淬火介质对离子渗氮42CrMo钢冲击性能的影响

doi:10.13251/j.issn.0254-6051.2024.10.009

金属热处理 ›› 2024, Vol. 49 ›› Issue (10): 59-65.DOI: 10.13251/j.issn.0254-6051.2024.10.009

淬火介质对离子渗氮42CrMo钢冲击性能的影响

陈治¹, 李宝奎², 江鹏³, 卢金生¹, 师陆冰^1,4, 冯叶¹, 何潇¹

1.郑机所(郑州)传动科技有限公司, 河南郑州 450001;
2.中国机械总院集团云南分院有限公司, 云南昆明 650031;
3.北京特种工程设计研究院, 北京 100028;
4.哈尔滨工业大学金属精密热加工国家级重点实验室, 黑龙江哈尔滨 150001

收稿日期:2024-05-13 修回日期:2024-08-06 出版日期:2024-11-28 发布日期:2024-11-28
通讯作者: 师陆冰,高级工程师,E-mail:shilubing91@163.com
作者简介:陈治(1995—),男,硕士,主要研究方向为齿轮材料及热处理工艺,E-mail:chenzhi1107@163.com。
基金资助:
国防基础科研计划 (JCKYS2024603C008)

Effect of quenching media on impact property of ion-nitrided 42CrMo steel

Chen Zhi¹, Li Baokui², Jiang Peng³, Lu Jinsheng¹, Shi Lubing^1,4, Feng Ye¹, He Xiao¹

1. ZRIME Gearing Technology Co., Ltd., Zhengzhou Henan 450001, China;
2. CAM-Yunnan Machinery Research and Design Institute, Kunming Yunnan 650031, China;
3. Beijing Special Engineering Design Institute, Beijing 100028, China;
4. National Key Laboratory for Precision Hot Processing of Metals, Harbin Institute of Technology, Harbin Heilongjiang 150001, China

Received:2024-05-13 Revised:2024-08-06 Online:2024-11-28 Published:2024-11-28

摘要/Abstract

摘要： 为研究淬火介质对42CrMo钢离子渗氮后的组织与冲击性能的影响,分别用PAG水基淬火液和淬火油两种介质对42CrMo钢进行调质处理(850 ℃×1 h淬火+580 ℃×1.5 h回火),然后进行540 ℃×60 h离子渗氮,利用光学显微镜(OM)、扫描电镜(SEM)、拉伸试验、冲击试验、显微硬度计等研究了42CrMo钢渗氮前后的组织与强韧性。结果表明,采用PAG水基淬火液淬火后42CrMo钢的组织为全马氏体,而经油淬后的组织为马氏体+下贝氏体;两种淬火介质下的调质态组织均为细小均匀的回火索氏体;离子渗氮后,采用PAG水基淬火液时42CrMo钢的渗氮层较油淬时更深,心部基体组织与调质态相差不大,而油淬的心部基体组织中出现比较明显的游离铁素体;油淬42CrMo钢调质态的-20 ℃冲击吸收能量较高,而PAG水基淬火液淬火的42CrMo钢渗氮后的-20 ℃冲击吸收能量更高,比油淬试样高13.8%。

关键词: 离子渗氮, 调质处理, 冲击性能, 淬火介质

Abstract: In order to investigate the effect of quenching media on microstructure and impact property of the ion-nitrided 42CrMo steel, PAG aqueous solution and quenching oil was used respectively for quenching at 850 ℃ for 1 h and tempering at 580 ℃ for 1.5 h, and then ion-nitriding at 540 ℃ for 60 h was carried out. The microstructure, strength and toughness before and after ion-nitriding were studied by means of optical microscope (OM), scanning electron microscope (SEM), tensile test, impact test and microhardness tester. The results show that the microstructure of the 42CrMo steel is all martensite after quenching with PAG aqueous solution, while the oil quenched microstructure is a mixture of martensite and lower bainite, however, both of the microstructure of the steel after quenching and tempering with two quenching medias is fine and uniform tempered sorbite. After ion-nitriding, the nitriding layer of the 42CrMo steel with PAG aqueous solution quenching is thicker than that with oil quenching, and the microstructure at the core is not different from that after quenching and tempering, while the microstructure at the core of that with oil quenching shows obvious free ferrite. The impact absorbed energy at -20 ℃ of the 42CrMo steel after quenching and tempering with oil quenching is higher, while the impact absorbed energy at -20 ℃ of the nitrided 42CrMo steel with PAG aqueous solution is 13.8% higher than that with oil quenching.

Key words: ion-nitriding, quenching and tempering, impact property, quenching media

中图分类号:

TG156.8⁺2

陈治, 李宝奎, 江鹏, 卢金生, 师陆冰, 冯叶, 何潇. 淬火介质对离子渗氮42CrMo钢冲击性能的影响[J]. 金属热处理, 2024, 49(10): 59-65.

Chen Zhi, Li Baokui, Jiang Peng, Lu Jinsheng, Shi Lubing, Feng Ye, He Xiao. Effect of quenching media on impact property of ion-nitrided 42CrMo steel[J]. Heat Treatment of Metals, 2024, 49(10): 59-65.

参考文献

[1]陈永祥, 李勇, 王涛, 等. 42CrMo钢齿圈的锻后热处理工艺[J]. 金属热处理, 2023, 48(11): 245-249.
Chen Yongxiang, Li Yong, Wang Tao, et al. Heat treatment processes of 42CrMo steel gear ring after forging[J]. Heat Treatment of Metals, 2023, 48(11): 245-249.
[2]陈海, 崔鼎. 42CrMo钢稀土微合金化对气体渗氮性能的影响[J]. 金属热处理, 2023, 48(9): 180-182.
Chen Hai, Cui Ding. Effect of rare earth microalloying on gas nitriding properties of 42CrMo steel[J]. Heat Treatment of Metals, 2023, 48(9): 180-182.
[3]卢金生, 李宝奎. 齿轮的精密热处理及抗疲劳制造探讨[J]. 机械传动, 2019, 43(3): 170-175.
Lu Jinsheng, Li Baokui. Discussion of precision heat treatment and anti-fatigue manufacturing of gear[J]. Journal of Mechanical Transmission, 2019, 43(3): 170-175.
[4]李双喜, 陈琳, 汪美桃, 等. 预氧化+稀土铈对42CrMo钢离子渗氮的影响[J]. 金属热处理, 2021, 46(5): 186-189.
Li Shuangxi, Chen Lin, Wang Meitao, et al. Effect of pre-oxidation and rare earth cerium on plasma nitriding of 42CrMo steel[J]. Heat Treatment of Metals, 2021, 46(5): 186-189.
[5]徐祺昊, 杨礼林, 夏明, 等. 38CrMoAlA钢传动主轴失效分析[J]. 金属热处理, 2021, 46(9): 268-272.
Xu Qihao, Yang Lilin, Xia Ming, et al. Failure analysis of 38CrMoAlA steel driveshaft[J]. Heat Treatment of Metals, 2021, 46(9): 268-272.
[6]杨耀军, 李蕊轩, 田林海, 等. 锁紧轴断裂失效分析[J]. 热加工工艺, 2015, 44(12): 239-241.
Yang Yaojun, Li Xinxuan, Tian Linhai, et al. Failure analysis of lock shaft fracture[J]. Hot Working Technology, 2015, 44(12): 239-241.
[7]赵燕平, 闫爱淑, 郭文荣. 35CrMo钢渗前组织对气体氮化层组织和性能影响的研究[C]//全国复合材料学术会议, 2002.
[8]张文, 朱百智, 黄振建, 等. 淬火介质对42CrMo钢棒淬火组织及硬度影响的数值模拟及试验验证[J]. 金属热处理, 2020, 45(1): 56-60.
Zhang Wen, Zhu Baizhi, Huang Zhenjian, et al. Numerical simulation and experimental verification of effect of quenching medium on quenching microstructure and hardness of 42CrMo steel rod[J]. Heat Treatment of Metals, 2020, 45(1): 56-60.
[9]齐羿, 杨建全, 焦斐. 合金钢连杆在不同冷却介质中淬火后的组织与性能[J]. 金属热处理, 2023, 48(8): 64-71.
Qi Yi, Yang Jianquan, Jiao Fei. Microstructure and properties of alloy steel connecting rod quenched in different quenching media[J]. Heat Treatment of Metals, 2023, 48(8): 64-71.
[10]毕明龙, 刘金玲, 曹娜娜, 等. 渗氮温度对G13Cr4Mo4Ni4V钢渗氮层组织和性能的影响[J]. 轴承, 2020(11): 29-33.
Bi Minglong, Liu Jinling, Cao Nana, et al. Effects of nitriding temperature on microstructure and properties of nitriding layer of G13Cr4Mo4Ni4V steel[J]. Bearing, 2020(11): 29-33.
[11]刘建睿, 严宏志, 李算, 等. 离子渗氮工艺参数对4Cr5MoSiV钢表层组织与性能的影响[J]. 表面技术, 2019, 48(8): 199-205.
Liu Jianrui, Yan Hongzhi, Li Suan, et al. Effect of ion nitriding process parameters on surface properties of 4Cr5MoSiV steel[J]. Surface Technology, 2019, 48(8): 199-205.
[12]崔崑. 钢的成分、组织与性能第一分册: 合金钢基础[M]. 北京: 科学出版社, 2019: 323.
[13]Fu H, Zhang J, Huang J, et al. Effect of temperature on microstructure, corrosion resistance, and toughness of salt bath nitrided tool steel[J]. Journal of Materials Engineering and Performance, 2016, 25: 3-8.
[14]刘铭杰, 周为群, 董瀚, 等. 回火温度对含钒42CrMo钢-40 ℃冲击韧性的影响[J]. 上海金属, 2023, 45(4): 62-70.
Liu Mingjie, Zhou Weiqun, Dong Han, et al. Effect of tempering temperatures on impact toughness of vanadium-containing 42CrMo steel at -40 ℃[J]. Shanghai Metals, 2023, 45(4): 62-70.
[15]陈俊丹, 莫文林, 王培, 等. 回火温度对42CrMo钢冲击韧性的影响[J]. 金属学报, 2012, 48(10): 1186-1193.
Chen Jundan, Mo Wenlin, Wang Pei, et al. Effects of tempering temperature on the impact toughness of steel 42CrMo[J]. Acta Metallurgica Sinica, 2012, 48(10): 1186-1193.
[16]张守清, 胡小锋, 杜瑜宾, 等. 淬火冷却速率对海洋平台用Ni-Cr-Mo-B钢性能的影响[J]. 材料研究学报, 2022, 36(4): 250-260.
Zhang Shouqing, Hu Xiaofeng, Du Yubin, et al. Effect of quenching cooling rate on mechanical properties of a Ni-Cr-Mo-B steel for offshore platform[J]. Chinese Journal of Materials Research, 2022, 36(4): 250-260.
[17]Solodkin G A, Tsyrlin É S, Ratgauz L Y. Impact strength of nitrided steels[J]. Metal Science and Heat Treatment, 1991, 33(1): 20-23.
[18]Genel K, Demirkol M, Capa M. Effect of ion nitriding on fatigue behaviour of AISI 4140 steel[J]. Materials Science and Engineering A, 2000, 279(1/2): 207-216.

淬火介质对离子渗氮42CrMo钢冲击性能的影响

Effect of quenching media on impact property of ion-nitrided 42CrMo steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	王秉楠, 贾玉鑫, 王姗姗, 张亚辉. 高淬透性高碳铬轴承钢的组织与性能[J]. 金属热处理, 2024, 49(9): 31-35.
[2]	陈琳, 李子岩, 白小波, 李双喜. 小模数地铁联轴器的离子渗氮工艺[J]. 金属热处理, 2024, 49(9): 209-215.
[3]	李峰. 钛改性离子渗氮处理对沉淀硬化钢性能的影响[J]. 金属热处理, 2024, 49(8): 183-188.
[4]	李子岩, 崔宇, 许鸿翔, 王新华, 赵少甫, 郭敬强, 陈生超. 调质工艺优化对ZG34CrNiMo钢组织和低温冲击性能的影响[J]. 金属热处理, 2024, 49(7): 220-224.
[5]	李双喜, 沈亚秋, 白小波, 高洁, 陈琳. 炉压对齿轮离子渗氮的影响[J]. 金属热处理, 2024, 49(6): 129-134.
[6]	蒲博闻, 刘玉婷, 王延荣, 刁占英, 何敬卫. 调质处理对34CrNiMo6钢连杆锻件组织与硬度的影响[J]. 金属热处理, 2024, 49(5): 173-178.
[7]	王树梁, 王春光, 李爱菊, 王雪兆. 固溶工艺对Mg-7.5Gd-3Y-0.5Zr合金微观组织及动态冲击行为的影响[J]. 金属热处理, 2024, 49(4): 186-194.
[8]	樊朋煜, 翟鹏远, 刘克, 李国栋, 吴玉广, 李峰诚, 邹伟. 不同淬火油对18Cr2Ni2MoVNbA钢渗碳淬火组织和变形影响规律的数值模拟[J]. 金属热处理, 2024, 49(4): 229-236.
[9]	胡昂, 吴润, 李忠波, 吴腾. 亚温淬火对低合金耐磨钢增韧及性能的影响[J]. 金属热处理, 2024, 49(3): 22-27.
[10]	杜云飞, 白瑞, 吴璞, 张亚琴. PCrNi3MoV高强钢带状组织在调质工艺中的显微特征[J]. 金属热处理, 2024, 49(3): 135-140.
[11]	张碧清, 韩啸, 贺瑞军, 朱硕, 王赟, 郭凯宇. 基于灰色关联度分析的不锈钢离子渗氮层对磨损性能的影响[J]. 金属热处理, 2024, 49(3): 174-181.
[12]	杜昭阳, 赵杰, 陈献刚, 曹铁山. 淬火工艺对DH350模具钢组织和力学性能的影响[J]. 金属热处理, 2024, 49(2): 16-24.
[13]	胡启文, 李天怡, 耿笑笑, 成卓, 刘文月, 吴桂林. 退火工艺对Fe-30Mn-10Al-1C低密度钢组织与性能的影响[J]. 金属热处理, 2024, 49(2): 91-97.
[14]	李铖, 彭其春, 童志博, 梁亮, 齐江华, 肖爱达, 董常福. 不同热处理工艺对9Ni低温容器用钢组织与性能的影响[J]. 金属热处理, 2024, 49(2): 98-103.
[15]	周琮, 陈献刚, 曹铁山, 赵杰. 调质工艺对Cr-Ni-Mo-V超高强韧钢组织和力学性能的影响[J]. 金属热处理, 2024, 49(2): 135-141.