自然时效耦合预拉伸提升Al-Zn-Mg-Cu合金力学性能和腐蚀抗力

doi:10.13251/j.issn.0254-6051.2024.04.017

金属热处理 ›› 2024, Vol. 49 ›› Issue (4): 104-110.DOI: 10.13251/j.issn.0254-6051.2024.04.017

自然时效耦合预拉伸提升Al-Zn-Mg-Cu合金力学性能和腐蚀抗力

董泰励^1,2, 李昉³, 陈庚^1,2, 张晨^1,2, 郭子龙^1,2, 陈康华^1,2,3, 陈送义^1,2

1.中南大学轻合金研究院, 湖南长沙 410083;
2.中南大学有色金属先进结构材料与制造协同创新中心, 湖南长沙 410083;
3.中南大学粉末冶金研究院, 湖南长沙 410083

收稿日期:2024-01-01 修回日期:2024-03-08 出版日期:2024-04-25 发布日期:2024-05-27
通讯作者: 陈康华,教授,博士,E-mail:chenkanghuacsu@163.com
作者简介:董泰励(1998—),男,硕士研究生,主要研究方向为Al-Zn-Mg-Cu合金的组织和性能,E-mail:1903313407@qq.com。
基金资助:
国家重点研发计划(2021YFF0600504);湖南省自然科学基金(2023JJ30668)

Improving mechanical properties and corrosion resistance of Al-Zn-Mg-Cu alloy through natural aging coupled pre-stretching

Dong Taili^1,2, Li Fang³, Chen Geng^1,2, Zhang Chen^1,2, Guo Zilong^1,2, Chen Kanghua^1,2,3, Chen Songyi^1,2

1. Light Alloy Research Institute, Central South University, Changsha Hunan 410083, China
2. Collaborative Innovation Center of Advanced Nonferrous Structural Materials and Manufacturing, Central South University, Changsha Hunan 410083, China;
3. Powder Metallurgy Research Institute, Central South University, Changsha Hunan 410083, China

Received:2024-01-01 Revised:2024-03-08 Online:2024-04-25 Published:2024-05-27

摘要/Abstract

摘要： 采用透射电镜(TEM)、扫描电镜(SEM)、拉伸试验、剥落腐蚀和晶间腐蚀等手段研究了不同自然时效时间耦合3%预拉伸对Al-Zn-Mg-Cu合金时效析出组织、力学和耐腐蚀性能的影响。结果表明,自然时效4天耦合3%预拉伸能调控后续时效过程中晶界附近的时效析出行为,显著地减小晶界附近无析出带宽度。其原因是自然时效4天后晶界附近无析出带存在大量溶质原子,再经3%预拉伸在晶界附近无析出带产生大量位错,促进后续时效过程析出相形核,从而减小晶界附近无析出带。窄的晶界附近无析出带能避免位错的塞积,抑制孔洞长大和裂纹扩展,显著提高合金的伸长率。同时在阳极溶解过程中,减少被腐蚀的阳极暴露面积,从而降低腐蚀速率,增加剥落腐蚀和晶间腐蚀抗力。自然时效4天耦合3%预拉伸工艺获得的抗拉强度、伸长率和最大晶间腐蚀深度分别为562 MPa、17.23%和191.4 μm。

关键词: 形变热处理, Al-Zn-Mg-Cu合金, 无析出带, 拉伸性能, 耐腐蚀性能

Abstract: Effect of natural aging time coupled with 3% pre-stretching on the aging precipitation microstructure, mechanical properties and corrosion resistance of Al-Zn-Mg-Cu alloy was studied by using transmission electron microscope (TEM), scanning electron microscope (SEM), tensile testing, exfoliation corrosion and intergranular corrosion. The results show that natural aging for 4 days coupled with 3% pre-stretching can regulate the aging precipitation behavior near grain boundaries during subsequent aging processes, significantly reducing the width of the precipitation free zone near grain boundaries. The reason is that the precipitation free zone containing amount of solution atoms is formed after natural aging for 4 days, followed by the subsequent 3% pre-stretching to induce a large number of dislocations in precipitation free zone, promoting the subsequent aging process to precipitate phase nucleation and reducing the width of the precipitation free zone. The elongation of the Al-Zn-Mg-Cu alloy is significantly improved due to the narrow precipitation free zones near grain boundaries can avoid the accumulation of dislocations, suppress pore growth and crack propagation. Meanwhile, the exposed area of the corroded anode is reduced during the anodic dissolution process, which can reduce the corrosion rate and increase the resistance of exfoliation corrosion and intergranular corrosion. The tensile strength, elongation, and maximum intergranular corrosion depth obtained by coupling natural aging for 4 days process with 3% pre-stretching are 562 MPa, 17.23% and 191.4 μm, respectively.

Key words: thermo-mechanical treatment, Al-Zn-Mg-Cu alloy, precipitation free zone, tensile properties, corrosion resistance

中图分类号:

TG146

董泰励, 李昉, 陈庚, 张晨, 郭子龙, 陈康华, 陈送义. 自然时效耦合预拉伸提升Al-Zn-Mg-Cu合金力学性能和腐蚀抗力[J]. 金属热处理, 2024, 49(4): 104-110.

Dong Taili, Li Fang, Chen Geng, Zhang Chen, Guo Zilong, Chen Kanghua, Chen Songyi. Improving mechanical properties and corrosion resistance of Al-Zn-Mg-Cu alloy through natural aging coupled pre-stretching[J]. Heat Treatment of Metals, 2024, 49(4): 104-110.

参考文献

[1]刘守法, 王晋鹏, 李凡国. Zr添加及热处理对Al-Zn-Mg-Cu合金组织与性能的影响[J]. 金属热处理, 2018, 43(9): 27-30.
Liu Shoufa, Wang Jinpeng, Li Fanguo. Effect of Zr addition and heat treatment on microstructure and mechanical properties of Al-Zn-Mg-Cu alloy[J]. Heat Treatment of Metals, 2018, 43(9): 27-30.
[2]Li F, Dong T, Zhang C, et al. Controllable precipitation behavior near grain boundaries enabled by artificial strain concentration in age-hardening aluminum alloys[J]. Materials Science and Engineering A, 2024, 892: 146026.
[3]韩连华, 白林振, 陈慧琴. 热处理对Al-Zn-Mg-Cu合金第二相粒子分布和晶粒尺寸的影响[J]. 金属热处理, 2014, 39(8): 11-15.
Han Lianhua, Bai Linzhen, Chen Huiqin. Influence of intermediate heat treatment on distribution of second phase particles and grain size of Al-Zn-Mg-Cu alloy[J]. Heat Treatment of Metals, 2014, 39(8): 11-15.
[4]魏茂源, 王洪真, 张红, 等. 预时效处理对Al-Zn-Mg-Cu合金硬化响应及微观组织的影响[J]. 金属热处理, 2020, 45(7): 90-93.
Wei Maoyuan, Wang Hongzhen, Zhang Hong, et al. Effect of pre-aging treatment on hardening response and microstructure of Al-Zn-Mg-Cu alloy[J]. Heat Treatment of Metals, 2020, 45(7): 90-93.
[5]韩宝帅, 魏立军, 徐严谨, 等. 预变形对超高强Al-Zn-Mg-Cu合金时效组织与力学性能的影响[J]. 金属学报, 2020, 56(7): 1007-1014.
Han Baoshuai, Wei Lijun, Xu Yanjin, et al. Effect of pre-deformation on microstructure and mechanical properties of ultra-high strength Al-Zn-Mg-Cu Alloy after ageing treatment[J]. Acta Metallurgica Sinica, 2020, 56(7): 1007-1014.
[6]陈康华, 杨振, 焦慧彬, 等. 最终形变热处理对Al-Zn-Mg-Cu铝合金组织和性能的影响[J]. 湖南大学学报(自然科学版), 2019, 46(6): 24-30.
Chen Kanghua, Yang Zhen, Jiao Huibin, et al. Influence of final thermo-mechanical treatment on microstructures and properties of Al-Zn-Mg-Cu aluminum alloy[J]. Journal of Hunan University(Natural Sciences), 2019, 46(6): 24-30.
[7]Ma P, Liu C, Chen Q, et al. Natural-aging-enhanced precipitation near grain boundaries in high-strength aluminum alloy[J]. Journal of Materials Science and Technology, 2020, 46: 107-113.
[8]Yuan D, Chen K, Chen S, et al. Effect of pre-strain and quench rate on stress corrosion cracking resistance of a low-Cu containing Al-Zn-Mg-Cu alloy[J]. Materials Science and Engineering A, 2022, 833: 142374.
[9]Ogura T, Hirosawa S, Cerezo A, et al. Atom probe tomography of nanoscale microstructures within precipitate free zones in Al-Zn-Mg(-Ag) alloys[J]. Acta Materialia, 2010, 58(17): 5714-5723.
[10]Hou L, Yu H, Wang Y, et al. Tailoring precipitation/properties and related mechanisms for a high-strength aluminum alloy plate via low-temperature retrogression and re-aging processes[J]. Journal of Materials Science and Technology, 2022, 120: 15-35.
[11]Poole W, Wang X, Embury J, et al. The effect of manganese on the microstructure and tensile response of an Al-Mg-Si alloy[J]. Materials Science and Engineering A, 2019, 755: 307-317.
[12]张坤, 赵晓东, 陈慧琴, 等. 过时效析出相粒子对Al-Zn-Mg-Cu合金热加工晶粒演变的影响[J]. 轻合金加工技术, 2017, 45(9): 54-61.
Zhang Kun, Zhao Xiaodong, Chen Huiqin, et al. Influence of over-aged precipitated particles on grain evolution during hot working of Al-Zn-Mg-Cu alloy[J]. Light Alloy Fabrication Technology, 2017, 45(9): 54-61.[13]Zou Y, Wu X, Tang S, et al. Investigation on microstructure and mechanical properties of Al-Zn-Mg-Cu alloys with various Zn/Mg ratios[J]. Journal of Materials Science and Technology, 2021, 85: 106-117.
[14]Krishnan M A, Raja V. Development of high strength AA7010 aluminum alloy resistant to environmentally assisted cracking[J]. Corrosion Science, 2016, 109: 94-100.
[15]Knight S, Birbilis N, Muddle B, et al. Correlations between intergranular stress corrosion cracking, grain-boundary microchemistry, and grain-boundary electrochemistry for Al-Zn-Mg-Cu alloys[J]. Corrosion Science, 2010, 52(12): 4073-4080.
[16]丁云峰, 陈康华, 袁丁玲, 等. 新型非等温时效制度对Al-Zn-Mg-Cu合金力学性能与腐蚀性能的影响[J]. 材料热处理学报, 2021, 42(2): 27-36.
Ding Yunfeng, Chen Kanghua, Yuan Dingling, et al. Effect of new non-isothermal aging on mechanical properties and corrosion resistance of Al-Zn-Mg-Cu alloy[J]. Transactions of Materials and Heat Treatment, 2021, 42(2): 27-36.
[17]李彩琼, 夏琳, 王明刚, 等. 固溶工艺对Al-Zn-Mg-Cu合金组织与性能的影响[J]. 材料热处理学报, 2023, 44(11): 52-61.
Li Caiqiong, Xia Lin, Wang Minggang, et al. Effect of solution process on microstructure and properties of Al-Zn-Mg-Cu alloy[J]. Transactions of Materials and Heat Treatment, 2023, 44(11): 52-61.

自然时效耦合预拉伸提升Al-Zn-Mg-Cu合金力学性能和腐蚀抗力

Improving mechanical properties and corrosion resistance of Al-Zn-Mg-Cu alloy through natural aging coupled pre-stretching

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	唐恩, 彭侠超, 刘红亮, 张瑞, 王坤. 合金元素对高碳珠光体盘条钢组织和性能的影响[J]. 金属热处理, 2024, 49(4): 42-47.
[2]	马志锋, 王海龙, 赵唯一, 付祎磊, 陆政. 淬火水温及深冷处理对超高强Al-Zn-Mg-Cu合金组织及性能的影响[J]. 金属热处理, 2024, 49(4): 195-200.
[3]	张立生, 王小巩. 热轧变形对高铝316L不锈钢微观组织与性能的影响[J]. 金属热处理, 2024, 49(3): 33-36.
[4]	彭宁琦, 周文浩, 金东浩, 武会宾. 高强韧桥梁钢Q690q的单轴拉伸性能与低周疲劳性能[J]. 金属热处理, 2024, 49(2): 25-31.
[5]	陈博文, 曾强, 李钢, 彭文雅, 刘国怀. 固溶温度对DD416镍基单晶高温合金组织及拉伸性能的影响[J]. 金属热处理, 2024, 49(1): 119-126.
[6]	吕达, 韩彦光, 崔毅, 赵英利, 陈文, 张泽峰, 嵇爽. GH4169高温合金的热加工工艺[J]. 金属热处理, 2023, 48(8): 132-137.
[7]	康聪, 焦振, 穆博涛, 任驰强, 高文超, 李维, 贠鹏飞, 欧阳文博. 退火处理对Ti6321合金显微组织与力学性能的影响[J]. 金属热处理, 2023, 48(8): 149-153.
[8]	岳旭, 张明玉, 杨嘉珞, 同晓乐, 赵子博, 乔恩利, 张起, 叶红川. 热处理工艺对亚稳定β型钛合金组织与拉伸性能的影响[J]. 金属热处理, 2023, 48(7): 187-192.
[9]	陈金水, 王冲, 郭诚君, 彭炳锋, 张建波, 肖翔鹏, 杨斌. Sn及深冷拉拔对Cu-Cr-Zr合金组织和性能的影响[J]. 金属热处理, 2023, 48(5): 90-97.
[10]	刘阳, 吴晓蓝, 饶茂, 毛雪晶, 高坤元, 魏午, 熊湘沅, 黄晖. Er、Zr微合金化对Al-Zn-Mg合金组织及性能的影响[J]. 金属热处理, 2023, 48(4): 18-22.
[11]	李海涛, 于娟, 刘洪涛, 谢睿勋, 冯朝辉, 赵唯一. 新型高强韧铝锂合金的显微组织和性能[J]. 金属热处理, 2023, 48(4): 173-177.
[12]	刘全明, 肖俊峰, 龙伟民, 傅莉, 杨海瑛, 高斯峰. Sn改性Ti-Zr-Cu-Ni钎料的微观组织和力学性能[J]. 金属热处理, 2023, 48(3): 209-214.
[13]	孙威威, 剌玲敏, 张静, 梁凤啸, 秦林. TA2钛板掺杂钒离子渗碳层的耐腐蚀性能[J]. 金属热处理, 2023, 48(3): 230-235.
[14]	段继萱, 安腾, 王成宇, 谷雨, 吕旭东, 杜金辉. 固溶温度对一种新型镍基高温合金微观组织和力学性能的影响[J]. 金属热处理, 2023, 48(12): 13-20.
[15]	高云飞, 曹磊, 邱国兴, 禚学院. 热处理对新型低活化钢组织及力学性能的影响[J]. 金属热处理, 2023, 48(12): 79-86.