激光功率对27SiMn钢熔覆层组织与性能的影响

doi:10.13251/j.issn.0254-6051.2022.05.032

金属热处理 ›› 2022, Vol. 47 ›› Issue (5): 194-198.DOI: 10.13251/j.issn.0254-6051.2022.05.032

激光功率对27SiMn钢熔覆层组织与性能的影响

石淑婷¹, 舒林森^1,2, 何雅娟¹, 王家胜¹

1.陕西理工大学机械工程学院, 陕西汉中 723001;
2.陕西省工业自动化重点实验室, 陕西汉中 723001

收稿日期:2021-12-07 修回日期:2022-03-09 出版日期:2022-05-25 发布日期:2022-06-16
通讯作者: 舒林森,副教授,博士, E-mail: shulinsen19@163.com
作者简介:石淑婷(1997—),女,硕士研究生,主要研究方向为激光熔覆、组织与性能,E-mail: shuting.s@qq.com。
基金资助:
国家自然科学基金(51505268); 国防科技重点实验室(JCKY61420052022); 陕西省教育厅重点项目(20JS020);陕西省教育厅专项科研计划(21JK0562); 陕西省工业自动化重点实验室开放课题研究基金(SLGPT2019KF01-16); 陕西理工大学校级科研项目(SLGKY2005)

Effect of laser power on microstructure and properties of clad layer on 27SiMn steel

Shi Shuting¹, Shu Linsen^1,2, He Yajuan¹, Wang Jiasheng¹

1. School of Mechanical Engineering, Shaanxi University of Technology, Hanzhong Shaanxi 723001, China;
2. Shaanxi Provincial Key Laboratory of Industrial Automation, Hanzhong Shaanxi 723001, China

Received:2021-12-07 Revised:2022-03-09 Online:2022-05-25 Published:2022-06-16

摘要/Abstract

摘要： 为了探寻激光功率对熔覆层组织与性能的影响,设计4种不同激光功率在27SiMn钢表面进行Fe-Cr-Ni熔覆层制备,利用超景深显微仪、显微硬度计、摩擦磨损试验机对熔覆层的显微组织、硬度、磨损量及摩擦因数进行了研究。结果表明,4种激光功率下的试件熔覆层均无气孔裂纹等缺陷,激光功率为1800 W时所制备试件的枝晶生长方向较为一致,激光功率为2400 W时所制备试件熔覆层中部的胞状晶和二次枝晶晶胞较为细小致密;随着激光功率增加,熔覆层的熔宽、熔深和稀释率逐渐增大,而熔高则先增大后减小;熔覆层硬度受激光功率影响较小,但增大激光功率可以提高热影响区硬度;激光功率为2400 W时所制备试件的平均摩擦因数最小、磨损量最少、磨损深度最小,其耐磨性能优良。

关键词: 激光熔覆, 激光功率, 27SiMn钢, Fe-Cr-Ni涂层, 摩擦磨损

Abstract: In order to explore the influence of laser power on microstructure and properties of the clad layer, four different laser powers were designed to perform Fe-Cr-Ni clad layer preparation on the surface of 27SiMn steel. The microstructure, hardness, wear loss, and friction coefficient of the clad layers were studied by means of super depth of field microscope, microhardness tester and friction and wear tester. The results show that the clad layer of the specimens under four different laser powers has no defect such as pore and crack, and the dendrite growth directions of the specimen prepared under the laser power of 1800 W are relatively consistent. The cellular crystal and the secondary dendrite in the middle part of the clad layer prepared under the laser power of 2400 W are smaller and denser. As the laser power increases, the melting width, melting depth and dilution rate of the clad layer gradually increase, while the melting height first increases and then decreases. The laser power has little effect on hardness of the clad layer, but the increase of laser power can raise the hardness of the heat affected zone. The specimen prepared under the laser power of 2400 W has the minimum average friction coefficient, the least wear loss, the minimum wear depth, and its wear resistance is excellent.

Key words: laser cladding, laser power, 27SiMn steel, Fe-Cr-Ni coating, friction and wear

中图分类号:

TN249

石淑婷, 舒林森, 何雅娟, 王家胜. 激光功率对27SiMn钢熔覆层组织与性能的影响[J]. 金属热处理, 2022, 47(5): 194-198.

Shi Shuting, Shu Linsen, He Yajuan, Wang Jiasheng. Effect of laser power on microstructure and properties of clad layer on 27SiMn steel[J]. Heat Treatment of Metals, 2022, 47(5): 194-198.

参考文献

[1]王晶晨, 贾国平, 白冰, 等. 液压支架零部件防腐及再制造工艺研究进展[J]. 材料导报, 2015, 29(21): 112-117.
Wang Jingchen, Jia Guoping, Bai Bing, et al. Research progress on antisepsis and remanufacturing process of hydraulic support components[J]. Materials Review, 2015, 29(21): 112-117.
[2]韩文静, 张培训, 汤其建, 等. 单体液压支柱缸体激光熔覆Ni60A+20%WC性能[J]. 煤炭学报, 2012, 37(2): 340-343.
Han Wenjing, Zhang Peixun, Tang Qijian, et al. Property of laser cladded Ni60A+20%WC alloy of cylinder of single hydraulic support[J]. Journal of China Coal Society, 2012, 37(2): 340-343.
[3]郭永明. 表面工程应用实例[例53]电弧喷涂在煤矿液压支架立柱修复中的应用[J]. 中国表面工程, 2018, 31(2): 2.
Guo Yongming. Examples of surface engineering applications[Example 53] application of arc spraying in the repair of hydraulic support columns in coal mines[J]. China Surface Engineering, 2018, 31(2): 2.
[4]李成, 王玉玲, 姜芙林, 等. 激光功率对超声辅助激光熔覆Al₂O₃-ZrO₂陶瓷力学性能的影响[J]. 金属热处理, 2020, 45(2): 223-229.
Li Cheng, Wang Yuling, Jiang Fulin, et al. Effect of laser power on mechanical properties of ultrasonic assisted laser clad Al₂O₃-ZrO₂ ceramic[J]. Heat Treatment of Metals, 2020, 45(2): 223-229.
[5]孙帅, 李崇桂, 李帅, 等. WC含量对激光熔覆Al₂O₃/TiO₂涂层组织与性能的影响[J]. 金属热处理, 2018, 43(12): 78-82.
Sun Shuai, Li Chonggui, Li Shuai, et al. Effect of WC content on microstructure and properties of laser clad Al₂O₃/TiO₂ coating[J]. Heat Treatment of Metals, 2018, 43(12): 78-82.
[6]王贤才, 张亚普, 柴蓉霞. 27SiMn钢表面激光熔覆304不锈钢的组织和性能[J]. 金属热处理, 2020, 45(4): 188-193.
Wang Xiancai, Zhang Yapu, Chai Rongxia. Microstructure and properties of 304 stainless steel laser cladding on 27SiMn steel surface[J]. Heat Treatment of Metals, 2020, 45(4): 188-193.
[7]郭卫, 李凯凯, 柴蓉霞, 等. 27SiMn钢表面激光熔覆铁基合金组织和耐磨性分析[J]. 应用激光, 2018, 38(3): 351-357.
Guo Wei, Li Kaikai, Chai Rongxia, et al. Analysis of microstructure and wear resistance of Fe-based alloy on 27SiMn steel surface by laser cladding[J]. Applied Laser, 2018, 38(3): 351-357.
[8]黎文强. 液压支架激光熔覆强化层的组织与性能[J]. 金属热处理, 2019, 44(5): 83-86.
Li Wenqiang. Microstructure and properties of laser cladding reinforced layer of hydraulic support[J]. Heat Treatment of Metals, 2019, 44(5): 83-86.
[9]Shen F M, Tao W, Li L Q, et al. Effect of microstructure on the corrosion resistance of coatings by extreme high speed laser cladding[J]. Applied Surface Science, 2020, 517: 146085.
[10]Zhang L, Wang C S, Han L Y, et al. Influence of laser power on microstructure and properties of laser clad Co-based amorphous composite coatings[J]. Surfaces and Interfaces, 2017, 6: 18-23.
[11]Li Y X, Su K Q, Bai P K, et al. Microstructure and property characterization of Ti/TiBCN reinforced Ti based composite coatings fabricated by laser cladding with different scanning speed[J]. Materials Characterization, 2020, 159: 110023.
[12]程秀全, 晏畅, 程思竹, 等. 工艺参数对激光冲击诱导表面残余应力洞的影响规律[J]. 机械工程材料, 2019, 43(11): 53-56, 61.
Cheng Xiuquan, Yan Chang, Cheng Sizhu, et al. Influence rule of process parameters on residual stress cave induced by laser shock[J]. Materials for Mechanical Engineering, 2019, 43(11): 53-56, 61.
[13]李广琪, 朱刚贤, 赵亮, 等. 离焦量对中空环形激光熔覆层温度场及应力场的影响[J]. 中国机械工程, 2021, 32(5): 587-593, 599.
Li Guangqi, Zhu Gangxian, Zhao Liang, et al. Influence of defocusing amount on temperature and stress field of hollow-ring laser cladding layer[J]. China Mechanical Engineering, 2021, 32(5): 587-593, 599.
[14]邱莹, 张凤英, 胡腾腾, 等. 激光功率对TC4表面熔覆Ti40阻燃钛合金组织及硬度的影响[J]. 中国激光, 2019, 46(11): 167-175.
Qiu Ying, Zhang Fengying, Hu Tengteng, et al. Effect of laser power on microstructure and hardness of Ti40 flame-retardant titanium alloy deposited by laser cladding on TC4 surface[J]. Chinese Journal of Lasers, 2019, 46(11): 167-175.
[15]Wang C L, Gao Y, Zeng Z C, et al. Effect of rare-earth on friction and wear properties of laser cladding Ni-based coatings on 6063Al[J]. Journal of Alloys and Compounds, 2017, 727: 278-285.

激光功率对27SiMn钢熔覆层组织与性能的影响

Effect of laser power on microstructure and properties of clad layer on 27SiMn steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	董月, 舒林森. 离焦量对MoS₂改性Fe-Cr-Mo-Si合金涂层组织与性能的影响[J]. 金属热处理, 2022, 47(5): 246-251.
[2]	欧阳昌耀, 白峭峰, 韩斌慧, 闫献国. 激光熔覆Fe基非晶合金涂层裂纹分析[J]. 金属热处理, 2022, 47(5): 252-256.
[3]	李梦, 武美萍, 陆佩佩, 赵子硕, 缪小进. 选区激光熔化MnSi₂增强316L不锈钢复合材料的表面质量及耐蚀性能[J]. 金属热处理, 2022, 47(4): 165-170.
[4]	石铭霄, 王雄栋, 李敬勇, 杨志东, 茅卫东, 倪慧锋. AISI 410钢膏剂渗硼工艺渗层的组织与性能[J]. 金属热处理, 2022, 47(4): 245-250.
[5]	赵子硕, 武美萍, 缪小进, 崔宸, 龚玉玲. 激光功率对FeCoNiCrMo高熵合金/氧化石墨烯复合涂层组织及耐腐蚀性能的影响[J]. 金属热处理, 2022, 47(4): 251-257.
[6]	林基辉, 温亚辉, 范文博, 张腾, 刘晨雨, 薛元琳. 钛合金表面激光改性技术研究进展[J]. 金属热处理, 2022, 47(3): 215-221.
[7]	丁涛, 张云华, 李俊杰, 刘进, 刘艳. 不锈钢表面激光熔覆技术研究现状与展望[J]. 金属热处理, 2022, 47(2): 205-212.
[8]	卢庆亮, 王静, 戚小霞, 李燕乐, 李方义. 面向盾构机密封跑道修复的激光熔覆Fe基涂层制备工艺[J]. 金属热处理, 2022, 47(1): 202-211.
[9]	李礼, 叶宏, 刘越, 佘红艳, 屈威, 沈大臣, 陈梨. Cr12MoV钢表面激光熔覆Ni/Ni-WC梯度涂层的组织与耐磨性能[J]. 金属热处理, 2021, 46(9): 223-228.
[10]	龚玉玲, 武美萍, 崔宸, 缪小进. 搭接率对TC4表面Ni60A熔覆层组织性能的影响[J]. 金属热处理, 2021, 46(9): 229-233.
[11]	缪小进, 夏思海, 武美萍, 俞经虎, 赵子硕, 崔宸, 张春雷. 添加CeO₂对铝合金表面激光熔覆铝钛熔覆层性能的影响[J]. 金属热处理, 2021, 46(9): 234-240.
[12]	周建波, 张晶, 张蕾涛, 李海涛, 樊帅奇, 徐金富. 激光工艺参数对Ni60/WC涂层裂纹率及组织的影响[J]. 金属热处理, 2021, 46(9): 252-257.
[13]	马植甄, 朱佳浩, 张晖. Si对高熵合金涂层组织和高温抗氧化性能的影响[J]. 金属热处理, 2021, 46(8): 46-50.
[14]	龚玉玲, 武美萍, 崔宸, 李杨. 激光功率对TC4合金表面Ni60A/CeO₂熔覆层组织及耐腐蚀性能的影响[J]. 金属热处理, 2021, 46(8): 236-240.
[15]	崔陆军, 郝超杰, 郭士锐, 郑博, 曹衍龙, 曾文涵. 细长轴表面激光熔覆轨迹理论分析与试验研究[J]. 金属热处理, 2021, 46(7): 201-206.