铌微合金化高强塑积冷轧DP780钢的I&Q&P工艺

doi:10.13251/j.issn.0254-6051.2022.10.032

金属热处理 ›› 2022, Vol. 47 ›› Issue (10): 191-197.DOI: 10.13251/j.issn.0254-6051.2022.10.032

铌微合金化高强塑积冷轧DP780钢的I&Q&P工艺

杨康¹, 史娜², 丁敬³, 于良³, 方强³

1.马鞍山钢铁股份有限公司销售公司, 安徽马鞍山 243003;
2.马鞍山钢铁股份有限公司技术中心, 安徽马鞍山 243003;
3.马鞍山钢铁股份有限公司特钢公司, 安徽马鞍山 243003

收稿日期:2022-05-16 修回日期:2022-08-19 出版日期:2022-10-25 发布日期:2022-12-15
作者简介:杨康(1988—),男,助理工程师,主要研究方向为轧材产品与工艺技术开发,E-mail: mgykang@163.com

I&Q&P process of Nb microalloyed cold-rolled DP780 steel with high product of strength and elongation

Yang Kang¹, Shi Na², Ding Jing³, Yu Liang³, Fang Qiang³

1. Sales and Technical Service Department, Maanshan Iron and Steel Company, Maanshan Anhui 243003, China;
2. Technology Center, Maanshan Iron and Steel Company, Maanshan Anhui 243003, China;
3. Special Steel Branch, Maanshan Iron and Steel Company, Maanshan Anhui 243003, China

Received:2022-05-16 Revised:2022-08-19 Online:2022-10-25 Published:2022-12-15

摘要/Abstract

摘要： 基于亚稳奥氏体形变诱导相变理论,在实验室采用盐浴炉对800 MPa级冷轧双相钢DP780的I&Q&P(临界退火与淬火配分)工艺进行了探讨,并采用光学显微镜、扫描电镜、拉伸试验机与XRD对不同工艺下试验钢的组织性能进行了研究。结果表明,在I&Q&P工艺试验条件下,试验钢的显微组织由铁素体、马氏体与残留奥氏体组成;830 ℃退火时铁素体晶粒尺寸以＞5 μm为主,860 ℃退火下其晶粒尺寸以＜5 μm为主。830 ℃退火时试验钢的力学性能随淬火温度的变化波动较大,860 ℃退火时试验钢的力学性能随淬火温度的变化波动较小。860 ℃退火+260 ℃淬火时,试验钢的综合力学性能最佳,其抗拉强度、伸长率与强塑积分别为802 MPa、26.8%与21.5 GPa·%,钢中残留奥氏体含量高达13.89%。

关键词: 铌微合金化, 双相钢DP780, I&Q&P工艺, 组织, 力学性能

Abstract: Based on the theory of metastable austenite deformation induced phase transformation, the I&Q&P (intercritical annealing and quenching and partitioning) process of 800 MPa grade cold-rolled DP780 steel was investigated by using salt bath furnace in the laboratory. The microstructure and mechanical properties of the tested steel under different processes were studied by means of metallographic microscope, scanning electron microscope, tensile testing machine and XRD. The results indicate that the microstructure of the tested steel is composed of ferrite, martensite and retained austenite under the I&Q&P process. The ferrite grain size is mainly larger than 5 μm at annealing temperature of 830 ℃, however, the ferrite grain size is mainly smaller than 5 μm at annealing temperature of 860 ℃. The mechanical properties of the tested steel annealed at 830 ℃ fluctuate greatly with the change of quenching temperature, conversely, the mechanical properties of the tested steel annealed at 860 ℃ vary slightly. At annealing temperature of 860 ℃ and quenching temperature of 260 ℃, the optimum comprehensive mechanical properties are obtained with tensile strength of 802 MPa, elongation of 26.8%, and product of strength and elongation of 21.5 GPa·%, and the content of retained austenite in the steel is as high as 13.89%.

Key words: Nb microalloying, dual-phase steel DP780, I&Q&P process, microstructure, mechanical properties

中图分类号:

TG156

杨康, 史娜, 丁敬, 于良, 方强. 铌微合金化高强塑积冷轧DP780钢的I&Q&P工艺[J]. 金属热处理, 2022, 47(10): 191-197.

Yang Kang, Shi Na, Ding Jing, Yu Liang, Fang Qiang. I&Q&P process of Nb microalloyed cold-rolled DP780 steel with high product of strength and elongation[J]. Heat Treatment of Metals, 2022, 47(10): 191-197.

参考文献

[1]李运刚, 马涛, 李慧蓉, 等. Fe-Mn-Al-C低密度钢强化机制与拉伸性能研究进展及Nb微合金化展望[J]. 材料导报, 2020, 34(23): 158-168.
Li Yungang, Ma Tao, Li Huirong, et al. Progress on strengthening mechanism and tensile properties of Fe-Mn-Al-C low density steel and prospect of Nb microalloying[J]. Materials Reports, 2020, 34(23): 158-168.
[2]康永林. 汽车轻量化先进高强钢与节能减排[J]. 钢铁, 2008, 43(6): 1-7.
Kang Yonglin. Lightweight vehicle, advanced high strength steel and energy saving and emission reduction[J]. Steel, 2008, 43(6): 1-7.
[3]Senuma T. Physical metallurgy of modern high strength steel sheets[J]. ISIJ International, 2001, 41(6): 520-532.
[4]Jin W, Da S B, Liang C, et al. The microstructure and formability study on DP Steel of lightweight automobile[J]. Materials Science Forum, 2012, 704-705: 1465-1472.
[5]Tasan C C, Diehl M, Yan D, et al. An overview of dual-phase steels: Advances in microstructure-oriented processing and micromechanically guided design[J]. Annual Review of Materials Research, 2015, 45(1): 391-431.
[6]Emil E, Ján K, Katarína B, et al. The prediction of the mechanical properties for dual-phase high strength steel grades based on microstructure characteristics[J]. Metals, 2018, 8(4): 242.
[7]Kuziak R, Kawalla R, Waengler S. Advanced high strength steels for automotive industry[J]. Archives of Civil and Mechanical Engineering, 2008, 8(2): 103-117.
[8]Koh-Ichi S, Akihiko N, Mitsuyuki K, et al. Effects of retained austenite parameters on warm stretch-flangeability in TRIP-aided dual-phase sheet steels[J]. ISIJ International, 2007, 39(1): 56-63.
[9]Chiang J, Lawrence B, Boyd J D, et al. Effect of microstructure on retained austenite stability and work hardening of TRIP steels[J]. Materials Science and Engineering A, 2011, 528(13): 4516-4521.
[10]Bhargava M, Chakrabarty S, Barnwal V K, et al. Effect of microstructure evolution during plastic deformation on the formability of transformation induced plasticity and quenched and partitioned AHSS[J]. Materials & Design, 2018, 152: 65-77.
[11]Dai Z, Chen H, Yang Z G, et al. Fundamentals and application of solid-state phase transformations for advanced high strength steels containing metastable retained austenite[J]. Materials Science and Engineering R, 2021, 143: 1-39.
[12]Thiessen R G, Paul G, Sebald R. Relationship between microstructure and mechanical properties in Q&P-steels[J]. Materials Science Forum, 2017, 879: 1933-1938.
[13]Speer J, Matlock D K, Cooman B, et al. Carbon partitioning into austenite after martensite transformation[J]. Acta Materialia, 2003, 51(9): 2611-2622.
[14]詹华, 冷德平, 潘红波, 等. Nb对0.2C-1.5Si-1.8Mn淬火配分钢组织和力学性能的影响[J]. 金属热处理, 2020, 45(3): 73-77.
Zhan Hua, Leng Deping, Pan Hongbo, et al. Influence of Nb on microstructure and mechanical properties of 0.2C-1.5Si-1.8Mn quenching and partitioning steel[J]. Heat Treatment of Metals, 2020, 45(3): 73-77.
[15]付立铭, 单爱党, 王巍. 低碳Nb微合金钢中Nb溶质拖曳和析出相NbC钉扎对再结晶晶粒长大的影响[J]. 金属学报, 2010, 46(7): 832-837.
Fu Liming, Shan Aidang, Wang Wei. Effect of Nb solute drag and NbC precipitation pinning on the recrystallization grain growth in low carbon Nb-microalloyed steel[J]. Acta Metallurgica Sinica, 2010, 46(7): 832-837.
[16]Wang C Y, Shi J, Cao W Q, et al. Characterization of microstructure obtained by quenching and partitioning process in low alloymartensitic steel[J]. Materials Science and Engineering A, 2010, 527(15): 3442-3449.
[17]Su Y Y, Chiu L H, Chuang T L, et al. Retained austenite amount determination comparison in JISSKD11 steel using quantitative metallography and X-Ray diffraction methods[J]. Advanced Materials Research, 2012, 482-484: 1165-1168.
[18]YB/T 5338—2006, 钢中残余奥氏体定量测定X射线衍射仪法[S].
[19]Zheng C, Raabe D. Interaction between recrystallization and phase transformation during intercritical annealing in a cold-rolled dual-phase steel: A cellular automaton model[J]. Acta Materialia, 2013, 61(14): 5504-5517.

铌微合金化高强塑积冷轧DP780钢的I&Q&P工艺

I&Q&P process of Nb microalloyed cold-rolled DP780 steel with high product of strength and elongation

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	王志文, 杨荣东, 黄元春, 李辉. 时效处理对挤压成型2195铝锂合金组织和力学性能的影响[J]. 金属热处理, 2022, 47(9): 6-11.
[2]	高星, 张宁, 丁燕, 蒋波. 热处理时间对激光选区成形TC4钛合金组织及力学性能的影响[J]. 金属热处理, 2022, 47(9): 12-17.
[3]	夏朋昭, 许莹, 蔡艳青, 赵思坛, 娄冰洁. 微波烧结工艺对Ti-Mg复合材料组织和性能的影响[J]. 金属热处理, 2022, 47(9): 18-26.
[4]	林凌峰, 袁鸽成, 杨濂, 丁灿培. 平均道次压下率对异步轧制-固溶6016铝合金板材显微组织的影响[J]. 金属热处理, 2022, 47(9): 36-40.
[5]	王璐, 王峰, 张明伟, 刘瑞, 傅正元, 刘景顺. 退火工艺对Ti-4Al-2V合金组织及耐蚀性能的影响[J]. 金属热处理, 2022, 47(9): 41-46.
[6]	李磊, 朱旭军, 张丽, 田福政. 喷丸直径对GH4169合金性能和损伤演化的影响[J]. 金属热处理, 2022, 47(9): 47-53.
[7]	潘冉, 刘宝胜, 曾元松, 曲海涛, 王东, 慕延宏. 深冷处理对15%SiC_p/2009铝基复合材料组织与力学性能的影响[J]. 金属热处理, 2022, 47(9): 65-70.
[8]	张浩泽, 王隽生, 宫鹏辉, 詹海艺, 王凯. 热处理对EB铸锭直接轧制TC4合金板材组织和力学性能的影响[J]. 金属热处理, 2022, 47(9): 71-78.
[9]	钟立伟, 冯朝辉, 高文理, 陈军洲, 陆政. 多轴锻造与T852热处理对Al-Cu-Li合金组织及力学性能的影响[J]. 金属热处理, 2022, 47(9): 79-86.
[10]	肖结良, 孙浩, 李飞, 胡平, 陈旌钢, 江兆峰. 球墨铸铁行走轮的低温正火工艺[J]. 金属热处理, 2022, 47(9): 98-102.
[11]	季德静, 杨维宇, 白雅琼. 高强韧工程机械用钢Q690D的淬火工艺优化[J]. 金属热处理, 2022, 47(9): 108-112.
[12]	温方明, 郝晓博, 曹恒, 张强, 李渤渤, 刘茵琪. 热处理工艺对N06600合金热轧板组织与性能的影响[J]. 金属热处理, 2022, 47(9): 113-118.
[13]	艾兵权, 邝霜, 田秀刚, 杨峰, 王玉慧, 逯志强, 王朝, 郝雷. 均热温度对不同成分980 MPa级高强钢组织和性能的影响[J]. 金属热处理, 2022, 47(9): 119-124.
[14]	王世凯, 王睿, 康燕, 于志强, 闫志杰. 淬火温度对Cr5MoVNi钢组织和性能的影响[J]. 金属热处理, 2022, 47(9): 125-129.
[15]	熊维亮, 梁文, 吴腾, 梁亮, 吴浩鸿. 控冷工艺对热轧双相钢组织与性能的影响[J]. 金属热处理, 2022, 47(9): 130-133.