热处理工艺对G115钢铸件组织与性能的影响

doi:10.13251/j.issn.0254-6051.2021.10.011

金属热处理 ›› 2021, Vol. 46 ›› Issue (10): 65-73.DOI: 10.13251/j.issn.0254-6051.2021.10.011

热处理工艺对G115钢铸件组织与性能的影响

刘心阳^1,2, 陈正宗², 周芸¹, 包汉生²

1.昆明理工大学材料科学与工程学院, 云南昆明 650093;
2.钢铁研究总院特殊钢研究所, 北京 100081

收稿日期:2021-04-27 出版日期:2021-10-25 发布日期:2021-12-08
通讯作者: 陈正宗,高级工程师,E-mail: chenzhengzong@nercast.com
作者简介:刘心阳(1996—) ,男,硕士研究生,主要研究方向为耐热钢的组织与性能,E-mail:3014295452@qq.com
基金资助:
国家重点研发计划( 2017YFB0305202)

Effect of heat treatment on microstructure and properties of G115 steel casting

Liu Xinyang^1,2, Chen Zhengzong², Zhou Yun¹, Bao Hansheng²

1. Faculty of Materials Science and Engineering, Kunming University of Science and Technology, Kunming Yunnan 650093, China;
2. Special Steels Research Institute, Central Iron and Steel Research Institute, Beijing 100081, China

Received:2021-04-27 Online:2021-10-25 Published:2021-12-08

摘要/Abstract

摘要： 以均匀化退火后的G115钢铸件为对象,研究了不同正火+回火工艺处理对其显微组织及力学性能的影响,其中正火工艺分别为1070 ℃×1 h,AC和1100 ℃×1 h,AC,回火工艺分为一次回火(780 ℃×3 h,AC)和两次回火(780 ℃×3 h,AC+750 ℃×3 h,AC)。结果表明:随着正火温度的上升,G115钢铸件的室温强度和650 ℃高温强度均有所上升,而韧性有所下降,塑性无明显变化;随着回火次数的增加,G115钢的室温强度和650 ℃高温强度均有所降低,韧性和塑性无明显影响。正火+回火处理后G115钢铸件中的析出相主要有Laves相、M₂₃C₆以及MX(NbC、VN)相,冲击断口形貌呈解理或准解理断裂特征。随着正火温度升高,马氏体板条块(Block)宽度有所增加,排列相对整齐。原奥氏体晶粒尺寸是G115钢室温强度贡献值中晶界强化量的有效晶粒尺寸。推荐的热处理制度为1100 ℃×1 h(AC)正火+780 ℃×3 h(AC) 回火。

关键词: 热处理工艺, G115钢铸件, 力学性能, 析出相, EBSD, TEM

Abstract: Taking homogenizing annealed G115 steel casting as research subject, the effects of different (normalizing+tempering) treatment process on microstructure and mechanical properties of the steel casting were studied. The normalizing temperatures were respectively 1070 ℃ and 1100 ℃, both holding for 1 h then air cooling (AC). The tempering processes were single tempering (780 ℃×3 h, AC), and double tempering (780 ℃×3 h, AC then 750 ℃×3 h, AC), respectively. The results show that with the increase of normalizing temperature, both the room temperature strength and the 650 ℃ high temperature strength of the G115 steel casting increase somewhat, while the toughness decreases somewhat, and the plasticity does not change obviously. With the increase of tempering times, both the room temperature strength and the 650 ℃ high temperature strength decrease somewhat, while the toughness and plasticity do not change obviously. Laves phase, M₂₃C₆ and MX (NbC, VN) phases are the main precipitated phases in the G115 steel casting after normalizing and tempering, and the impact fracture is characterized by cleavage or quasi-cleavage fracture. With the increase of normalizing temperature, the width of martensite blocks increases and the arrangement is relatively neat. The prior austenite grain size is the effective grain size for grain boundary strengthening in the contribution value of the room temperature strength of G115 steel casting. In summary, the recommended heat treatment process is normalized at 1100 ℃ for 1 h, AC, then tempered at 780 ℃ for 3 h, AC.

Key words: heat treatment process, G115 steel casting, mechanical properties, precipitated phase, EBSD, TEM

中图分类号:

TG142.1

刘心阳, 陈正宗, 周芸, 包汉生. 热处理工艺对G115钢铸件组织与性能的影响[J]. 金属热处理, 2021, 46(10): 65-73.

Liu Xinyang, Chen Zhengzong, Zhou Yun, Bao Hansheng. Effect of heat treatment on microstructure and properties of G115 steel casting[J]. Heat Treatment of Metals, 2021, 46(10): 65-73.

参考文献

[1]杨素宝, 刘正东, 程世长. 超超临界火电机组用关键锅炉钢性能分析[J]. 钢铁研究学报, 2010, 22(1): 37-42.
Yang Subao, Liu Zhengdong, Cheng Shichang. Property analysis of key boiler steels used for ultra-supercritical power plants[J]. Journal of Iron and Steel Research, 2010, 22(1): 37-42.
[2]刘正东, 程世长, 包汉生, 等. 超超临界火电机组用锅炉钢技术国产化问题[J]. 钢铁, 2009, 44(6): 1-7.
Liu Zhengdong, Cheng Shichang, Bao Hansheng, et al. Localization of boiler steel technology in China used for ultra super critical power plants[J]. Iron and Steel, 2009, 44(6): 1-7.
[3]石如星. 超超临界火电机组用P92钢组织性能优化研究[D]. 北京: 钢铁研究总院, 2011.
[4]姜运建, 张文建, 李文彬. Laves相和Z相对P92钢蠕变的影响[J]. 热力发电, 2009, 38(8): 55-58.
Jiang Yunjian, Zhang Wenjian, Li Wenbin. Influence of Laves phase and Z-phase upon creep of P92 steel[J]. Thermal Power Generation, 2009, 38(8): 55-58.
[5]严鹏. 新型马氏体耐热钢G115的组织与性能研究[D]. 北京: 清华大学, 2014.
[6]刘阿娇. G115 马氏体耐热钢铸钢的组织与性能研究[D]. 西安: 西安建筑科技大学, 2019.
[7]徐洲, 赵连城. 金属固态相变原理[M]. 北京: 科学出版社, 2004.
[8]Prat O, Garcia J, Rojas D, et al. Investigations on coarsening of MX and M₂₃C₆ precipitates in 12%Cr creep resistant steels assisted by computational thermodynamics[J]. Materials Science and Engineering A, 2010, 527: 5976-5983.
[9]Cui J, Kim I S, Kang C Y, et al. Creep stress effect on the precipitation behavior of Laves phase in Fe-10%Cr-6%W alloys[J]. ISIJ International, 2001, 41: 368-371.
[10]Li Q. Precipitation of Fe₂W Laves phase and modeling of its direct influence on the strength of a 12Cr-2W steel[J]. Metallurgical and Materials Transactions A, 2006, 37: 89-97.
[11]刘鸿国, 李生志, 熊伟, 等. 马氏体耐热钢中Laves相的析出行为[J]. 材料热处理学报, 2015, 36(9): 109-113.
Liu Hongguo, Li Shengzhi, Xiong Wei, et al. Precipitation behavior and influence of Laves phase in martensitic heat resistant steel[J]. Transactions of Materials and Heat Treatment, 2015, 36(9): 109-113.
[12]雍岐龙. 钢铁材料中的第二相[M]. 北京: 冶金工业出版社, 2006.
[13]Maruyama K, Sawada K, Koike J. Strengthening mechanisms of creep resistant tempered martensitic steel[J]. ISIJ International, 2001, 41: 641-653.
[14]Sellars C M, Mctegart W J. On the mechanism of hot deformation[J]. Acta Metallurgica, 1966, 14(9): 1136-1138.
[15]Jonas J J, Sellars C M, Tegart W J M. Strength and structure under hot-working conditions[J]. International Materials Reviews, 1969, 14(1): 1-24.
[16]Sellars C M, Tegart W J M. Hot workability[J]. International Materials Reviews, 1972, 17(1): 1-24.
[17]Zener C, Hollomon J H. Effect of strain rate upon the plastic of steel[J]. Journal of Applied Physics, 1944, 15(1): 22-32.
[18]Medina S F, Hernandez C A. General expression of Zener-Hollomon parameter as a function of the chemical composition of low alloy and microalloy steels[J]. Acta Materialia, 1996, 44(1): 137-148.
[19]Vyrostkova A, Homolova V, Pecha J, et al. Phase evolution in P92 and E911 weld metals during ageing[J]. Materials Science and Engineering A, 2008, 480: 289-298.

热处理工艺对G115钢铸件组织与性能的影响

Effect of heat treatment on microstructure and properties of G115 steel casting

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	梁恩溥, 徐乐, 杨勇, 王毛球. 添加Al、Cu对40CrNi3MoV钢组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 17-23.
[2]	祁晓亮, 李岩, 定巍, 赵增武. 含Al中锰TRIP钢原始组织对临界退火后组织与力学性能的影响[J]. 金属热处理, 2022, 47(4): 24-29.
[3]	陈保安, 张静媛, 祝志祥, 韩钰, 潘学东, 张磊, 陈素红. 化学成分对高强Al-Mg-Si合金组织和性能的影响[J]. 金属热处理, 2022, 47(4): 30-38.
[4]	陈连生, 张露友, 田亚强, 杨子旋, 李红斌, 潘红波, 魏英立. 低碳高强舰船用钢的CCT曲线及其组织性能[J]. 金属热处理, 2022, 47(4): 63-68.
[5]	王云龙, 余伟, 张昳, 史佳新, 李明辉. 奥氏体化温度对贝氏体钢等温转变及力学性能的影响[J]. 金属热处理, 2022, 47(4): 80-85.
[6]	陈思君, 陈送义, 陈庚, 袁丁玲, 陈康华. Mg含量对2A14铝合金组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 86-92.
[7]	骆再斌, 范子泽, 彭振. 轻质高熵合金的研究进展[J]. 金属热处理, 2022, 47(4): 100-107.
[8]	吕杰晟, 宋志刚, 何建国, 丰涵, 郑文杰, 朱玉亮. S32205双相不锈钢冷轧退火组织转变及强塑化机理分析[J]. 金属热处理, 2022, 47(4): 141-145.
[9]	王琪, 吴光亮. 回火温度对1100 MPa级高强钢组织与性能的影响[J]. 金属热处理, 2022, 47(4): 146-150.
[10]	张骥俊, 邢彦锋, 曹菊勇. 超声振动对CMT电弧增材制造铝合金组织与性能的影响[J]. 金属热处理, 2022, 47(4): 159-164.
[11]	胡静, 陶科, 杨庆松, 李刚, 张德汉. 机械抛光后的时效工艺对0Cr25Al5电热合金拉拔性能的影响[J]. 金属热处理, 2022, 47(4): 171-177.
[12]	刘文彬, 乔龙阳, 潘新宇, 程格, 李爱娜, 裴新军. 淬火温度对刀剪用M390粉末冶金不锈钢组织和性能的影响[J]. 金属热处理, 2022, 47(4): 189-195.
[13]	王瑞琴, 葛鹏, 廖强, 侯鹏, 刘宇. 固溶冷却方式对短时用高温钛合金板材组织和性能的影响[J]. 金属热处理, 2022, 47(4): 196-198.
[14]	王绍灼, 孟晗, 王芬, 樊海卫, 李燕, 唐超. 改善低氧TC4-LC及重熔TC4钛合金性能的热处理工艺[J]. 金属热处理, 2022, 47(4): 204-207.
[15]	陈强, 陈林芳, 杨明华. 18CrNiMo7-6钢的可控气氛高温渗碳工艺[J]. 金属热处理, 2022, 47(4): 231-239.