轻-重稀土混合添加对Al-Si-Mg合金显微组织和力学性能的影响

doi:10.13251/j.issn.0254-6051.2024.08.006

金属热处理 ›› 2024, Vol. 49 ›› Issue (8): 36-41.DOI: 10.13251/j.issn.0254-6051.2024.08.006

轻-重稀土混合添加对Al-Si-Mg合金显微组织和力学性能的影响

曾祥军, 史志铭, 赵鸽, 廉浩, 刘佳成

内蒙古工业大学材料科学与工程学院, 内蒙古呼和浩特 010051

收稿日期:2024-01-26 修回日期:2024-06-20 出版日期:2024-08-25 发布日期:2024-09-27
通讯作者: 史志铭,教授,博士,E-mail:shizm@imut.edu.cn
作者简介:曾祥军(1998—),男,硕士研究生,主要研究方向为稀土铝合金改性,E-mail:zxj1176855881@163.com。

Effect of mixed addition of light and heavy rare earth elements on microstructure and mechanical properties of Al-Si-Mg alloy

Zeng Xiangjun, Shi Zhiming, Zhao Ge, Lian Hao, Liu Jiacheng

School of Materials Science and Engineering, Inner Mongolia University of Technology, Hohhot Inner Mongolia 010051, China

Received:2024-01-26 Revised:2024-06-20 Online:2024-08-25 Published:2024-09-27

摘要/Abstract

摘要： 采用光学显微镜、扫描电镜/能谱仪和力学性能测试仪研究了轻-重稀土(La、Ce、Gd、Ho、Er)混合添加对Al-6.9Si-0.36Mg合金显微组织和力学性能的影响。结果表明,当稀土总添加量为0.1%时,铸态合金中α-Al晶粒细化效果明显,当稀土总添加量为0.4%时,对共晶Si相的改善效果明显,共晶Si相由粗大针状转变为颗粒状。经T6热处理后,共晶Si相进一步转变为细小颗粒状并均匀分布于基体中,降低了对基体的割裂作用。稀土总添加量为0.4%时,T6热处理态合金的力学性能最佳,抗拉强度、断后伸长率和硬度分别达到285.4 MPa、7.0%和89.2 HBW。

关键词: 稀土, Al-Si-Mg合金, 显微组织, 力学性能

Abstract: Effect of mixed addition of light and heavy rare earth elements (La, Ce, Gd, Ho, Er) on the microstructure and mechanical properties of Al-6.9Si-0.36Mg alloy was studied by using optical microscope, scanning electron microscope/energy dispersive spectroscopy, and mechanical property testers. The results show that the refinement effect of α-Al grains in the as-cast alloy is significant with total rare earth addition of 0.1%. As total amount of rare earth added is 0.4%, the improvement effect on the eutectic Si phase is significant, and the eutectic Si phase changes from coarse needle-shaped to granular. After T6 heat treatment, the eutectic Si phase further transforms into small particles and uniformly distribute in the matrix, reducing the cutting effect on the matrix. When the total amount of rare earth elements added is 0.4%, the mechanical properties of the T6 heat treated alloy are the best with tensile strength of 285.4 MPa, elongation after fracture of 7.0%, and hardness of 89.2 HBW.

Key words: rare earth, Al-Si-Mg alloy, microstructure, mechanical properties

中图分类号:

TG146.2

曾祥军, 史志铭, 赵鸽, 廉浩, 刘佳成. 轻-重稀土混合添加对Al-Si-Mg合金显微组织和力学性能的影响[J]. 金属热处理, 2024, 49(8): 36-41.

Zeng Xiangjun, Shi Zhiming, Zhao Ge, Lian Hao, Liu Jiacheng. Effect of mixed addition of light and heavy rare earth elements on microstructure and mechanical properties of Al-Si-Mg alloy[J]. Heat Treatment of Metals, 2024, 49(8): 36-41.

参考文献

[1]Lin Y C, Luo S C, Huang J, et al. Effects of solution treatment on microstructures and micro-hardness of a Sr-modified Al-Si-Mg alloy[J]. Materials Science and Engineering A, 2018, 725: 530-540.
[2]Ceschini Lorella, Morri Alessandro, Morri Andrea. Effects of the delay between quenching and aging on hardness and tensile properties of A356 aluminum alloy[J]. Journal of Materials Engineering and Performance, 2013, 22(1): 200-205.
[3]郑秋菊, 叶中飞, 江鸿翔, 等. 微合金化元素La对亚共晶Al-Si合金凝固组织与力学性能的影响[J]. 金属学报, 2021, 57(1): 103-110.
Zheng Qiuju, Ye Zhongfei, Jiang Hongxiang, et al. Effect of microalloying element La on solidification microstructure and mechanical properties of hypoeutectic Al-Si alloys[J]. Acta Metallurgica Sinica, 2021, 57(1): 103-110.
[4]王会阳, 安云岐, 李承宇, 等. 稀土在铝和铝合金中应用的研究及进展[J]. 稀土, 2012, 33(1): 74-80.
Wang Huiyang, An Yunqi, Li Chengyu, et al. The research progress of rare earth application in aluminum and aluminum alloys[J]. Chinese Rare Earths, 2012, 33(1): 74-80.
[5]张启运, 郑朝贵, 韩万书. 稀土元素对Al-Si共晶合金的变质作用[J]. 金属学报, 1981, 17(2): 130-136, 240-241.
Zhang Qiyun, Zheng Chaogui, Han Wanshu. The modification of Al-Si eutectic alloys with rare-earth elements[J]. Acta Metallurgica Sinica, 1981, 17(2): 130-136, 240-241.
[6]余聪, 陈乐平, 周全. 稀土元素对铝合金组织与性能影响的研究进展[J]. 特种铸造及有色合金, 2021, 41(2): 241-246.
Yu Cong, Chen Leping, Zhou Quan. Research progress in effects of rare earth elements on microstructure and properties of aluminum alloy[J]. Special Casting and Nonferrous Alloys, 2021, 41(2): 241-246.
[7]Zhang X W, Yang Y, Jin H N, et al. Effect of lanthanum content on microstructure and mechanical properties of Al-5Mg-2Si-0.6Mn alloy in squeeze casting[J]. Journal of Materials Research and Technology, 2021, 15: 6025-6033.
[8]Li Z, Yan H. Modification of primary α-Al, eutectic silicon and β-Al5FeSi phases in as-cast AlSi10Cu3 alloys with (La+Yb) addition[J]. Journal of Rare Earths, 2015, 33(9): 995-1003.
[9]Shi Y T, Wang Q, Zhao G. Effects of Gd and Ho modification on microstructure of Al-Si-Mg cast aluminum alloy[J]. Chinese Rare Earths, 2013, 34(2): 47-51.
[10]Gao Z, Li H, Lai Y, et al. Effects of minor Zr and Er on microstructure and mechanical properties of pure aluminum[J]. Materials Science and Engineering A, 2013, 580: 92-98.
[11]Lin G Y, Kun L I, Feng D, et al. Effects of La-Ce addition on microstructure and mechanical properties of Al-18Si-4Cu-0.5Mg alloy[J]. Transactions of Nonferrous Metals Society of China, 2019, 29(8): 1592-1600.
[12]Zhu M Z, Jian Y, Yao L, et al. Effect of mischmetal modification treatment on the microstructure tensile properties and fracture behavior of Al-7.0%Si-0.3%Mg foundry aluminum alloys[J]. Journal of Materials Science, 2011, 46(8): 2685-2694.
[13]Tsai Y C, Chou C Y, Lee S L, et al. Effect of trace La addition on the microstructures and mechanical properties of A356 (Al-7Si-0.35Mg) aluminum alloys[J]. Journal of Alloys and Compounds, 2009, 487: 157-162.
[14]Tsai Y C, Lee S L, Lin C K. Effect of trace Ce addition on the microstructures and mechanical properties of A356 (Al-7Si-0.35Mg) aluminum alloys[J]. Journal of the Chinese Institute of Engineers, 2011, 34(5): 609-616.
[15]Tsai Y C, Chou C Y, Jeng R R, et al. Effect of rare earth elements addition on microstructures and mechanical properties of A356 alloy[J]. International Journal of Cast Metals Research, 2011, 24(2): 83-87.
[16]Shi Z M, Wang Q, Zhao G, et al. Effects of erbium modification on the microstructure and mechanical properties of A356 aluminum alloys[J]. Materials Science and Engineering A, 2015, 626: 102-107.
[17]Shi Z M, Wang Q, Shi Y T, et al. Microstructure and mechanical properties of Gd-modified A356 aluminum alloys[J]. Rare Earths, 2015, 33: 1004-1009.
[18]Wang Q, Shi Z M, Li H, et al. Effects of holmium additions on microstructure and properties of A356 aluminum alloys[J]. Metals, 2018, 8(10): 849-861.
[19]中山大学金属系. 稀土物理化学常数[M]. 北京: 冶金工业出版社, 1978.
[20]周公度, 段连运. 结构化学基础[M]. 北京: 北京大学出版社, 2008.
[21]孙伟成, 张淑荣, 侯爱芹. 稀土在铝合金中的行为[M]. 北京: 兵器工业出版社, 1992.
[22]刘文祎, 徐聪, 刘茂文, 等. 稀土元素Gd对Al-Si-Mg铸造合金微观组织和力学性能的影响[J]. 材料工程, 2019, 47(6): 129-135.
Liu Wenwei, Xu Cong, Liu Maowen, et al. Effect of rare earth element Gd on microstructure and mechanical properties of Al-Si-Mg cast alloy[J]. Journal of Materials Engineering, 2019, 47(6): 129-135.
[23]Samuel A M, Doty H W, Valtierra S, et al. Intermetallic precipitation in rare earth-treated A413.1 alloy: A metallographic study[J]. International Journal of Materials Research, 2018, 109(2): 157-171.

轻-重稀土混合添加对Al-Si-Mg合金显微组织和力学性能的影响

Effect of mixed addition of light and heavy rare earth elements on microstructure and mechanical properties of Al-Si-Mg alloy

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	高玉魁, 方文奕. 碳含量与热处理对高铌钛铝合金微观组织及力学性能的影响[J]. 金属热处理, 2024, 49(8): 9-14.
[2]	张宏亮, 周春波, 侯燕, 蒋志强. C-Si-Mn系配分钢的研究进展[J]. 金属热处理, 2024, 49(8): 22-30.
[3]	曹悦, 高雪云, 王海燕, 邢磊, 林鸿亮. 稀土La对含Cu马氏体不锈钢显微组织与力学性能的影响[J]. 金属热处理, 2024, 49(8): 42-47.
[4]	白瑞, 杜云飞, 贺秀丽, 梁红玉. Al含量对高锰高铝轻质钢组织和力学性能的影响[J]. 金属热处理, 2024, 49(8): 48-52.
[5]	徐超, 曹欣旺, 王晨阳, 王玉婷, 张倩, 杨其全, 胡杰. 热处理工艺对高速列车用51CrV4钢轴箱弹簧力学性能及服役性能的影响[J]. 金属热处理, 2024, 49(8): 53-59.
[6]	华文娟, 张建勋. 时效处理对电弧熔丝增材制造2319铝合金性能及断裂行为的影响[J]. 金属热处理, 2024, 49(8): 60-66.
[7]	王堤鹤, 庞启航, 赵星宇, 李维娟, 赵立冬, 史津铭. IQ&P工艺处理高强钢的组织性能及低温C配分[J]. 金属热处理, 2024, 49(8): 74-81.
[8]	王春兴, 李明. 退火处理对CoCrFeNiMn高熵合金组织和性能的影响[J]. 金属热处理, 2024, 49(8): 102-107.
[9]	任云飞, 潘新元, 万天剑, 李景辉, 张明亚. T6热处理对高压压铸ADC12铝合金微观结构和性能的影响[J]. 金属热处理, 2024, 49(8): 108-112.
[10]	迟蕊, 徐志远, 孟双, 李延成, 徐扬帆, 李涛. 中间退火温度对6016铝合金组织及性能的影响[J]. 金属热处理, 2024, 49(8): 113-118.
[11]	徐锋, 孙强, 孟吉炜. 固溶温度对超低碳15-5PH沉淀硬化不锈钢组织和性能的影响[J]. 金属热处理, 2024, 49(8): 124-129.
[12]	张勇, 李如杨, 马青山, 胡效东. 热处理对09MnNiDR低温钢焊接接头组织及力学性能的影响[J]. 金属热处理, 2024, 49(8): 136-142.
[13]	刘晨希, 胡昕明, 欧阳鑫, 邢梦楠, 白云峰. 回火时间对低焊接裂纹敏感性压力容器用钢组织性能的影响[J]. 金属热处理, 2024, 49(8): 143-146.
[14]	曲之国, 张万新, 白学飞, 王东明, 张友建. 模拟焊后热处理对厚规格16MnDR钢板组织性能的影响[J]. 金属热处理, 2024, 49(8): 147-151.
[15]	孙昭琦, 李涛, 韩强, 张行刚, 白岩松, 高志敏. 淬火工艺对28MnCrMoRE油井管钢显微组织及硬度的影响[J]. 金属热处理, 2024, 49(8): 160-164.