大尺寸NiCrMoV钢锻件的预备热处理工艺

doi:10.13251/j.issn.0254-6051.2025.02.037

金属热处理 ›› 2025, Vol. 50 ›› Issue (2): 235-240.DOI: 10.13251/j.issn.0254-6051.2025.02.037

大尺寸NiCrMoV钢锻件的预备热处理工艺

李光¹, 秦红付¹, 李洁^1,2, 苏文博¹, 李梁瑜¹, 金明¹

1.洛阳中重铸锻有限责任公司, 河南洛阳 471039;
2.智能矿山重型装备全国重点实验室, 河南洛阳 471039

收稿日期:2024-08-13 修回日期:2024-12-13 发布日期:2025-04-10
通讯作者: 秦红付,工程师,E-mail:13523606455@163.com
作者简介:李光(1986—),男,工程师,主要研究方向为大型铸锻件工艺技术,E-mail:CITICliguang@163.com。
基金资助:
河南省重大科技专项(221100230200)

Pre-heat treatment process for large size NiCrMoV steel forgings

Li Guang¹, Qin Hongfu¹, Li Jie^1,2, Su Wenbo¹, Li Liangyu¹, Jin Ming¹

1. Luoyang CITIC HIC Casting & Forging Co., Ltd., Luoyang Henan 471039, China;
2. State Key Laboratory of Intelligent Mining Heavy Equipment, Luoyang Henan 471039, China

Received:2024-08-13 Revised:2024-12-13 Published:2025-04-10

摘要/Abstract

摘要： 针对高淬透性NiCrMoV钢锻件锻后晶粒粗大和组织遗传性问题,采用小试样工艺试验的方法,分析了正火前预处理、多次高温正火处理、两相区高温侧正火和退火等热处理工艺方案对切断组织遗传和晶粒细化效果。依据转子芯轴锻件尺寸形状特点,制定了最优的预备热处理工艺方案,提出了奥氏体化加热温度、时间和冷却过程控制措施。结果表明,经最佳预备热处理后,生产的大尺寸锻件本体取样检测实际晶粒度6.5级,锻件超声波探伤满足ø2 mm起始灵敏度要求。

关键词: NiCrMoV钢, 转子芯轴锻件, 晶粒粗大, 组织遗传性, 预备热处理

Abstract: In response to the problem of coarse grain and structural inheritance of high hardenability NiCrMoV steel forgings after forging, a process experiment using small-sized specimens was used to analyze the effect of heat treatment schemes such as pre-treatment before normalizing, multiple high-temperature normalizing treatments, two-phase region high-temperature side normalizing and annealing for cutting off the structural inheritance and for grain refinement. According to the size and shape characteristics of the rotor core shaft forgings, the optimal pre-heat treatment process scheme was developed, and control measures for austenitizing heating temperature and time and cooling process were proposed. The results show that after the optimal pre-heat treatment, the actual grain size of the actual produced large size forging body is sampled and tested as grade 6.5, and the ultrasonic testing of the forging meets the ø2 mm initial sensitivity requirement.

Key words: NiCrMoV steel, rotor core shaft forging, coarse grain, structural inheritance, pre-heat treatment

中图分类号:

TG142.1

李光, 秦红付, 李洁, 苏文博, 李梁瑜, 金明. 大尺寸NiCrMoV钢锻件的预备热处理工艺[J]. 金属热处理, 2025, 50(2): 235-240.

Li Guang, Qin Hongfu, Li Jie, Su Wenbo, Li Liangyu, Jin Ming. Pre-heat treatment process for large size NiCrMoV steel forgings[J]. Heat Treatment of Metals, 2025, 50(2): 235-240.

参考文献

[1] 杨正汉. 电站用大型锻件锻后热处理[J]. 国外金属热处理, 1997, 10(1): 18-20.
[2] 姜超. 大型锻件热处理过程晶粒度变化的研究[D]. 北京: 北京机电研究所, 2004.
Jiang Chao. Study on grain size transformation during heat treatment of large forgings[D]. Beijing: Beijing Research Institute of Mechanical and Electrical Technology, 2004.
[3] 陈睿恺. 30Cr2Ni4MoV钢低压转子热处理工艺的研究[D]. 上海: 上海交通大学, 2012.
Chen Ruikai. Study on heat treatment for low pressure rotors of 30Cr2Ni4MoV steel[D]. Shanghai: Shanghai Jiao Tong University, 2012.
[4] 薛康, 张秀芝, 高潇, 等. 正火时间对不同变形后30Cr2Ni4MoV钢晶粒度的影响[J]. 热加工工艺, 2016, 45(8): 197-203.
Xue Kang, Zhang Xiuzhi, Gao Xiao, et al. Influence of normalizing time on grain size of 30Cr2Ni4MoV steel after different deformation[J]. Hot Working Technology, 2016, 45(8): 197-203.
[5] 李安民. 30CrNi2MoV钢的组织遗传与晶粒细化[J]. 金属热处理, 2013, 32(4): 82-84.
Li Anmin. Investigation on structure inheritance and fine-graining of 30CrNi2MoV steel[J]. Heat Treatment of Metals, 2013, 32(4): 82-84.
[6] 牟军, 张丰, 康大韬. 大锻件组织遗传的细化工艺的比较研究[J]. 材料导报, 1995, 10(6): 25-30.
Mou Jun, Zhang Feng, Kang Datao. Comparative studies on techniques to remove grain heredity in large forgings[J]. Materials Reports, 1995, 10(6): 25-30.
[7] 谭立军, 王峻乔, 王庆群, 等. 25Cr2Ni4MoV钢大型锻件的组织与力学性能[J]. 金属热处理, 2014, 39(1): 128-131.
Tan Lijun, Wang Junqiao, Wang Qingqun, et al. Microstructure and mechanical properties of 25Cr2Ni4MoV steel large forgings[J]. Heat Treatment of Metals, 2014, 39(1): 128-131.
[8] 黄倩, 温彤, 刘清, 等. 大型锻件组织与性能的影响因素及其控制技术[J]. 热加工工艺, 2015, 44(13): 6-8.
Huang Qian, Wen Tong, Liu Qing, et al. Affecting factors and control technology of microstructure and properties of large forgings[J]. Hot Working Technology, 2015, 44(13): 6-8.

大尺寸NiCrMoV钢锻件的预备热处理工艺

Pre-heat treatment process for large size NiCrMoV steel forgings

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 5

编辑推荐

Metrics

本文评价

[1]	杨树林, 赵吉庆, 闫磊, 杨钢. эи866合金锻件径向条纹形成原因与消除工艺[J]. 金属热处理, 2023, 48(9): 279-282.
[2]	陈建礼, 楚宝帅, 张晓琨. 4Cr5Mo2V扁钢中AS14类退火组织成因分析[J]. 金属热处理, 2023, 48(5): 66-69.
[3]	鲍玉龙, 于香华, 尹卓君. ZG25CrNiMo钢组织遗传及预先热处理对调质后力学性能的影响[J]. 金属热处理, 2023, 48(12): 140-143.
[4]	李伟, 刘京, 邵洙浩, 郝红军, 唐林, 姜涛. 1Cr12MoV钢锻件力学性能不合格原因分析及工艺改进[J]. 金属热处理, 2023, 48(11): 300-304.
[5]	樊伟, 王科社, 查初亮. 高性能GCr15钢滚珠丝杠的热加工工艺[J]. 金属热处理, 2014, 39(12): 55-58.