20Si2Mn2CrNi钢Ms点下的等温转变组织及其强韧性

doi:10.13251/j.issn.0254-6051.2023.07.003

金属热处理 ›› 2023, Vol. 48 ›› Issue (7): 15-21.DOI: 10.13251/j.issn.0254-6051.2023.07.003

20Si2Mn2CrNi钢Ms点下的等温转变组织及其强韧性

吴忠潮¹, 周拥军², 段宝玉¹, 侯渊¹, 呼云飞³, 高占勇¹

1.内蒙古科技大学材料与冶金学院, 内蒙古包头 014010;
2.内蒙古一机集团富成锻造有限责任公司, 内蒙古包头 014030;
3.内蒙古华泽装备制造有限公司, 内蒙古鄂尔多斯 016062

收稿日期:2023-01-04 修回日期:2023-05-22 出版日期:2023-07-25 发布日期:2023-09-04
通讯作者: 高占勇,教授,博士,E-mail: 15804722665@163.com
作者简介:吴忠潮(1999—),男,硕士研究生,主要研究方向为高强钢的强韧化与工程应用,E-mail: 1052080879@qq.com。
基金资助:
鄂尔多斯市科技重大专项(2021ZD工25-7);内蒙古自治区重点研发和成果转化项目(2022YFHH0098)

Isothermal microstructure and strength and toughness of 20Si2Mn2CrNi steel below Ms

Wu Zhongchao¹, Zhou Yongjun², Duan Baoyu¹, Hou Yuan¹, Hu Yunfei³, Gao Zhanyong¹

1. School of Materials and Metallurgy, Inner Mongolia University of Science and Technology, Baotou Inner Mongolia 014010, China;
2. Fucheng Forge Company of Inner Mongolia First Machinery Group Co., Ltd., Baotou Inner Mongolia 014030, China;
3. Inner Mongolia Huze Equipment Manufacturing Co., Ltd., Erdos Inner Mongolia 016062, China

Received:2023-01-04 Revised:2023-05-22 Online:2023-07-25 Published:2023-09-04

摘要/Abstract

摘要： 采用热膨胀法研究了一种低碳低合金B/M复相高强20Si2Mn2CrNi钢在Ms点(386 ℃)附近等温淬火的相变动力学,运用K-M 模型定性地计算了Ms点以下等温淬火时的马氏体体积分数,研究了试验钢在不同等温淬火工艺下的组织转变对其力学性能的影响规律。结果表明,试验钢在高于386 ℃等温时过冷奥氏体转变为上贝氏体,而在386 ℃以下等温时除形成马氏体外,还形成了与386 ℃以上奥氏体等温转变为贝氏体动力学一致的低温贝氏体。试验钢在300 ℃等温淬火时,马氏体体积分数为91.74%,硬度为41.7 HRC,冲击吸收能量为91.7 J,具有较好的强塑性综合力学性能,这与贝氏体组织与马氏体组织良好的协调变形有关。

关键词: 20Si2Mn2CrNi钢, 贝氏体, 马氏体, 等温淬火, 力学性能

Abstract: Phase transformation kinetics of a low carbon low alloy B/M dual-phase high-strength 20Si2Mn2CrNi steel during isothermal quenching around 386 ℃ was studied using thermal expansion method. The volume fraction of martensite below the Ms point during isothermal quenching was qualitatively calculated using the K-M model, and the influence of microstructural transformation under different isothermal quenching processes on the mechanical properties was investigated. The results show that the experiment steel transforms to upper bainite when it is isothermally quenched above 386 ℃, while forming not only martensite but also low-temperature bainite with the same kinematics as bainite transformation from austenite above 386 ℃ when it is isothermally quenched below 386 ℃. When the experimental steel is isothermally quenched at 300 ℃, the volume fraction of martensite is 91.74%, the hardness is 41.7 HRC, and the impact absorbed energy is 91.7 J, showing good comprehensive mechanical properties of strength and plasticity due to the well-coordinated deformation between bainite and martensite microstructure.

Key words: 20Si2Mn2CrNi steel, bainite, martensite, austempering, mechanical properties

中图分类号:

TG142.1

吴忠潮, 周拥军, 段宝玉, 侯渊, 呼云飞, 高占勇. 20Si2Mn2CrNi钢Ms点下的等温转变组织及其强韧性[J]. 金属热处理, 2023, 48(7): 15-21.

Wu Zhongchao, Zhou Yongjun, Duan Baoyu, Hou Yuan, Hu Yunfei, Gao Zhanyong. Isothermal microstructure and strength and toughness of 20Si2Mn2CrNi steel below Ms[J]. Heat Treatment of Metals, 2023, 48(7): 15-21.

参考文献

[1]陈明义. 培育壮大我国的海洋工程装备制造业[J]. 发展研究, 2011(5): 4-6.
[2]范长刚, 董瀚, 雍岐龙, 等. 低合金超高强度钢的研究进展[J]. 机械工程材料, 2006, 30(8): 1-4.
Fan Changgang, Dong Han, Yong Qilong, et al. Research development of ultra-high strength low alloy steels[J]. Materials for Mechanical Engineering, 2006, 30(8): 1-4.
[3]王涛亮, 路妍, 任凤章, 等. 低合金超高强度钢研究进展[J]. 金属热处理, 2015, 40(2): 13-20.
Wang Taoliang, Lu Yan, Ren Fengzhang, et al. Research progress of ultra-high strength low alloy steels[J]. Heat Treatment of Metals, 2015, 40(2): 13-20.
[4]杨静. 低合金高碳钢低温等温淬火组织和力学性能的研究[D]. 秦皇岛: 燕山大学, 2008.
Yang Jing. Study on microstructures and mechanical properties of low-alloyed high-carbon steels by low-temperature isothermal treatment[D]. Qinghuangdao: Yanshan University, 2008.
[5]吴化, 张翠翠, 梁言, 等. 低合金超级贝氏体钢组织形态的研究[J]. 材料科学与工艺, 2014, 22(5): 102-107.
Wu Hua, Zhang Cuicui, Liang Yan, et al. Study on microstructure of the low-alloying super bainitic steel[J]. Materials Science and Technology, 2014, 22(5): 102-107.
[6]董宝奇. 低温贝氏体钢的力学性能及其强磁场下的相变[D]. 武汉: 武汉科技大学, 2019.
Dong Baoqi. Mechanical properties of low-temperature bainitic steel and phase transformation under high magnetic field[D]. Wuhan: Wuhan University of Science and Technology, 2019.
[7]吴亚杰. 热处理工艺对中高碳低温贝氏体钢组织和性能的影响[D]. 武汉: 武汉科技大学, 2019.
Wu Yajie. Effect of heat treatment processes on microstructure and properties of medium and high carbon low temperature bainitic steels[D]. Wuhan: Wuhan University of Science and Technology, 2019.
[8]马胜宾, 滕敦波, 王俊翔. 热处理工艺对高C-Cr高强耐磨钢组织和性能的影响[J]. 中国冶金, 2021, 31(6): 39-44.
Ma Shengbin, Teng Dunbo, Wang Junxiang. Influence of heat treatment on microstructure and properties of high C-Cr high strength wear-resistant steel[J]. China Metallurgy, 2021, 31(6): 39-44.
[9]Koistinen D P, Marburger R E. A general equation prescribing the extent of the austenite-martensite transformation in pure iron-carbon alloys and plain carbon steels[J]. Acta Metallurgica 1959, 7: 59-60.
[10]Bohemen S M C V, Santofimia M J, Sietsma J. Experimental evidence for bainite formation below Ms in Fe-0.66C[J]. Scripta Materialia, 2008, 58(6): 488-491.
[11]Gong W, Tomota Y, Harjo S, et al. Effect of prior martensite on bainite transformation in nanobainite steel[J]. Acta Materialia, 2015, 85: 243-249.
[12]殷汉奇, 许红军. 硝盐淬火技术[J]. 热处理, 2015, 30(3): 36-44.
Yin Hanqi, Xu Hongjun. Quenching in molten nitrate-nitrite salt[J]. Heat Treatment, 2015, 30(3): 36-44.
[13]张峦, 顾敏, 王爱香, 等. 硝盐淬火介质的冷却特性[J]. 金属热处理, 2015, 40(6): 212-215.
Zhang Luan, Gu Min, Wang Aixiang, et al. Cooling characteristics of nitrate quenching medium[J]. Heat Treatment of Metals, 2015, 40(6): 212-215.
[14]Samanta S, Biswas P, Giri S, et al. Formation of bainite below the Ms temperature: Kinetics and crystallography[J]. Acta Materialia, 2016, 105: 390-403.
[15]Navarro-Lopez A, Hidalgo J, Sietsma J, et al. Characterization of bainitic/martensitic structures formed in isothermal treatments below the Ms temperature[J]. Materials Characterization, 2017, 128: 248-256.
[16]Zhao L, Qian L, Zhou Q, et al. The combining effects of ausforming and below-Ms or above-Ms austempering on the transformation kinetics, microstructure and mechanical properties of low-carbon bainitic steel[J]. Materials and Design, 2019, 183: 108123.
[17]Zhao L, Qian L, Meng J, et al. Below-Ms austempering to obtain refined bainitic structure and enhanced mechanical properties in low-C high-Si/Al steels[J]. Scripta Materialia, 2016, 112: 96-100.
[18]Samanta S, Biswas P, Singh S B. Analysis of the kinetics of bainite formation below the Ms temperature[J]. Scripta Materialia, 2017, 136: 132-135.
[19]刘宗昌, 计云萍. 马氏体组织形貌形成机理[J]. 热处理技术与装备, 2019, 40(4): 1-7.
Liu Zongchang, Ji Yunping. Formation mechanism of martensite morphology[J]. Heat Treatment Technology and Equipment, 2019, 40(4): 1-7.
[20]黄维刚, 方鸿生, 郑燕康. 硅对Mn-B系空冷贝氏体钢组织与性能的影响[J]. 材料热处理学报, 1997, 18(1): 10-15.
Huang Weigang, Fang Hongsheng, Zheng Yankang. Effect of silicon on microstructure and properties of Mn-B modified bainite steel[J]. Transactions of Materials and Heat Treatment, 1997, 18(1): 10-15.
[21]黄维刚, 徐蓉, 方鸿生, 等. 中低碳含硅空冷贝氏体钢的冲击韧性[J]. 钢铁研究学报, 1997, 9(2): 35-38.
Huang Weigang, Xu Rong, Fang Hongsheng, et al. Impact toughness of medium-low carbon silicon modified bainitic steel[J]. Journal of Iron and Steel Research, 1997, 9(2): 35-38.
[22]徐祖耀. 马氏体相变与马氏体[M]. 2版. 北京: 科学出版社, 1999: 556-565.
[23]Miihkinen V T T, Edmonds D V. Fracture toughness of two experimental high-strength bainitic low-alloy steels containing silicon[J]. Materials Science and Technology, 1987, 3(6): 441-449.
[24]Miihkinen V T T, Edmonds D V. Tensile deformation of two experimental high-strength bainitic low-alloy steels containing silicon[J]. Materials Science and Technology, 1987, 3(6): 432-440.
[25]Miihkinen V T T, Edmonds D V. Microstructural examination of two experimental high-strength bainitic low-alloy steels containing silicon[J]. Materials Science and Technology, 1987, 3(6): 422-431.
[26]吴彬彬. 高强度低合金钢晶体学特征及其成分-工艺-性能关系研究[D]. 北京: 北京科技大学, 2020.
Wu Binbin. Study on crystallographic characteristics of high strengh low alloy steel and its composition-process-performance relationship[D]. Beijing: University of Science and Technology Beijing, 2020.
[27]Lei X, Huang J, Chen S, et al. Expanded lever rule for phase volume fraction calculation of high-strength low-alloy steel in thermal simulation[J]. Metallurgical and Materials Transactions A, 2016, 47(6): 2795-2803.
[28]徐祖耀. 低碳钢中的残余奥氏体[J]. 上海金属, 1995, 17(1): 1-6.
Xu Zuyao. Retained austenite in low carbon steels[J]. Shanghai Metals, 1995, 17(1): 1-6.
[29]Zhang X M, Li D F, Xing Z S. Morphology transition of deformation-induced lenticular martensite in Fe-Ni-C alloys[J]. Acta Metallurgica et Materials, 1993, 41(1): 1693-1699.
[30]任勇强, 谢振家, 尚成嘉. 低碳钢中残留奥氏体的调控及对力学性能的影响[J]. 金属学报, 2012, 48(9): 1074-1080.
Ren Yongqiang, Xie Zhenjia, Shang Chengjia. Regulation of retained austenite and its effect on the mechanical properties of low carbon steel[J]. Acta Metallurgica Sinica, 2012, 48(9): 1074-1080.
[31]周涛. 马氏体基高强钢强韧化机理研究与物理建模[D]. 北京: 北京科技大学, 2018.
Zhou Tao. Study of strengthening and toughening, and physically based modelling of martensite-based high-strength steels[D]. Beijing: University of Science and Technology Beijing, 2018.

20Si2Mn2CrNi钢Ms点下的等温转变组织及其强韧性

Isothermal microstructure and strength and toughness of 20Si2Mn2CrNi steel below Ms

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	赵倩, 乔志霞, 董纪, 张亚然, 何彪, 钱阔. WB36CN1钢连续冷却转变产物分析[J]. 金属热处理, 2023, 48(7): 22-25.
[2]	刘宜林, 陈如柑, 贾玉心, 李玉胜, 范雯, 郑小腾. 异构中碳双相钢丝的微观组织与力学性能[J]. 金属热处理, 2023, 48(7): 32-37.
[3]	陈俊, 张覃轶, 邓锦强, 袁胜福, 周鸿锋, 伍冬. 马氏体不锈钢回火过程中碳化物的演变规律及其对耐蚀性的影响[J]. 金属热处理, 2023, 48(7): 38-43.
[4]	韩顺, 李刚, 杨豪, 厉鑫洋, 厉勇, 王春旭. 回火温度对N63钢组织及力学性能的影响[J]. 金属热处理, 2023, 48(7): 79-83.
[5]	刘永宝, 周丽娜, 刘明, 高翔, 石东丹. 回火参数对G95Cr18马氏体不锈钢显微组织及力学性能的影响[J]. 金属热处理, 2023, 48(7): 103-110.
[6]	王军亮, 周铁柱, 付利国, 郁炎, 李春辉. 去应力退火对B10铜镍合金厚壁三通表面残余应力及组织性能的影响[J]. 金属热处理, 2023, 48(7): 111-116.
[7]	龚雪婷, 赵吉庆, 杨钢, 杨滨. 回火温度对20Cr1Mo1VTiB螺栓钢组织和性能的影响[J]. 金属热处理, 2023, 48(7): 117-123.
[8]	唐鹏, 黄嘉良, 刘倩男, 邓松云. 时效时间对7075-T6铝合金组织与性能的影响[J]. 金属热处理, 2023, 48(7): 131-137.
[9]	熊雪刚, 陈述, 陈述, 吕兵, 张开华, 周磊磊, 周伟. 回火工艺对Q125高强油井管用钢组织和性能的影响[J]. 金属热处理, 2023, 48(7): 138-142.
[10]	胡武, 吴艳梅, 黄显赞, 黄炎毅, 廖斌. 预处理对6082铝合金型材性能的影响[J]. 金属热处理, 2023, 48(7): 143-147.
[11]	王浩军, 胡生双, 肖君, 张颖, 张颖云, 高婷婷, 欧阳德来. B-Ti57CuZrNi钎料对接钎焊TC4钛合金接头的组织和性能[J]. 金属热处理, 2023, 48(7): 148-151.
[12]	王会敏, 李炎光, 吴静依. 固溶时间对2219铝合金组织和力学性能的影响[J]. 金属热处理, 2023, 48(7): 152-156.
[13]	李世文, 熊伟, 张文亮, 王超, 高占勇. 20Si2Mn2CrNi钢锻后晶粒细化及强韧性提升工艺[J]. 金属热处理, 2023, 48(7): 157-161.
[14]	杨雄, 李鹏. 中温压力容器用钢15CrMoR的热处理工艺[J]. 金属热处理, 2023, 48(7): 181-186.
[15]	赵虎林, 苟藏红. 冷轧和退火对纯镍拼焊接头组织和力学性能的影响[J]. 金属热处理, 2023, 48(7): 197-200.