徽马鞍山 243011

收稿日期:2020-06-23 出版日期:2021-01-25 发布日期:2021-01-26
通讯作者: 刘崇,工程师,硕士,E-mail:1447659223@qq.com
作者简介:刘纲(1982—),男,教授级高级工程师,博士,主要研究方向为特殊钢冶炼、材料成型等,E-mail:121197276@qq.com。

Development of Nb-V microalloyed hot forming steel based on 22MnB5

Liu Gang^1,2, Gan Yong², Liu Chong³, Ma Mingtu¹, Wu Jian⁴, Yang Yingdong⁴, Hu Chunlin⁴

1. China Automotive Engineering Research Institute Co.,Ltd.,Chongqing 401122,China;
2. Central Iron & Steel Research Institute,CISRI,Beijing 100081,China;
3. Central Iron and Steel Research Institute,HBIS Group,Shijiazhuang Hebei 050023,China;
4. Long Products Business Division,Ma'anshan Iron and Steel Co.,Ltd.,Ma'anshan Anhui 243011,China

Received:2020-06-23 Online:2021-01-25 Published:2021-01-26

摘要/Abstract

摘要： 基于现有热成形零件冷弯性能不足、氢脆敏感性强等共性技术问题,在22MnB5钢的基础上采用Nb、V微合金化的设计思路,对试验钢的显微组织、淬透性和极限尖冷弯性能进行研究。结果表明:微合金化前后22MnB5热成形钢的显微组织均为全马氏体,但是微合金化后的试验钢组织更为细小;Nb-V微合金化能有效提高22MnB5热成形钢的淬透性,其淬硬层深度达到13～14 mm,并且试验钢的极限尖冷弯角达到58°～72°,进一步拓宽了热冲压成形的工艺窗口。综合分析试验钢微观组织、淬透性能及极限尖冷弯性能的检测结果,添加0.04%Nb和0.04%V实现复合微合金化,提升材料的综合强塑性,满足了高冷弯性能汽车零部件用材需求。

关键词: 22MnB5钢, 微合金化, 极限尖冷弯性能

Abstract: Based on the common technical problems of insufficient cold bending performance and strong hydrogen embrittlement sensitivity of existing hot forming steel parts,the design idea of Nb and V microalloying was adopted on the basis of 22MnB5 steel,and the microstructure,hardenability and extreme tip cold bending performance of the tested steels were studied.The results show that the microstructure of hot forming steel 22MnB5 before and after microalloying is all martensite,while becomes finer after microalloying;Nb-V microalloying can effectively improve the hardenability of the 22MnB5 hot forming steel,the depth of hardened layer reaches 13-14 mm,and the extreme tip cold bending angle of the tested steels reaches 58°-72°,which further widens the processing window of hot forming forming.Based on the test results of microstructure,hardenability and extreme tip cold bending performance of the tested steels,the comprehensive strength and plasticity of the steel are improved by adding 0.04%Nb and 0.04%V,and meet the requirements of automotive parts with high extreme tip cold bending performance.

Key words: 22MnB5 steel, microalloying, extreme tip cold bending performance

中图分类号:

TG142.45

刘纲, 干勇, 刘崇, 马鸣图, 吴坚, 杨应东, 胡春林. 基于22MnB5钢的铌钒微合金化热成形钢的研发[J]. 金属热处理, 2021, 46(1): 109-113.

Liu Gang, Gan Yong, Liu Chong, Ma Mingtu, Wu Jian, Yang Yingdong, Hu Chunlin. Development of Nb-V microalloyed hot forming steel based on 22MnB5[J]. Heat Treatment of Metals, 2021, 46(1): 109-113.

参考文献

[1] 刘宗巍,史天泽,郝瀚,等.中国汽车技术的现状、发展需求与未来方向[J].汽车技术,2017(1):1-6.
Liu Zongwei,Shi Tianze,Hao Han,et al.Current situation,development demand and future trend of automotive technologies in China[J].Automobile Technology,2017(1):1-6.
[2] 易红亮,常智渊,才贺龙,等.热冲压成形钢的强度与塑性及断裂应变[J].金属学报,2020,56(4):429-443.
Yi Hongliang,Chang Zhiyuan,Cai Helong,et al.Strength,ductility and fracture strain of press-hardening steels[J].Acta Metallurgica Sinica,2020,56(4):429-443.
[3] 李光瀛.汽车构件与零部件新材料及其热处理新技术的发展与应用[J].金属热处理,2010,35(12):1-13.
Li Guangying.Development and application of new materials and new technology in heat treatment for auto panels and auto components[J].Heat Treatment of Metals,2010,35(12):1-13.
[4] 王国栋.金属材料先进热处理装备、工艺和产品研发[J].金属热处理,2016,41(1):1-7.
Wang Guodong.Research and development of advanced heat treatment equipment,technology and product for metal materials[J].Heat Treatment of Metals,2016,41(1):1-7.
[5] 王存宇,杨洁,常颖,等.先进高强度汽车钢的发展趋势与挑战[J].钢铁,2019,54(2):1-6.
Wang Cunyu,Yang Jie,Chang Ying,et al.Development trend and challenge of advanced high strength automobile steels[J].Iron and Steel,2019,54(2):1-6.
[6] 惠亚军,潘辉,李文远,等.1000 MPa 级 Nb-Ti 微合金化超高强度钢加热制度研究[J].金属学报,2017,53(2):129-139.
Hui Yajun,Pan Hui,Li Wenyuan,et al.Study on heating schedule of 1000 MPa grade Nb-Ti microalloyed ultra-high strength steel[J].Acta Metallurgica Sinica,2017,53(2):129-139.
[7] 杨海根,赵征志,杨源华,等.1800 MPa 级冷轧热成形钢的组织与性能[J].材料热处理学报,2017,38(7):120-125.
Yang Haigen,Zhao Zhengzhi,Yang Yuanhua,et al.Microstructure and properties of 1800 MPa-grade cold-rolled hot stamping steel[J].Transactions of Materials and Heat Treatment,2017,38(7):120-125.
[8] Zhang S,Fan E,Wan J,et al.Effect of Nb on the hydrogen-induced cracking of high-strength low-alloy steel[J].Corrosion Science,2018,139:83-96.
[9] 李孟星,孟祥海,马涛,等.第二相粒子对高强船板钢焊接HAZ影响的研究进展[J].热加工工艺,2018,47(19):1-5.
Li Mengxing,Meng Xianghai,Ma Tao,et al.Research progress of influence of second phase particles on welding HAZ of high strength ship plate steel[J].Hot Working Technology,2018,47(19):1-5.
[10] 宋欣,杨海峰,王川,等.屈服强度1100 MPa级超高强钢热处理组织及性能[J].钢铁研究学报,2019,31(6):592-600.
Song Xin,Yang Haifeng,Wang Chuan,et al.Microstructures and properties of 1100 MPa grade ultra-high strength steel after heat treatments[J].Journal of Iron and Steel Research,2019,31(6):592-600.
[11] 张爱文,徐震,李青,等.Nb对V-Ti复合微合金化曲轴用非调质钢组织、性能的影响[J].钢铁,2004(6):63-66.
Zhang Aiwen,Xu Xia,Li Qing,et al.Effect of Nb on microstructure and properties of non-quenched and tempered steel with V-Ti combined addition used for crankshaft[J].Iron and Steel,2004(6):63-66.
[12] 高志玉,潘涛,王卓,等.高淬透性硼微合金化特厚板钢成分优化设计[J].工程科学学报,2015,37(4):447-453.
Gao Zhiyu,Pan Tao,Wang Zhuo,et al.Composition optimization design of boron-microalloying ultra-heavy plate steel with high hardenability[J].Chinese Journal of Engineering,2015,37(4):447-453.
[13] 余凯,程和法,陈文琳,等.扭力梁热成形过程温度与微观组织的研究[J].塑性工程学报,2017,24(3):109-114.
Yu Kai,Cheng Hefa,Chen Wenlin,et al.Temperature and microstructure of torsion beam during hot forming[J].Journal of Plasticity Engineering,2017,24(3):109-114.
[14] 温盾,赵刚,魏钢城.热连轧汽车大梁板T52L性能控制的研究[J].武汉科技大学学报(自然科学版),2006(5):460-464.
Wen Dun,Zhao Gang,Wei Gangcheng.Property control of T52L continuous hot-rolled plate for automotive frame[J].Journal of Wuhan University of Science and Technology,2006(5):460-464.

[1]	刘丽艳, 毕文珍, 韦习成. Mn元素对热冲压钢镀锌层组织演变的影响[J]. 金属热处理, 2022, 47(4): 93-99.
[2]	于洪军, 程福超, 马泽天, 王永金, 陈俊豪, 陈正家, 宋传颂馨. 不同水韧处理工艺下铌微合金化高锰钢的组织演变和力学性能[J]. 金属热处理, 2022, 47(4): 151-154.
[3]	张鹏程, 武会宾. Ti微合金化对耐火建筑钢组织和性能的影响[J]. 金属热处理, 2022, 47(2): 9-13.
[4]	王舒镜, 王同浩, 王剑, 李玉平, 韩培德. B-Ce复合微合金化对S31254超级奥氏体不锈钢组织和力学性能的影响[J]. 金属热处理, 2022, 47(2): 14-19.
[5]	郝天赐, 吴雍壕, 阴树标, 曹建春, 罗瀚宇. Zr对Ti-Mo复合微合金化钢形变奥氏体静态再结晶动力学和析出相的影响[J]. 金属热处理, 2022, 47(2): 41-47.
[6]	胡芳忠, 杨少朋, 金国忠, 胡乃悦, 汪开忠, 杨志强, 陈世杰. 淬火温度对Nb微合金化齿轮钢18CrNiMo7-6组织演变及力学性能的影响[J]. 金属热处理, 2022, 47(2): 105-111.
[7]	马启林, 刘刚, 郑健, 阴树标, 李拔, 刘清友. Nb-V复合微合金化高钢级管线钢的奥氏体连续冷却转变[J]. 金属热处理, 2022, 47(1): 13-18.
[8]	卓城之, 高丽, 顾炜华, 雍岐龙, 陆忠. Nb-V微合金化高碳钢在弹性盖板针布用钢丝上的运用[J]. 金属热处理, 2022, 47(1): 69-72.
[9]	王自敏, 杨志强, 胡芳忠, 汪开忠, 丁雷. Nb微合金化对18CrNiMo7-6钢奥氏体晶粒长大的影响[J]. 金属热处理, 2021, 46(9): 53-57.
[10]	王晓东, 陈蕴博, 左玲立, 游龙, 陈冲, 毛丰, 张峻嘉. V-N微合金化CrSiMn系低合金铸钢中的析出行为[J]. 金属热处理, 2021, 46(8): 15-19.
[11]	杨晓伟, 陈焕德, 周云, 张宇. 轧制工艺对V-Nb微合金化HRB600E钢筋组织及性能的影响[J]. 金属热处理, 2021, 46(8): 150-155.
[12]	刘洁, 徐乐, 何肖飞, 李晓源, 王毛球. Ti微合金化非调质钢中碳化物析出行为及其对再结晶的影响[J]. 金属热处理, 2021, 46(4): 9-15.
[13]	杨波, 孙健, 郭宏丽. 控制冷却工艺对Ti微合金化中碳钢板组织和性能的影响[J]. 金属热处理, 2021, 46(4): 118-121.
[14]	韩荣, 刘洪喜, 尉文超, 王毛球, 时捷. 回火温度对Ti-V-Mo微合金化马氏体钢析出相和力学性能的影响[J]. 金属热处理, 2021, 46(12): 53-60.
[15]	顾炜华, 卓城之, 陆忠, 高丽, 张永清, 雍岐龙. 碳含量对铌微合金化高碳钢制金属针布耐磨性的影响[J]. 金属热处理, 2021, 46(12): 72-75.

基于22MnB5钢的铌钒微合金化热成形钢的研发

Development of Nb-V microalloyed hot forming steel based on 22MnB5

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价