贝氏体等温温度对两相区轧制舰船用钢组织性能的影响

doi:10.13251/j.issn.0254-6051.2024.11.025

金属热处理 ›› 2024, Vol. 49 ›› Issue (11): 167-171.DOI: 10.13251/j.issn.0254-6051.2024.11.025

贝氏体等温温度对两相区轧制舰船用钢组织性能的影响

田亚强, 姚硕, 张明山, 李红斌, 胡宝佳, 陈连生

华北理工大学教育部现代冶金技术重点试验室, 河北唐山 063210

收稿日期:2024-06-03 修回日期:2024-09-12 出版日期:2024-11-25 发布日期:2025-01-09
通讯作者: 张明山,讲师,博士,E-mail:zhangms@ncst.edu.cn
作者简介:田亚强(1980—),男,教授,博士,主要研究方向为金属材料组织性能控制及强韧化,E-mail:tyqwylfive@163.com。
基金资助:
河北省自然科学基金重点项目(E2022209049)

Effect of isothermal bainite temperature on microstructure and properties of ship steel after intercritical rolling

Tian Yaqiang, Yao Shuo, Zhang Mingshan, Li Hongbin, Hu Baojia, Chen Liansheng

Key Laboratory of the Ministry of Education for Modern Metallurgical Technology, North China University of Science and Technology, Tangshan Hebei 063210, China

Received:2024-06-03 Revised:2024-09-12 Online:2024-11-25 Published:2025-01-09

摘要/Abstract

摘要： 采用扫描电镜(SEM)、X射线衍射仪(XRD)和力学性能测试等手段,研究了两相区轧制后贝氏体区等温温度对舰船用钢组织性能的影响。结果表明,热轧后,试验钢组织为M/A岛和少量铁素体。等温温度为400、450 ℃并空冷至室温时,组织为板条贝氏体、粒状贝氏体和铁素体。等温温度为500 ℃时,组织为粒状贝氏体和铁素体。试验钢经过贝氏体等温处理后,屈服强度在981~1116 MPa之间,抗拉强度在997~1124 MPa之间。在500 ℃等温时,相比其他两种温度,残留奥氏体体积分数最大,导致伸长率和冲击吸收能量分别达到最大值11.7%和104.1 J。综合比较,在450 ℃等温处理时,试验钢的性能达到最佳,抗拉强度为1124 MPa,屈服强度为1116 MPa,伸长率为11.3%,冲击吸收能量为71.4 J。

关键词: 舰船用钢, 两相区轧制, 贝氏体等温处理, 组织, 力学性能

Abstract: Effect of isothermal bainite temperature on microstructure and mechanical properties of ship steel after intercritical rolling was investigated by means of scanning electron microscope (SEM), X-ray diffractometer (XRD) and mechanical properties tests. The results show that the microstructure is M/A island and a small amount of ferrite after hot rolling. When the isothermal temperature is 400 ℃ and 450 ℃ followed by air cooling, the microstructure is composed of the lath bainite, granular bainite and ferrite. When the isothermal temperature is 500 ℃, the microstructure is composed of granular bainite and ferrite. The yield strength of the tested steel ranges from 981 MPa to 1116 MPa, and the tensile strength ranges from 997 MPa to 1124 MPa after bainite isothermal treatment. Compared to the other two isothermal temperatures, the retained austenite volume fraction is the highest when isothermal treated at 500 ℃, resulting in the elongation and impact absorbed energy reaching the maximum values of 11.7% and 104.1 J, respectively. Through comprehensive comparison, the mechanical properties of the steel reaches the optimum when isothermal treated at 450 ℃, with the tensile strength of 1124 MPa, yield strength of 1116 MPa, elongation of 11.3%, and impact absorbed energy of 71.4 J.

Key words: ship steel, intercritical rolling, isothermal bainite treatment, microstructure, mechanical properties

中图分类号:

TG156.1

田亚强, 姚硕, 张明山, 李红斌, 胡宝佳, 陈连生. 贝氏体等温温度对两相区轧制舰船用钢组织性能的影响[J]. 金属热处理, 2024, 49(11): 167-171.

Tian Yaqiang, Yao Shuo, Zhang Mingshan, Li Hongbin, Hu Baojia, Chen Liansheng. Effect of isothermal bainite temperature on microstructure and properties of ship steel after intercritical rolling[J]. Heat Treatment of Metals, 2024, 49(11): 167-171.

参考文献

[1]Han D. High performance steels: Initiative and practice[J]. Science China Technological Sciences, 2012, 55(7): 1774-1790.
[2]狄国标, 刘振宇, 郝利强, 等. 海洋平台用钢的生产现状及发展趋势[J]. 机械工程材料, 2008, 32(8): 1-3.
Di Guobiao, Liu Zhenyu, Hao Liqiang, et al. Present production state and development tendency of offshore platform steels[J]. Materials for Mechanical Engineering, 2008, 32(8): 1-3.
[3]Xie Z J, Fang Y P, Han G, et al. Structure-property relationship in a 960 MPa grade ultrahigh strength low carbon niobium vanadium microalloyed steel: The significance of high frequency induction tempering[J]. Materials Science and Engineering A, 2014, 618: 112-117.
[4]王国栋. 高质量中厚板生产关键共性技术研发现状和前景[J]. 轧钢, 2019, 36(1): 1-8, 30.
Wang Guodong. Status and prospects of research and development of key common technologies for high-quality heavy and medium plate production[J]. Steel Rolling, 2019, 36(1): 1-8, 30.
[5]康永林. 中国中厚板产品生产现状及发展趋势[J]. 中国冶金, 2012, 22(9): 1-4, 14.
Kang Yonglin. Production status and development trend of medium and heavy plate in China[J]. China Metallurgy, 2012, 22(9): 1-4, 14.
[6]黄维, 张志勤, 高真凤, 等. 日本海洋平台用厚板开发现状[J]. 轧钢, 2012, 29(3): 38-42.
Huang Wei, Zhang Zhiqin, Gao Zhenfeng, et al. Development status of steel plate used for offshore platform in Japan[J]. Steel Rolling, 2012, 29(3): 38-42.
[7]Liu Y, Shi L, Liu C, et al. Effect of step quenching on microstructures and mechanical properties of HSLA steel[J]. Materials Science and Engineering A, 2016, 675: 371-378.
[8]朱建业. 中厚板TMCP工艺及其应用进展分析[J]. 山西冶金, 2022, 45(1): 158-159, 162.
Zhu Jianye. Analysis of TMCP process and its application progress of medium and heavy plate[J]. Shanxi Metallurgy, 2022, 45(1): 158-159, 162.
[9]王壮飞. 新一代TMCP工艺下微合金钢组织演变规律与性能研究[D]. 沈阳: 东北大学, 2018.
[10]马国金, 何元春, 董占斌, 等. TMCP工艺冷速对FH40低温船舶用钢组织与性能的影响[J]. 河北冶金, 2022(11): 27-31.
Ma Guojin, He Yuanchun, Dong Zhanbin, et al. Effect of cooling rate of TMCP process on microstructure and properties of FH40 low temperature marine steel[J]. Hebei Metallurgy, 2022(11): 27-31.
[11]陈斌, 赵征志, 闫远, 等. 不同贝氏体区等温温度下TRIP钢的组织和性能[J]. 材料热处理学报, 2016, 37(9): 124-128.
Chen Bin, Zhao Zhengzhi, Yan Yuan, et al. Microstructure and properties of TRIP steel under different bainitic isothermal temperatures[J]. Transactions of Materials and Heat Treatment, 2016, 37(9): 124-128.
[12]张海刚, 韩翠红, 李民. 贝氏体等温温度对TRIP980高强钢微观组织及力学性能的影响[J]. 热加工工艺, 2022, 51(16): 140-142, 148.
Zhang Haigang, Han Cuihong, Li Min, et al. Influence of bainite isothermal temperature on microstructure and mechanical properties of TRIP980 high strength steel[J]. Hot Working Technology, 2022, 51(16): 140-142, 148.
[13]金传伟, 张继明, 吴园园. 针状铁素体X65管线钢中MA岛结构表征及其对疲劳裂纹扩展的影响[J]. 材料热处理学报, 2023, 44(6): 143-149.
Jin Chuanwei, Zhang Jiming, Wu Yuanyuan, et al. Characterization of MA islands structure in acicular ferrite X65 pipeline steel and its effect on fatigue crack propagation[J]. Transactions of Materials and Heat Treatment, 2023, 44(6): 143-149.
[14]阮红志, 赵爱民, 赵征志, 等. 高钢级X100管线钢中的M-A岛[J]. 北京科技大学学报, 2013, 35(4): 474-480.
Ruan Hongzhi, Zhao Aimin, Zhao Zhengzhi, et al. M-A islands in high grade X100 pipeline steel[J]. Journal of University of Science and Technology Beijing, 2013, 35(4): 474-480.
[15]田亚强, 张明山, 高天佐, 等. 贝氏体淬火等温温度对低碳硅锰钢组织转变及力学性能影响[J]. 塑性工程学报, 2016, 23(4): 136-140.
Tian Yaqiang, Zhang Mingshan, Gao Tianzuo, et al. Effect of bainitic quenching isothermal temperature on microstructure and mechanical properties of low carbon Si-Mn steel[J]. Journal of Plasticity Engineering, 2016, 23(4): 136-140.
[16]潘红波, 田亚强, 张明山, 等. 低碳硅锰钢奥氏体区形变对贝氏体组织及力学性能影响[J]. 金属热处理, 2017, 42(8): 102-105.
Pan Hongbo, Tian Yaqiang, Zhang Mingshan, et al. Effect of austenite deformation on bainite microstructure and mechanical properties of low carbon Si-Mn steel[J]. Heat Treatment of Metals, 2017, 42(8): 102-105.
[17]程瑄, 桂晓露, 高古辉. 先进高强钢中的残余奥氏体: 综述[J]. 材料导报, 2023, 37(7): 120-131.
Cheng Xuan, Gui Xiaolu, Gao Guhui. Retained austenite in advanced high strength steels: A review[J]. Materials Reports, 2023, 37(7): 120-131.

贝氏体等温温度对两相区轧制舰船用钢组织性能的影响

Effect of isothermal bainite temperature on microstructure and properties of ship steel after intercritical rolling

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	王耐, 马德刚, 李建英, 马光宗, 孙璐, 孙宏亮, 纪明龙. 连续退火对350 MPa级冷轧高耐蚀型耐候钢组织性能的影响[J]. 金属热处理, 2024, 49(9): 18-23.
[2]	田亚强, 么志强, 年保国, 张俊粉, 张晓磊, 宋进英, 张明山, 陈连生. 热轧65Mn带钢等温相变行为及组织性能与扁卷的协同调控[J]. 金属热处理, 2024, 49(9): 24-30.
[3]	周浩, 王帅, 曾燕屏, 马志宝, 周德, 郭德瑞, 董树青. 长时在役Inconel 783高温合金螺栓的显微组织和力学性能[J]. 金属热处理, 2024, 49(9): 36-42.
[4]	张英伟, 白建强, 白占桥, 李炜丽, 谌康, 董树青. P91钢管的长期高温服役组织与性能[J]. 金属热处理, 2024, 49(9): 43-46.
[5]	赵勇桃, 吴银虎, 鲁海涛, 王瑞, 雷丙旺. 不同等温温度下P92钢的组织演变[J]. 金属热处理, 2024, 49(9): 47-50.
[6]	陈子健, 林业佳, 李传强, 邓仁昡, 董勇, 章争荣. 微合金化调控7075铝合金的微观组织与力学性能[J]. 金属热处理, 2024, 49(9): 58-63.
[7]	孙陶安, 吴正义, 周继顺, 肖丙政, 王海川, 范鼎东, 邓爱军. Mo含量对高碳钢组织和耐磨性的影响[J]. 金属热处理, 2024, 49(9): 64-71.
[8]	路峰, 李琦, 孙雪娇, 邱国兴. 18CrNiMo7-6风电齿轮钢的动态CCT曲线[J]. 金属热处理, 2024, 49(9): 86-90.
[9]	任广笑, 王超, 曹喜娟, 王凯, 王红霞, 程伟丽, 牛晓峰. 时效处理对Mg-Y-Gd-Zn-Zr合金中LPSO相演变及性能的影响[J]. 金属热处理, 2024, 49(9): 96-102.
[10]	任鹏帅, 秦凤, 周骞, 赵雷杰, 崔护, 彭子奥, 武常生. 等温淬火对含铝无碳化物贝氏体钢组织和性能的影响[J]. 金属热处理, 2024, 49(9): 103-109.
[11]	张宇, 李圣阳, 魏晓蓼, 柴志松, 李泳. 铬合金化Q&P钢的热处理工艺优化与碳配分行为[J]. 金属热处理, 2024, 49(9): 110-116.
[12]	张青科, 诸汇涛, 陈根保, 陈立田, 夏亚金, 胡方勤, 宋振纶. 形变热处理对新型无Ti马氏体时效钢焊缝组织与力学性能的影响[J]. 金属热处理, 2024, 49(9): 117-124.
[13]	魏文逸. 热处理对激光沉积制造Ti-5321近β钛合金组织和性能的影响[J]. 金属热处理, 2024, 49(9): 132-138.
[14]	刘煜, 高宇昊, 刘晓勇, 罗先甫, 王佳, 孙绪鲁, 吴泽鹏. 回火处理对05Cr17Ni4Cu4Nb钢性能及晶间腐蚀敏感性的影响[J]. 金属热处理, 2024, 49(9): 144-151.
[15]	夏琳燕, 史湘琴, 刘逸卿, 周模豪, 邓蔚. 时效对铸造Al-Si-Cu-Mg合金力学性能和耐蚀性能的影响[J]. 金属热处理, 2024, 49(9): 152-157.