4Cr5Mo2V热作模具钢的CCT曲线及碳化物沿晶析出温度测定

doi:10.13251/j.issn.0254-6051.2024.09.012

金属热处理 ›› 2024, Vol. 49 ›› Issue (9): 72-79.DOI: 10.13251/j.issn.0254-6051.2024.09.012

4Cr5Mo2V热作模具钢的CCT曲线及碳化物沿晶析出温度测定

高兴成, 吴博雅, 吴晓春

上海大学材料科学与工程学院省部共建高品质特殊钢冶金与制备国家重点实验室,上海 200072

收稿日期:2024-03-06 修回日期:2024-07-02 出版日期:2024-09-25 发布日期:2024-10-29
通讯作者: 吴晓春,博士生导师,教授,E-mail: xcwu@ staff.shu.edu.cn
作者简介:高兴成(1996—),男,硕士研究生,主要研究方向为热作模具钢的组织性能,E-mail: h18851400707@163.com。
基金资助:
省部共建高品质特殊钢冶金与制备国家重点实验室自主课题(SKLASS 2022-Z12)

Measurement of CCT curves and carbide intergranular precipitation temperature of 4Cr5Mo2V hot-working die steel

Gao Xingcheng, Wu Boya, Wu Xiaochun

State Key Laboratory of Advanced Special Steel, School of Materials Science and Engineering, Shanghai University, Shanghai 200072, China

Received:2024-03-06 Revised:2024-07-02 Online:2024-09-25 Published:2024-10-29

摘要/Abstract

摘要： 通过热膨胀仪、电阻仪和硬度计,结合扫描电镜和能谱仪,对不同冷速下4Cr5Mo2V钢的组织和硬度进行表征,绘制CCT曲线,并对钢中碳化物沿晶析出温度进行了测定。结果表明,随着冷却速度的降低,硬度降低,组织依次转变为马氏体、贝氏体和珠光体,珠光体和贝氏体转变临界冷却速度分别为0.015 ℃/s和0.25 ℃/s;冷却速度不大于0.25 ℃/s时,钢中有碳化物沿晶析出,且随冷却速度降低,碳化物沿晶析出温度升高,0.01 ℃/s冷却速度下,析出温度最高为1022 ℃。

关键词: 4Cr5Mo2V热作模具钢, 冷却速度, CCT曲线, 沿晶碳化物, 析出温度

Abstract: Microstructure and hardness of 4Cr5Mo2V steel at different cooling rates were observed and measured by using thermal expansion meter, resistance meter and hardness tester, combined with scanning electron microscope and energy dispersive spectroscopy. CCT curves of the tested steel were plotted, and the temperature of carbide intergranular precipitation in the steel was determined. The results show that as the cooling rate decreases, the hardness decreases and the microstructure transforms into martensite, bainite and pearlite in sequence. The critical cooling rates for pearlite and bainite transformation are 0.015 ℃/s and 0.25 ℃/s, respectively. When the cooling rate is not greater than 0.25 ℃/s, carbides precipitate along the grain in the steel, and as the cooling rate decreases, the temperature of carbide precipitation along the grain increases. At a cooling rate of 0.01 ℃/s, the highest precipitation temperature is 1022 ℃.

Key words: 4Cr5Mo2V hot-working die steel, cooling rate, CCT curve, intergranular carbides, precipitation temperature

中图分类号:

TG142.7

高兴成, 吴博雅, 吴晓春. 4Cr5Mo2V热作模具钢的CCT曲线及碳化物沿晶析出温度测定[J]. 金属热处理, 2024, 49(9): 72-79.

Gao Xingcheng, Wu Boya, Wu Xiaochun. Measurement of CCT curves and carbide intergranular precipitation temperature of 4Cr5Mo2V hot-working die steel[J]. Heat Treatment of Metals, 2024, 49(9): 72-79.

参考文献

[1]Kang J H, Park I W, Jae J S, et al. A study on die wear model of warm and hot forgings[J]. Metals and Materials, 1998, 4(3): 477-483.
[2]Ebara R. Fatigue crack initiation and propagation behavior of forging die steels[J]. International Journal of Fatigue, 2010, 32(5): 830-840.
[3]白嘉远. 铝合金材料的应用及其加工成形技术[J]. 世界有色金属, 2017(14): 272-273.
Bai Jiayuan. Application of aluminum alloy material and its forming technology[J]. World Nonferrous Metals, 2017(14): 272-273.
[4]王春涛, 姚杰. 压铸铝合金的研究进展[J]. 模具工业, 2019, 45(8): 1-5.
Wang Chuntao, Yao Jie. Research progress of die casting aluminum alloy[J]. Mould Industry, 2019, 45(8): 1-5.
[5]岛村祐太, 舘幸生, 中間一夫, 等. 合金元素对热作模具钢高温强度的影响及新型压铸模用钢的研制[J]. 于红, 译. 模具制造, 2021, 21(12): 84-89.
[6]宋雯雯, 闵永安, 吴晓春. 热作模具钢SDH8与H13的强韧性对比研究[J]. 金属热处理, 2008, 33(9): 59-61.
Song Wenwen, Min Yongan, Wu Xiaochun. Comparative studies on strength and toughness of SDH8 and H13 hot work steel[J]. Heat Treatment of Metals, 2008, 33(9): 59-61.
[7]赵成志, 金天文, 符策鹄, 等. 预处理工艺对热作模具钢5Cr8MoNi2SiV组织与硬度的影响[J]. 金属热处理, 2016, 41(1): 29-34.
Zhao Chengzhi, Jin Tianwen, Fu Cehu, et al. Influence of pretreatment process on microstructure and hardness of hot-work die steel 5Cr8MoNi2SiV[J]. Heat Treatment of Metals, 2016, 41(1): 29-34.
[8]吴远辉, 左鹏鹏, 白植雄, 等. 淬回火工艺对压铸模具钢4Cr5Mo2V强韧性及组织影响[J]. 模具制造, 2017, 17(6): 93-97.
Wu Yuanhui, Zuo Pengpeng, Bai Zhixiong, et al. Effect of quenching and tempering process on strength, toughness and microstructure of die-casting die steel 4Cr5Mo2V[J]. Die and Mould Manufacture, 2017, 17(6): 93-97.
[9]张学友, 左鹏鹏, 何西娟, 等. 氮含量对热作模具钢4Cr5Mo2V热疲劳性能的影响[J]. 金属热处理, 2017, 42(1): 9-14.
Zhang Xueyou, Zuo Pengpeng, He Xijuan, et al. Effect of nitrogen content on thermal fatigue property of hot work die steel 4Cr5Mo2V[J]. Heat Treatment of Metals, 2017, 42(1): 9-14.
[10]林鹏, 马党参, 胡连新, 等. 压铸用模具钢4Cr5Mo2V的过冷奥氏体连续冷却转变[J]. 金属热处理, 2018, 43(6): 16-20.
Lin Peng, Ma Dangshen, Hu Lianxin, et al. Continuous cooling transformation of super-cooled austenite of die steel 4Cr5Mo2V for die-casting[J]. Heat Treatment of Metals, 2018, 43(6): 16-20.
[11]李红英, 王法云, 曾翠婷, 等. 3Cr2Mo钢CCT曲线的测定与分析[J]. 中南大学学报, 2011, 42(7): 1928-1933.
Li Hongying, Wang Fayun, Zeng Cuiting, et al. Determination and analysis of CCT curves of 3Cr2Mo steel[J]. Journal of Central South University, 2011, 42(7): 1928-1933.
[12]张进峰. 中低碳钢碳扩散行为的电阻和内耗方法研究[D]. 上海: 上海大学, 2021.
Zhang Jingfeng. Study on carbon diffusion behaviors of medium and low carbon steels by resistance and internal friction methods[D]. Shanghai: Shanghai University, 2021.
[13]Park B J, Choi J M, Lee K J. Analysis of phase transformations during continuous cooling by the first derivative of dilatation in low carbon steels[J]. Materials Characterization, 2012, 64: 8-14.
[14]邹仲平, 路峰, 于浩, 等. 50Mn2V 钢连铸坯CCT曲线测定及热塑性分析研究[J]. 热加工工艺, 2019, 48(2): 76-80, 86.
Zou Zhongping, Lu Feng, Yu Hao, et al. Research on determination of CCT curve and thermoplastic analysis of 50Mn2V steel continuous casting billet[J]. Hot Working Technology, 2019, 48(2): 76-80, 86.
[15]曹瑞芳, 王福明, 李长荣, 等. Mo对R5系泊链钢过冷奥氏体连续冷却转变曲线[J]. 金属热处理, 2010, 35(5): 6-10.
Cao Ruifang, Wang Fuming, Li Changrong, et al. Effect of Mo on austenite continuous cooling transformation curves of R5 off shore mooring chain steel[J]. Heat Treatment of Metals, 2010, 35(5): 6-10.
[16]Krielaart G P, Zwaag S V. Simulations of pro-eutectoid ferrite formation using a mixed control growth model[J]. Materials Science and Engineering A, 1998, 246(1/2): 104-116.
[17]Donachie S J, Ansell G S. The effect of quench rate on the properties and morphology of ferrous martensite[J]. Metallurgical Transactions A, 1975, 6(10): 1863-1875.

4Cr5Mo2V热作模具钢的CCT曲线及碳化物沿晶析出温度测定

Measurement of CCT curves and carbide intergranular precipitation temperature of 4Cr5Mo2V hot-working die steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	袁静, 陈飞达, 钟海清, 唐小勇, 朱映玉, 冷烨旻, 肖虎, 田世伟. XGTC300L搪瓷钢的连续冷却转变行为与析出规律[J]. 金属热处理, 2024, 49(9): 80-85.
[2]	黄剑涛, 张明赫, 冯运莉, 尹绍江, 陈春生, 王厚昕. V-Nb微合金化Q420B大规格角钢的连续冷却转变规律[J]. 金属热处理, 2024, 49(7): 121-127.
[3]	陈作宁, 师仲然, 胡骞, 展之德, 罗小兵. 390 MPa级抗碰撞船体钢的奥氏体连续冷却转变[J]. 金属热处理, 2024, 49(7): 146-151.
[4]	董丽丽, 崔成波, 袁晓鸣, 刘泽田. BTP500钢板过冷奥氏体连续冷却转变行为[J]. 金属热处理, 2024, 49(7): 157-160.
[5]	郭大勇, 高航, 潘阳, 宫文赫, 王秉喜, 杨迎强. 基于碳偏析指数的高碳钢盘条网状渗碳体控制技术[J]. 金属热处理, 2024, 49(7): 287-293.
[6]	刘阳, 高茗, 马莉, 胡祯, 孙中梅, 张士震. 低成本无钒热轧钢筋HRB400E的生产工艺优化[J]. 金属热处理, 2024, 49(7): 294-300.
[7]	王凯明, 姜芙林, 卜善飞, 王超, 姜志勇, 刘庆玉. 液氮辅助激光熔覆温度场仿真及熔覆层摩擦磨损性能分析[J]. 金属热处理, 2024, 49(6): 239-247.
[8]	刘干, 孔祥磊, 黄明浩, 王杨, 张英慧. 冷却速率对超高强度X90M管线钢相变行为的影响[J]. 金属热处理, 2024, 49(5): 162-167.
[9]	黄东, 蒋义然. S355低合金结构钢的动态连续冷却转变曲线及力学性能[J]. 金属热处理, 2024, 49(4): 38-41.
[10]	童炀, 张婧, 辛文彬, 罗果萍, 彭军, 侯蹬云. Nb含量对V-Ti-N工程结构用钢连续冷却转变规律及组织性能的影响[J]. 金属热处理, 2024, 49(3): 236-243.
[11]	曹佳丽, 靳红泽, 李康立, 徐亚鹏, 赵强, 王翠萍, 李梦楠. 水电用Q690CFD低合金高强钢SH-CCT曲线测定与分析[J]. 金属热处理, 2024, 49(2): 60-65.
[12]	李忠波, 袁清, 许少普, 张涛, 陈熙, 莫家璇, 任杰. 超厚规格模具钢3Cr2Mo不同冷速下的硬度和组织差异[J]. 金属热处理, 2024, 49(1): 31-38.
[13]	鄢文泽, 闫文青, 林轩艺, 王红鸿. 铌微合金化对低合金高强钢模拟焊接热影响区粒状贝氏体相变及SH-CCT曲线的影响[J]. 金属热处理, 2023, 48(9): 150-156.
[14]	孙晓冉, 王程明, 赵楠, 白丽娟, 郑文跃. 4330-Nb抽油杆用钢的连续冷却转变特性分析[J]. 金属热处理, 2023, 48(8): 42-46.
[15]	郭亚非, 李志龙, 张博, 李洁, 庞庆海. Cr8支承辊用钢的连续冷却过程相变行为[J]. 金属热处理, 2023, 48(8): 47-51.