缓冷出口温度对连续退火SPCC冷轧薄板屈服强度的影响

doi:10.13251/j.issn.0254-6051.2020.02.025

摘要/Abstract

摘要：

研究了缓冷出口温度对连续退火SPCC冷轧薄板组织和屈服强度的影响。结果表明:连续退火SPCC冷轧薄板的组织由等轴的铁素体晶粒和晶界处的块状渗碳体及晶粒内的颗粒状渗碳体组成。随着缓冷出口温度从680 ℃提高至700 ℃,平均晶粒尺寸从10.1 μm增加至12.5 μm;此外,提高缓冷出口温度还能够抑制晶界处块状渗碳体的形成,促进晶粒内细小渗碳体更加细小弥散的析出。当缓冷出口温度从680 ℃提高至700 ℃时,冷轧薄板的屈服强度约降低了28 MPa。

关键词: 连续退火, 缓冷出口温度, SPCC冷轧薄板, 显微组织, 屈服强度

Abstract:

Effect of continuous annealing slow cooling outlet temprature on microstructures and yield strength of SPCC cold rolled sheet was studied. The results show that the microstructure of the continuous annealed SPCC cold rolled sheet mainly consists of equiaxed ferrite grains, massive cementites on grain boundaries and spheroidite cementites in grains. With the increase of slow cooling outlet temprature from 680 ℃ to 700 ℃, the average grain size increases from 10.1 μm to 12.5 μm. In addition, increasing the slow cooling outlet temprature can promote the precipitation of fine cementites in grains by inhibiting the formation of massive cementites on grain boundaries. When the slow cooling outlet temprature increases from 680 ℃ to 700 ℃, the yield strength of the continuous annealed SPCC cold rolled sheet decreases by about 28 MPa.

Key words: continuous annealing, slow cooling outlet temprature, SPCC cold rolled sheet, microstructure, yield strength

中图分类号:

TG142.1

周博文, 蒋才灵, 樊雷, 周骅, 高源, 李宇楠, 叶姜. 缓冷出口温度对连续退火SPCC冷轧薄板屈服强度的影响[J]. 金属热处理, 2020, 45(2): 129-133.

Zhou Bowen, Jiang Cailing, Fan Lei, Zhou Hua, Gao Yuan, Li Yu'nan, Ye Jiang. Effect of continuous annealing slow cooling outlet temperature on yield strength of SPCC cold rolled sheet[J]. HTM, 2020, 45(2): 129-133.

参考文献

[1]汤茜, 李腾飞, 李婷婷, 等. 连续退火SPCC冷轧薄板性能的影响因素[J]. 金属热处理, 2013, 38(9): 60-64.
Tang Xi, Li Tengfei, Li Tingting, et al. Influence factors on properties of SPCC cold rolled sheet after continuous annealing[J]. Heat Treatment of Metals, 2013, 38(9): 60-64.
[2]刘吉志, 冯锐, 刘玉爱. 再结晶退火对SPCC钢板组织和深冲性能的影响[J]. 山东冶金, 2018, 40(2): 39-41.
Liu Jizhi, Feng Rui, Liu Yuai. Effect of recrystallization annealing process on microstructure and deep drawability of SPCC steel plate[J]. Shandong Metallurgy, 2018, 40(2): 39-41.
[3]张华, 金自力, 齐蒙, 等. 包钢连续退火冷轧SPCC性能优化[J]. 包钢科技, 2018, 44(5): 51-54.
Zhang Hua, Jin Zili, Qi Meng, et al. Performance optimization for cold rolled SPCC with continuous annealing in Baotou steel[J]. Science and Technology of Baotou Steel, 2018, 44(5): 51-54.
[4]程晓杰, 李振, 蔡阿云, 等. 连续退火温度对390 MPa级IF钢组织、织构和力学性能的影响[J]. 特殊钢, 2014, 35(3): 53-55.
Cheng Xiaojie, Li Zhen, Cai Ayun, et al. Effect of continuous annealing temperature on structure, texture and mechanical properties 390 MPa IF steel[J]. Special Steel, 2014, 35(3): 53-55.
[5]陈爱华, 李化龙, 李腾飞. 连续退火温度对IF钢力学性能及织构的影响[J]. 金属热处理, 2016, 41(6): 37-41.
Chen Aihua, Li Hualong, Li Tengfei. Influence of continuous annealing temperature on mechanical properties and texture of IF steel[J]. Heat Treatment of Metals, 2016, 41(6): 37-41.
[6]袁龙兵, 张仲良, 吴文林, 等. 连续退火温度对马钢CSP-冷轧IF钢板塑性应变比r值的影响[J]. 安徽冶金科技职业学院学报, 2008, 18(3): 7-9.
Yuan Longbing, Zhang Zhongliang, Wu Wenlin, et al. Effect of continuous annealing temperature of cold rolling IF steel produced by CSP process on r value[J]. Journal of Anhui Vocational College of Metallurgy and Technology, 2008, 18(3): 7-9.
[7]张少红, 郑志刚, 李秀军. SPCC产品的连退工艺研究[J]. 机械工程与自动化, 2010(2): 116-118.
Zhang Shaohong, Zheng Zhigang, Li Xiujun. Continuous annealing process about SPCC products[J]. Mechanical Engineering and Automation, 2010(2): 116-118.
[8]王淑华, 梅淑文, 杨晓江, 等. 硼对冷轧罩退低碳钢带组织及性能的影响[J]. 河北冶金, 2015(7): 15-18.
Wang Shuhua, Mei Shuwen, Yang Xiaojiang, et al. Influence of boron on structure and property of cold rolling batch annealing low carbon steel strip[J]. Hebei Metallurgy, 2015(7): 15-18.
[9]尹翠兰. 冷轧SPCC带钢冲压性能分析与优化[J]. 山东冶金, 2015, 37(3): 28-31.
Yin Cuilan. Analysis and optimization of stamping properties of SPCC cold rolled strip[J]. Shandong Metallurgy, 2015, 37(3): 28-31.
[10]张志明, 王志华. 连续退火时间对SPCC冷轧钢板性能的影响[J]. 山西焦煤科技, 2012, 36(7): 27-29.
Zhang Zhiming, Wang Zhihua. Continuous annealing time on the mechanical properties of SPCC cold-rolled steel sheet[J]. Shanxi Coking Coal Science and Technology, 2012, 36(7): 27-29.
[11]高荣庆, 吴庚亮, 孙建卫. 压下率和退火温度对SPCC冷轧钢带组织与性能的影响[J]. 金属热处理, 2011, 36(7): 23-27.
Gao Rongqing. Wu Gengliang, Sun Jianwei. Effect of reduction ratio and annealing temperature on microstructure and mechanical properties of SPCC cold rolled steel strip[J]. Heat Treatment of Metals, 2011, 36(7): 23-27.
[12]杜晶晶, 宋仁伯, 杨富强. 退火工艺对薄规格SPCC钢板组织和性能的影响[J]. 武汉科技大学学报, 2012, 36(1): 21-25.
Du Jingjing, Song Renbo, Yang Fuqiang. Effect of annealing process on structure and properties of thin SPCC sheet[J]. Journal of Wuhan University of Science and Technology, 2012, 36(1): 21-25.
[13]谢华. 游离渗碳体形态对S15A深冲钢冲击性能的影响[J]. 理化检验-物理分册, 2012, 48(2): 87-90.
Xie Hua. Effect of free cementite morphology on impact property of S15A deep punching steel[J]. Physical Testing and Chemical Analysos Part A: Physical Testing, 2012, 48(2): 87-90.
[14]廖舒纶, 沈奎, 于学森, 等. 提高低碳钢拉拔性能的工艺研究[J]. 热加工工艺, 2017, 46(5): 190-192.
Liao Shulun, Shen Kui, Yu Xuesen, et al. Technical research on improving drawing performance of low carbon steel[J]. Hot Working Technology, 2017, 46(5): 190-192.
[15]孙中华, 安治国, 熊自柳, 等. SPCC薄板冷轧及连续退火工艺研究[J]. 河北冶金, 2013(2): 1-7.
Sun Zhonghua, An Zhiguo, Xiong Ziliu, et al. Study about technology for cold rolling and continuous annealing of SPCC sheet[J]. Hebei Metallurgy, 2013(2): 1-7.
[16]叶卫平, 勾亚峰. 加热速率和形变量对IF钢再结晶温度的影响[J]. 金属热处理, 2001(3): 19-20.
Ye Weiping, Gou Yafeng. Effect of heat rate and cold rolled rate on recrystallization temperature of IF steel[J]. Heat Treatment of Metals, 2001(3): 19-20.
[17]李萧, 杨平, 林瑞民, 等. 低碳冲压钢板性能缺陷的组织与织构检测分析[C]. 中国体视学与图像分析学术会议, 2008: 274-277.
Li Xiao, Yang Ping, Lin Ruimin, et al. Structural and textural determination and analysis of low carbon deep-drawing steel defects[C]. Chinese academic conference on stereology and image analysis, 2008: 274-277.