新型700 MPa级高强锚杆钢的微观组织及强化机制

doi:10.13251/j.issn.0254-6051.2023.05.007

金属热处理 ›› 2023, Vol. 48 ›› Issue (5): 41-48.DOI: 10.13251/j.issn.0254-6051.2023.05.007

新型700 MPa级高强锚杆钢的微观组织及强化机制

孟亚森¹, 潘丽芳², 张红旭³, 刘鹏³, 任志峰¹, 刘光明¹

1.太原科技大学材料科学与工程学院, 山西太原 030024;
2.太原科技大学安全与应急管理工程学院, 山西太原 030024;
3.山西通才工贸有限公司, 山西临汾 043000

收稿日期:2022-11-11 修回日期:2023-03-13 出版日期:2023-05-25 发布日期:2023-06-21
通讯作者: 刘光明,教授,博士,E-mail: gmliu2011@163.com
作者简介:孟亚森(1995—),男,硕士研究生,主要研究方向为高强锚杆钢的组织性能,E-mail: mengyasen0812@163.com。
基金资助:
山西省应用基础研究计划(201901D111241);山西省留学人员科技活动择优项目(20210046)

Microstructure and strengthening mechanism of a novel 700 MPa grade high strength anchor steel

Meng Yasen¹, Pan Lifang², Zhang Hongxu³, Liu Peng³, Ren Zhifeng¹, Liu Guangming¹

1. School of Materials Science and Engineering, Taiyuan University of Science and Technology, Taiyuan Shanxi 030024, China;
2. School of Engineering for Safety and Emergency Management, Taiyuan University of Science and Technology, Taiyuan Shanxi 030024, China;
3. Shanxi Tongcai Industry and Trade Co., Ltd., Linfen Shanxi 043000, China

Received:2022-11-11 Revised:2023-03-13 Online:2023-05-25 Published:2023-06-21

摘要/Abstract

摘要： 自主设计了700 MPa级高强锚杆钢,采用光学显微镜、扫描电镜和透射电镜等对其微观组织与性能进行了系统测试与表征,并进一步讨论了其强化机制。结果表明,该锚杆用钢的显微组织为珠光体和铁素体复相组织,铁素体呈细小的等轴状,珠光体呈长条形片层状分布,组织中珠光体体积分数约为43%;铁素体基体上析出了大量小于20 nm的纳米级V(C, N)粒子;试验钢屈服强度约为734 MPa,抗拉强度约为936 MPa,断后伸长率约为15.1%,屈强比约为0.78,具有良好的综合性能;该锚杆钢的强化机制为细晶强化、固溶强化、位错强化及析出强化的耦合强化,其中,细晶强化及固溶强化引起的强度贡献约占总强度值的73%。

关键词: 锚杆钢, 力学性能, 强化机制, 微观组织

Abstract: Microstructure and mechanical properties of a self-designed 700 MPa grade high strength anchor steel were investigated systematically by means of optical microscope, scanning electron microscope as well as transmission electron microscope, etc, and the strengthening mechanisms of the tested steel were further quantitatively discussed. The results show that the microstructure of the tested anchor steel is composed of banded laminated pearlite and fine equiaxed ferrite, the volume fraction of pearlite is about 43%, and in the ferrite there are a large amount of nano-sized V(C, N) precipitated particles (<20 nm). In addition, the tested steel has good comprehensive properties, with the yield strength, tensile strength, and elongation after fracture being respectively about 734 MPa, 936 MPa, and 15.1%, and the yield ratio being about 0.78. The strengthening mechanism of the tested anchor steel is a coupling of grain refining strengthening, solid solution strengthening, dislocation strengthening, and precipitation strengthening, where the contributions induced by grain refining strengthening and solid solution strengthening account for about 73% of the total strength.

Key words: anchor steel, mechanical properties, strengthening mechanism, microstructure

中图分类号:

TG142.4

孟亚森, 潘丽芳, 张红旭, 刘鹏, 任志峰, 刘光明. 新型700 MPa级高强锚杆钢的微观组织及强化机制[J]. 金属热处理, 2023, 48(5): 41-48.

Meng Yasen, Pan Lifang, Zhang Hongxu, Liu Peng, Ren Zhifeng, Liu Guangming. Microstructure and strengthening mechanism of a novel 700 MPa grade high strength anchor steel[J]. Heat Treatment of Metals, 2023, 48(5): 41-48.

参考文献

[1]邸全康, 周玉丽, 程四华, 等. 600 MPa级煤巷支护锚杆钢的开发与质量控制[J]. 煤炭科学技术, 2011, 39(9): 76-80.
Di Quankang, Zhou Yuli, Cheng Sihua, et al. Development and quality control of 600 MPa steel bar for bolt applied to seam gateway support[J]. Coal Science and Technology, 2011, 39(9): 76-80.
[2]刘德军, 左建平, 刘海雁, 等. 我国煤矿巷道支护理论及技术的现状与发展趋势[J]. 矿业科学学报, 2020, 5(1): 22-33.
Liu Dejun, Zuo Jianping, Liu Haiyan, et al. Development and present situation of support theory and technology in coal mine roadway in China[J]. Journal of Mining Science and Technology, 2020, 5(1): 22-33.
[3]王晓燕, 孙汝林, 王璐. MG500锚杆用热轧带肋钢筋研制与开发[J]. 金属制品, 2014, 40(4): 48-51.
Wang Xiaoyan, Sun Rulin, Wang Lu. Research and development of MG500 hot-rolled ribbed bar for anchor rod[J]. Metal Products, 2014, 40(4): 48-51.
[4]吴拥政, 康红普, 丁吉, 等. 超高强热处理锚杆开发与实践[J]. 煤炭学报, 2015, 40(2): 308-313.
Wu Yongzheng, Kang Hongpu, Ding Ji, et al. Development and application of ultrahigh-heat processed rock bolts[J]. Journal of China Coal Society, 2015, 40(2): 308-313.
[5]陈立勇, 柴建铭, 袁永文, 等. BHRB600热轧高强韧树脂锚杆钢筋的开发[J]. 轧钢, 2007(4): 66-69.
Chen Liyong, Chai Jianming, Yuan Yongwen, et al. Development of high strength and toughness BHRB600 hot rolled resin anchor steel bars[J]. Steel Rolling, 2007(4): 66-69.
[6]吴静, 甄维静, 李永亮. MG600锚杆钢的奥氏体晶粒长大规律[J]. 金属热处理, 2019, 44(4): 76-81.
Wu Jing, Zhen Weijing, Li Yongliang. Austenite grain growth behavior of MG600 anchor steel[J]. Heat Treatment of Metals, 2019, 44(4): 76-81.
[7]Wen T, Hu X F, Song Y Y, et al. Carbides and mechanical properties in Fe-Cr-Ni-Mo high-strength steel with different V contents[J]. Materials Science and Engineering A, 2013, 588: 201-207.
[8]侯晓英, 毕永杰, 郝亮. 热轧TRP980钢微观组织及强化机制分析[J]. 钢铁, 2019, 54(4): 63-67, 82.
Hou Xiaoying, Bi Yongjie, Hao Liang. Analysis on microstructure and strengthening mechanisms of hot-rolled TRIP980 steel[J]. Iron & Steel, 2019, 54(4): 63-67, 82.
[9]徐曼, 孙新军, 刘清友, 等. 低碳含钒钢组织变化及V(C, N)析出规律[J]. 钢铁钒钛, 2005(2): 25-30.
Xu Man, Sun Xinjun, Liu Qingyou, et al. Microstructural evolution and precipitation of V(C, N) in a low-carbon V-bearing steel[J]. Iron Steel Vanadium Titanium, 2005(2): 25-30.
[10]林晏民. CONSTEEL电炉生产的小型连轧螺纹钢屈服效应不明显现象的研究[J]. 钢铁, 2004(1): 51-54.
Lin Yanmin. Study of implicit yield of re-bar production CONSTEEL-EAF-small continues rolling mill route[J]. Iron & Steel, 2004(1): 51-54.
[11]冯浩洲, 王蓬, 李冬玲, 等. 火车车轮轮辋组织与显微硬度的统计分布表征[J]. 钢铁研究学报, 2022, 34(3): 280-287.
Feng Haozhou, Wang Peng, Li Dongling, et al. Statistical distribution characterization of train wheel rim structure and microhardness[J]. Journal of Iron and Steel Research, 2022, 34(3): 280-287.
[12]Hong S G, Kang K B, Park C G. Strain-induced precipitation of NbC in Nb and Nb-Ti microalloyed HSLA steels[J]. Scripta Materialia, 2002, 46(2): 163-168.
[13]雍岐龙. 钢铁材料中的第二相[M]. 北京: 冶金工业出版社, 2006.
[14]Chipman J. Thermodynamics and phase diagram of the Fe-C system[J]. Metallurgical and Materials Transactions B, 1972, 3: 55-64.
[15]Pickering F B. Physical Metallurgy and the Design of Steels[M]. London: Applied Science Publishers Ltd., 1978.
[16]Liu C T, Gurland J. The strengthening mechanism in spheroidized carbon steels[J]. Transaction of the Metallurgical Society of AIME, 1968, 242: 1535-1542.
[17]Song R, Ponge D, Raabe D, et al. Overview of processing, microstructure and mechanical properties of ultrafine grained bcc steels[J]. Materials Science and Engineering: A, 2006, 441(1/2): 1-17.
[18]曾泽芸, 李长荣, 黎志英, 等. 终冷温度对高强度抗震钢筋组织和性能的影响[J]. 材料研究学报, 2021, 35(11): 857-865.
Zeng Zeyun, Li Changrong, Li Zhiying, et al. Effect of final temperature of cooling on microstructure and properties of aseismic high-strength steel rebar[J]. Chinese Journal of Materials Research, 2021, 35(11): 857-865.
[19]李显, 余志军, 杨跃标, 等. 高性能建筑结构用钢组织性能和强化机理研究[J]. 四川冶金, 2022, 44(1): 11-17.
Li Xian, Yu Zhijun, Yang Yuebiao, et al. Study on microstructure, mechanical properties and strengthening mechanisms of high performance steel for building structure[J]. Sichuan Metallurgy, 2022, 44(1): 11-17.
[20]惠亚军, 潘辉, 刘锟, 等. 600 MPa级Nb-Ti微合金化高成形性元宝梁用钢的强化机制[J]. 金属学报, 2017, 53(8): 937-946.
Hui Yajun, Pan Hui, Liu Kun, et al. Strengthening mechanism of 600 MPa grade Nb-Ti microalloyed high formability crossbeam steel[J]. Acta Metallurgica Sinica, 2017, 53(8): 937-946.
[21]Ashby M F. Strengthening Methods in Crystals[M]. London: Applied Science Publishers Ltd., 1971.
[22]Olalla V C, Bliznuk V, Sanchez N, et al. Analysis of the strengthening mechanisms in pipeline steels as a function of the hot rolling parameters[J]. Materials Science and Engineering A, 2014, 604: 46-56.
[23]Thillou V. Basic metal processing research institute report[R]. Pittsburgh, PA, USA: University of Pittsburgh, 1997.
[24]Gladman T. Precipitation hardening in metals[J]. Material Science and Technology, 1999, 15: 30-36.
[25]Gladman T. The Physical Metallurgy of Microalloyed Steels[M]. London: The Institute of Materials, 1997.

新型700 MPa级高强锚杆钢的微观组织及强化机制

Microstructure and strengthening mechanism of a novel 700 MPa grade high strength anchor steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	张家豪, 李红斌, 赵志浩, 徐海卫, 韩赟, 田亚强, 陈连生. 超细晶铁素体双峰结构及其对中碳钢力学性能的影响[J]. 金属热处理, 2023, 48(5): 54-59.
[2]	孙颖, 郑留伟, 张慧云. 选区激光熔化打印Al_0.5CoCrFeNiTi_0.5/316L复合材料的微纳力学及耐蚀性能[J]. 金属热处理, 2023, 48(5): 60-65.
[3]	张浩, 迟宏宵, 王成蹊, 马党参, 樊译, 谢官利. 新型N合金化Cr13型耐蚀塑料模具钢的组织性能[J]. 金属热处理, 2023, 48(5): 110-115.
[4]	李季, 曹振, 罗平, 肖治同, 李炯利, 王旭东. 烧结温度对热压烧结Ti-6Al-4V合金组织与性能的影响[J]. 金属热处理, 2023, 48(5): 166-173.
[5]	杨智凯, 张欣悦, 易林, 闫星辰, 王志. 固溶处理对选区激光熔化双相不锈钢组织及性能的影响[J]. 金属热处理, 2023, 48(5): 174-183.
[6]	韩哲文, 王智春, 王家健, 王启冰, 彭波, 左月, 司明宇, 康举. 恢复热处理对R26高温合金螺栓组织和力学性能的影响[J]. 金属热处理, 2023, 48(5): 184-190.
[7]	张贺全, 谢撰业, 朱鑫, 程海英, 马宏亚, 吕正风, 王广彦. 34CrNi3MoV钢箱体热处理工艺优化[J]. 金属热处理, 2023, 48(5): 224-228.
[8]	张光莹, 定巍, 李岩, 冯继科, 董瑞. 预处理工艺对中锰TRIP钢微观组织和力学性能的影响[J]. 金属热处理, 2023, 48(5): 259-264.
[9]	刘阳, 吴晓蓝, 饶茂, 毛雪晶, 高坤元, 魏午, 熊湘沅, 黄晖. Er、Zr微合金化对Al-Zn-Mg合金组织及性能的影响[J]. 金属热处理, 2023, 48(4): 18-22.
[10]	王子波, 江畅, 陆恒昌, 满廷慧, 左锦中, 董瀚. SWRCH35K钢连续冷却转变曲线的测定与分析[J]. 金属热处理, 2023, 48(4): 23-27.
[11]	杨苗, 林茂, 孙福德, 刘钧, 陈哲, 王浩伟. 固溶处理对TiB₂/7050Al复合材料组织与性能的影响[J]. 金属热处理, 2023, 48(4): 53-59.
[12]	任健斌, 王昆, 梁伟, 聂慧慧, 李线绒. 弯曲矫直变形路径对ZK60镁合金板材组织及性能的影响[J]. 金属热处理, 2023, 48(4): 74-78.
[13]	张明旭, 徐旺, 李涌泉, 董福元. 冷轧+退火对CoCrNi中熵合金显微组织和力学性能的影响[J]. 金属热处理, 2023, 48(4): 85-88.
[14]	留灵锴, 张静, 伊军英, 杨维姝, 肖浩, 孟雪. 镁合金预变形时效处理工艺的研究现状[J]. 金属热处理, 2023, 48(4): 89-96.
[15]	程体娟, 于鸿垚, 毕中南, 杜金辉. 固溶处理对新型镍钴基高温合金显微组织及力学性能的影响[J]. 金属热处理, 2023, 48(4): 97-103.