退火工艺对SLM AlSi10Mg合金拉伸变形行为的影响

doi:10.13251/j.issn.0254-6051.2024.06.004

金属热处理 ›› 2024, Vol. 49 ›› Issue (6): 23-28.DOI: 10.13251/j.issn.0254-6051.2024.06.004

退火工艺对SLM AlSi10Mg合金拉伸变形行为的影响

刘怡然, 李磊

内蒙古工业大学理学院, 内蒙古呼和浩特 010051

收稿日期:2023-11-13 修回日期:2024-04-26 出版日期:2024-06-25 发布日期:2024-07-29
通讯作者: 李磊,副教授,博士,E-mail:leillt@163.com
作者简介:刘怡然(2004—),女,本科生,主要研究方向为金属材料力学性能,E-mail:ngdlx@sina.com。
基金资助:
内蒙古自然科学基金(2023MS01007);内蒙古工业大学博士基金(BS2021053);内蒙古工业大学大学生创新创业训练计划(2023094001)

Effect of annealing process on tensile deformation behavior of the SLM AlSi10Mg alloy

Liu Yiran, Li Lei

College of Science, Inner Mongolia University of Technology, Hohhot Inner Mongolia 010051, China

Received:2023-11-13 Revised:2024-04-26 Online:2024-06-25 Published:2024-07-29

摘要/Abstract

摘要： 借助扫描电镜、光学显微镜、拉伸试验机等手段,研究了退火温度和退火时间对选区激光熔化(SLM)AlSi10Mg合金拉伸变形行为的影响,分析了不同退火工艺下各区域应变的演化过程。结果表明,随着退火温度的升高和退火时间的延长,SLM AlSi10Mg合金共晶Si尺寸增大,试样的搭接纹路逐渐消失,共晶组织逐渐均匀并球化;合金的塑性变形明显,大变形区域范围扩大,局部大变形区域发生颈缩;合金的抗拉强度降低,伸长率增大,显微硬度降低。经500 ℃×1 h退火后,合金伸长率由6.7%增大到15.1%,同时抗拉强度由252 MPa降低至150 MPa,具有较好的强塑性。

关键词: AlSi10Mg合金, 选区激光熔化(SLM), 退火, 微观组织, 力学性能

Abstract: With the aid of scanning electron microscope, optical microscope, tensile testing machine, effects of annealing temperature and annealing time on selective laser melted (SLM) AlSi10Mg alloy tensile deformation behavior were studied, and the regional strain under different annealing were analyzed. The results show that with the increase of annealing temperature and annealing time, the phase size of eutectic Si in the SLM AlSi10Mg alloy increases, the lap grain of the specimen gradually disappears, and the eutectic structure gradually becomes uniform and spheroidized. The plastic deformation of the alloy specimen is obvious, the large deformation area is enlarged, and the local large deformation area is necked. The tensile strength of the alloy decreases, the elongation increases and the microhardness decreases. After annealing at 500 ℃ for 1 h, the elongation of the alloy increases from 6.7% to 15.1%, and the tensile strength decreases from 252 MPa to 150 MPa. The alloy has good strength and plasticity.

Key words: AlSi10Mg alloy, selective laser melting(SLM), annealing, microstructure, mechanical properties

中图分类号:

TG146

刘怡然, 李磊. 退火工艺对SLM AlSi10Mg合金拉伸变形行为的影响[J]. 金属热处理, 2024, 49(6): 23-28.

Liu Yiran, Li Lei. Effect of annealing process on tensile deformation behavior of the SLM AlSi10Mg alloy[J]. Heat Treatment of Metals, 2024, 49(6): 23-28.

参考文献

[1]Wu J, Wang X Q, Wang W, et al. Microstructure and strength of selectively laser melted AlSil0Mg[J]. Acta Materialia, 2016, 117(7): 311-320.
[2]Fousova M, Dvorsky D, Michalcoval A, et al. Changes in the microstructure and mechanical properties of additively manufactured AlSil0Mg alloy after exposure to elevated temperatures[J]. Materials Characterization, 2018, 137(1): 119-126.
[3]Chen H Y, Gu D H, Dai D H, et al. A novel approach to direct preparation of complete lath martensite microstructure in tool steel by selective laser melting[J]. Materials Letters, 2018, 277(7): 128-131.
[4]Kang N, Ma W Y, Heraud L, et al. Selective laser melting of tungsten carbide reinforced maraging steel composite[J]. Additive Manufacturing, 2018, 22(8): 104-110.
[5]袁茂强, 郭立杰, 王永强, 等. 增材制造技术的应用及其发展[J]. 机床与液压, 2016, 44(5): 183-188.
Yuan Maoqiang, Guo Lijie, Wang Yongqiang, et al. Development and application of additive manufacturing technologies[J]. Machine Tool and Hydraulics, 2016, 44(5): 183-188.
[6]侯伟, 陈静, 储松林, 等. 选区激光熔化成形AlSil0Mg组织与拉伸性能的各向异性研究[J]. 中国激光, 2018, 45(7): 67-77.
Hou Wei, Chen Jing, Chu Songlin, et al. Anisotropy of microstructure and tensile properties of AlSi10Mg formed by selective laser melting[J]. Chinese Journal of Lasers, 2018, 45(7): 67-77.
[7]刘佩玲, 陈康敏, 赵振华. 激光3D打印AlSi10Mg铝合金点阵结构材料的组织和力学性能[J]. 金属热处理, 2020, 45(9): 142-149.
Liu Peiling, Chen Kangmin, Zhao Zhenhua. Microstructure and mechanical properties of laser 3D printed AlSi10Mg aluminum alloy lattice materials[J]. Heat Treatment of Metals, 2020, 45(9): 142-149.
[8]黄卫东, 王璐, 黄旭, 等. 热处理对SLM成形TiN/AlSi10Mg合金复合材料组织性能及残余应力的影响[J].金属热处理, 2023, 48(11): 161-167.
Huang Weidong, Wang Lu, Huang Xu, et al. Effect of heat treatment on microstructure, properties and residual stress of TiN/AlSi10Mg alloy composites fabricated by SLM[J]. Heat Treatment of Metals, 2023, 48(1l): 161-167.
[9]梁恩泉, 代宇, 白静, 等. 退火态激光选区熔化成形AlSi10Mg合金组织与力学性能[J]. 材料工程, 2022, 50(5): 156-165.
Liang Enquan, Dai Yu, Bai Jing, et al. Microstructure and mechanical property of annealing heat treated AlSi10Mg alloy fabricated by selective laser melting[J]. Journal of Materials Engineering, 2022, 50(5): 156-165.
[10]孙兵兵, 房立家, 张学军. 激光选区熔化AlSi10Mg工艺优化及显微组织研究[J]. 焊接技术, 2020, 49(2): 5-8.
Sun Bingbing, Fang Lijia, Zhang Xuejun. Study on process optimization and microstructure of AlSi10Mg prepared by selective laser melting[J]. Welding Technology, 2020, 49(2): 5-8.
[11]Cao Y, Lin X, Wang Q Z, et al. Microstructure evolution and mechanical properties at high temperature of selective laser melted AlSil0Mg[J]. Journal of Materials Science and Technology, 2021, 62(4): 162-172.
[12]闫泰起, 唐鹏钧, 陈冰清, 等. 退火温度对激光选区熔化AlSi10Mg合金微观组织及拉伸性能的影响[J]. 机械工程学报, 2020, 56(8): 37-45.
Yan Taiqi, Tang Pengjun, Chen Bingqing, et al. Effect of annealing temperature on microstructure and tensile properties of AlSi10Mg alloy fabricated by selective laser melting[J]. Journal of Mechanical Engineering, 2020, 56(8): 37-45.
[13]王永慧, 胡强, 张金辉, 等. 激光选区熔化3D打印AlSi10Mg拉伸性能影响因素[J]. 粉末冶金技术, 2022, 40(2): 152-158.
Wang Yonghui, Hu Qiang, Zhang Jinhui, et al. Influencing factors on the tensile properties of selective laser melting 3D printing AlSi10Mg[J]. Powder Metallurgy Technology, 2022, 40(2): 152-158.
[14]王悦, 王继杰, 张昊, 等. 热处理对激光选区熔化AlSi10Mg合金显微组织及力学性能的影响[J]. 金属学报, 2021, 57(5): 613-622.
Wang Yue, Wang Jijie, Zhang Hao, et al. Effects of heat treatments on microstructure and mechanical properties of AlSi10Mg alloy produced by selective laser melting[J]. Acta Metallurgica Sinica, 2021, 57(5): 613-622.
[15]Zhao C, Li W, Li J. Mapping microscale strain fields around a crack tip in molybdenum via geometric phase analysis and digital image correlation[J]. Acta Mechanica Solida Sinica, 2018, 31(A): 1-12.
[16]Kim D K, Hwang J H, Kim E Y, et al. Evaluation of the stress strain relationship of constituent phases in AlSi10Mg alloy produced by selective laser melting using crystal plasticity FEM[J]. Journal of Alloys and Compounds, 2017, 714(4): 687-697.
[17]戴云彤, 陈振宁, 朱飞鹏, 等. 小尺寸低碳钢试样吕德斯效应的三维数字图像相关测量[J]. 力学学报, 2015, 47(1): 119-126.
Dai Yuntong, Chen Zhenning, Zhu Feipeng, et al. Measurement of loders band in small size low carbon steel specimen by 3D digital image correlation method[J]. Chinese Journal of Theoretical and Applied Mechanics, 2015, 47(1): 119-126.
[18]魏亮鱼, 李磊, 崔晓, 等. 基于DIC方法的不同退火温度下Cu-Ni19合金损伤演变研究[J]. 工程力学, 2020, 37(4): 227-235.
Wei Liangyu, Li Lei, Cui Xiao, et al. Study on damage evolution of Cu-Ni19 alloy at different annealing temperatures based on DIC method[J]. Engineering Mechanics, 2020, 37(4): 227-235.
[19]张继祥, 刘嘉源, 李欢, 等. AlSi10Mg合金选区激光熔化大层厚成型及热处理工艺参数研究[J]. 重庆交通大学学报(自然科学版), 2022, 41(8): 149-156.
Zhang Jixiang, Liu Jiayuan, Li Huan, et al. Parameters of AlSi10Mg alloy selection laser melting large thickness forming and heat treatment process[J]. Journal of Chongqing Jiaotong University (Natural Science), 2022, 41(8): 149-156.

退火工艺对SLM AlSi10Mg合金拉伸变形行为的影响

Effect of annealing process on tensile deformation behavior of the SLM AlSi10Mg alloy

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	吴斯, 李非凡, 王学敏, 尚学良, 徐翔宇. 退火温度对转向架用低密度钢组织性能的影响[J]. 金属热处理, 2024, 49(6): 8-16.
[2]	王艺橦, 刘旭明, 郭函, 耿志宇, 薛峰. 脱碳退火工艺对薄规格取向硅钢织构及磁性能的影响[J]. 金属热处理, 2024, 49(6): 17-22.
[3]	吴镇宇, 秦颐鸣, 李永弟, 周培林, 周佳菊, 黎渠. 退火温度对拉深成形用Al-3.5Mg合金板材组织与性能的影响[J]. 金属热处理, 2024, 49(6): 29-35.
[4]	安庆生, 万德成, 马少康, 李杰, 张千禧. 逆相变退火对中锰钢组织演变和力学性能的影响[J]. 金属热处理, 2024, 49(6): 36-42.
[5]	张淼, 万德成, 张波, 冯运莉. Fe-0.13C-2.0Mn-0.6Al复相钢在不同退火温度下的组织与性能[J]. 金属热处理, 2024, 49(6): 43-48.
[6]	候平, 王京成, 王泽, 钱金京. 真空退火对冷拔34CrMo4钢薄壁管残余应力、组织和性能的影响[J]. 金属热处理, 2024, 49(6): 85-90.
[7]	张慧霞, 魏凯, 赵万方. 退火温度对TZM高温合金组织和性能的影响[J]. 金属热处理, 2024, 49(6): 106-109.
[8]	王雷, 伽亮亮. 热处理对体育器械用SLM制备7175铝合金组织性能的影响[J]. 金属热处理, 2024, 49(6): 115-119.
[9]	陈成, 朱琦, 席莎, 曾学良, 张学苏. 退火温度对轧制Mo-Re合金管材显微组织及力学性能的影响[J]. 金属热处理, 2024, 49(6): 123-128.
[10]	史宝良, 姜发同, 刘旭亮, 宋文斌, 金玉明, 乔蒙, 郭秋彦. 典型热成形零件的显微组织及力学性能[J]. 金属热处理, 2024, 49(6): 135-141.
[11]	薛峰, 耿志宇, 刘旭明, 毕廉, 周天鹏. 高强双相钢DP980成形极限性能及微观组织分析[J]. 金属热处理, 2024, 49(6): 164-168.
[12]	杨阳, 陈晨, 董旭, 廖普九, 张福成. 晶粒尺寸对高氮高锰奥氏体钢耐磨性的影响[J]. 金属热处理, 2024, 49(6): 169-176.
[13]	肖治同, 王方明, 颜泽华, 张勇, 曹振, 呼怀刚, 李炯利, 王旭东. SiC含量对SiC_p/2009Al复合材料微观组织及力学性能的影响[J]. 金属热处理, 2024, 49(6): 190-197.
[14]	李娜, 孙书刚, 杨建春, 汪淇. C微合金化对Fe-Mn-Cr-Ni中熵合金微观结构和力学性能的影响[J]. 金属热处理, 2024, 49(6): 206-210.
[15]	钟振东, 樊金桃, 王付胜, 陈亚军. 电磁场对铝合金组织及性能影响的研究进展[J]. 金属热处理, 2024, 49(6): 261-269.