精密成形齿轮用20MnCr5H钢的球化退火处理

doi:10.13251/j.issn.0254-6051.2024.12.011

金属热处理 ›› 2024, Vol. 49 ›› Issue (12): 67-71.DOI: 10.13251/j.issn.0254-6051.2024.12.011

精密成形齿轮用20MnCr5H钢的球化退火处理

袁静¹, 左彪², 孙万利^3,4, 戴柯明¹, 许宝玉¹, 张朝磊^3,4

1.中天钢铁集团有限公司技术中心, 江苏常州 213011;
2.江苏飞船股份有限公司, 江苏泰州 225300;
3.北京科技大学碳中和研究院, 北京 100083;
4.辽宁材料实验室, 辽宁沈阳 110179

收稿日期:2024-06-17 修回日期:2024-10-28 出版日期:2024-12-25 发布日期:2025-02-05
通讯作者: 张朝磊,副教授,博士,E-mail:zhangchaolei@ustb.edu.cn
作者简介:袁静(1988—),女,工程师,硕士,主要研究方向为钢铁冶金工艺研发,E-mail:yuanjing@zt.net.cn。

Spheroidizing annealing of 20MnCr5H steel for precision formed gears

Yuan Jing¹, Zuo Biao², Sun Wanli^3,4, Dai Keming¹, Xu Baoyu¹, Zhang Chaolei^3,4

1. Technology Center, Zenith Steel Group Co., Ltd., Changzhou Jiangsu 213011, China;
2. Jiangsu Airship Co., Ltd., Taizhou Jiangsu 225300, China;
3. Institute for Carbon Neutrality, University of Science and Technology Beijing, Beijing 100083, China;
4. Liaoning Academy of Materials, Shenyang Liaoning 110179, China

Received:2024-06-17 Revised:2024-10-28 Online:2024-12-25 Published:2025-02-05

摘要/Abstract

摘要： 对精密成形齿轮用20MnCr5H钢进行亚温球化退火(710 ℃×8.5 h)和双相区球化退火(750 ℃×1.5 h+680 ℃×7 h、750 ℃×4 h+710 ℃×4 h、770 ℃×4 h+720 ℃×4 h)处理,探究了不同工艺下的球化处理效果。结果表明,双相区球化退火工艺下,较高的奥氏体区温度会导致片状珠光体难以短时间发生球化转变,而较短的奥氏体区保温时间有助于球化效率提升,750 ℃×1.5 h+680 ℃×7 h取得了较好的球化效果。相较于双相区球化退火,710 ℃×8.5 h亚温球化退火工艺下,20MnCr5H钢球化效果最好,球化率达到98%,这是由于经该工艺处理后,组织中较多的位错和小角度晶界可以促使片状渗碳体更迅速地实现溶断和球化,该工艺是精密成形齿轮的合理球化退火工艺制度。

关键词: 20MnCr5H钢, 亚温球化退火, 双相区球化退火, 球化率

Abstract: The 20MnCr5H steel for precision formed gears was subjected to subcritical spheroidizing annealing (710 ℃×8.5 h) and spheroidizing annealing in dual-phase region (750 ℃×1.5 h+680 ℃×7 h, 750 ℃×4 h+710 ℃×4 h, 770 ℃×4 h+720 ℃×4 h), and the spheroidizing effects under different processes were investigated. The results show that under the spheroidizing annealing in dual-phase region, higher austenite zone temperature will make it difficult for lamellar pearlite to spheroidize in a short time, while shorter austenite zone holding time will help to improve the spheroidization efficiency. Good spheroidization effect is achieved under 750 ℃×1.5 h + 680 ℃×7 h process. Compared with the spheroidizing annealing in dual-phase region, the spheroidization effect of the 20MnCr5H steel is the best under 710 ℃×8.5 h subcritical spheroidizing annealing, and the spheroidization rate reaches 98%. This is due to the fact that after the process treatment, more dislocations and small-angle grain boundaries in the microstructure can promote the dissolution and spheroidization of flaky cementite more quickly. It is a reasonable spheroidizing annealing process for precision forming gears.

Key words: 20MnCr5H steel, subcritical spheroidizing annealing, spheroidizing annealing in dual-phase region, spheroidizing rate

中图分类号:

TG142.1

袁静, 左彪, 孙万利, 戴柯明, 许宝玉, 张朝磊. 精密成形齿轮用20MnCr5H钢的球化退火处理[J]. 金属热处理, 2024, 49(12): 67-71.

Yuan Jing, Zuo Biao, Sun Wanli, Dai Keming, Xu Baoyu, Zhang Chaolei. Spheroidizing annealing of 20MnCr5H steel for precision formed gears[J]. Heat Treatment of Metals, 2024, 49(12): 67-71.

参考文献

[1]惠卫军, 于同仁, 苏世怀, 等. 中碳钢球化退火行为和力学性能的研究[J]. 钢铁, 2005, 40(9): 63-67.
Hui Weijun, Yu Tongren, Su Shihuai, et al. Behavior in spheroidizing annealing and mechanical properties of medium carbon steel[J]. Iron and Steel, 2005, 40(9) : 63-67.
[2]章军, 赵四新. 冷锻齿轮用16MnCrS5钢的球化退火工艺[J]. 金属热处理, 2022, 47(4): 185-188.
Zhang Jun, Zhao Sixin. Spheroidizing annealing process of 16MnCrS5 steel for cold forging gear[J]. Heat Treatment of Metals, 2022, 47(4): 185-188.
[3]王海华, 孙逢源, 林再勇, 等. 球化退火对冷精锻齿轮钢20Cr渗碳晶粒度的影响[J]. 特钢技术, 2022, 28(4): 37-40.
Wang Haihua, Sun Fengyuan, Lin Zaiyong, et al. Effect of spheroidizing annealing on the carburizing grain size of 20Cr cold precision forged gear steel[J]. Special Steel Technology, 2022, 28(4): 37-40.
[4]邱木生, 祭程, 朱苗勇, 等. 冷却速率和奥氏体化温度对40Cr钢球化退火的影响[J]. 工程科学学报, 2015, 37(9): 143-1148.
Qiu Musheng, Ji Cheng, Zhu Miaoyong, et al. Effect of cooling rate and austenitizing temperature on the spheroidizing annealing of 40Cr steel[J]. Chinese Journal of Engineering, 2015, 37(9): 143-1148.
[5]郑晓伟, 林再勇, 张剑锋, 等. 球化退火工艺对渗碳用16MnCr5钢奥氏体晶粒度的影响[J]. 金属热处理, 2023, 48(5): 283-286.
Zheng Xiaowei, Lin Zaiyong, Zhang Jianfeng, et al. Effect of spheroidization annealing process on austenite grain size of 16MnCr5 steel for carburizing[J]. Heat Treatment of Metals, 2023, 48(5): 283-286.
[6]柳萍, 李博鹏, 郑文超, 等. 20CrNiMo钢球化退火工艺研究[J]. 特殊钢, 2022, 43(3): 69-73.
Liu Ping, Li Bopeng, Zheng Wenchao, et al. Study on spheroidizing annealing process of 20CrNiMo steel[J]. Special Steel, 2022, 43(3): 69-73.
[7]邱木生, 邝霜, 滕华湘, 等. 球化退火对SCM435钢组织和力学性能的影响[J]. 热加工工艺, 2019, 48(2): 234-239.
Qiu Musheng, Kuang Shuang, Teng Huaxiang, et al. Effect of spheroidizing annealing on microstructure and mechanical properties of SCM435 steel[J]. Hot Working Technology, 2019, 48(2): 234-239.
[8]程维玮, 孙乐正, 熊兵, 等. 20MnCrS5齿轮钢棒材球化退火工艺的研发[J]. 现代冶金, 2018, 46(4): 45-48.
Cheng Weiwei, Sun Lezheng, Xiong Bing, et al. Development of spheroidal annealing process for 20MnCrS5 gear steel bars[J]. Modern Metallurgy, 2018, 46(4): 45-48.
[9]韩旭, 王洪涛, 韩子玉, 等. 不同球化退火工艺对T12A组织与力学性能影响的研究[J]. 热加工工艺, 2023, 52(4): 116-119, 124.
Han Xu, Wang Hongtao, Han Ziyu, et al. Study on influence of different spheroidization annealing processes on microstructure and mechanical properties of T12A[J]. Hot Working Technology, 2023, 52(4): 116-119, 124.
[10]Su Shengrui, Song Renbo, Chi Chen, et al. The novel process of spheroidizing-critical annealing used to optimize the properties of carburized steel and its effect on hardening mechanism of quenching and tempering[J]. Materials Science and Engineering A, 2019, 765: 138722.
[11]郑晓伟, 王海华, 张剑锋, 等. 拉丝断面压缩率对10B30钢球化退火组织及力学性能的影响[J]. 特殊钢, 2023, 44(1): 93-96.
Zheng Xiaowei, Wang Haihua, Zhang Jianfeng, et al. Effects of wire drawing reduction of cross-sectional area on spheroidizing annealing structure and mechanical properties of 10B30 steel[J]. Special Steel, 2023, 44(1): 93-96.

精密成形齿轮用20MnCr5H钢的球化退火处理

Spheroidizing annealing of 20MnCr5H steel for precision formed gears

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 3

编辑推荐

Metrics

本文评价

[1]	陶涛, 陈颖, 熊兵, 赵海洋, 张世平. 风电螺栓用4140圆钢的球化退火工艺[J]. 金属热处理, 2024, 49(12): 85-89.
[2]	刘坚锋, 喻建林, 葛启录, 仇圣桃, 唐小勇. 原始组织和退火工艺对高碳精冲钢SK85球化效果的影响[J]. 金属热处理, 2021, 46(6): 36-40.
[3]	史啸峰, 柳萍, 李波, 郑文超, 李博鹏, 裴丹丹, 鲁强. 中碳碳素结构钢S55C的球化退火工艺[J]. 金属热处理, 2021, 46(5): 193-195.