铲齿用新型空冷贝氏体钢的热处理工艺

doi:10.13251/j.issn.0254-6051.2020.08.035

金属热处理 ›› 2020, Vol. 45 ›› Issue (8): 179-184.DOI: 10.13251/j.issn.0254-6051.2020.08.035

铲齿用新型空冷贝氏体钢的热处理工艺

郑丽丽^1,2, 安胜利^1,2, 彭军^1,2, 张芳^1,2, 高占勇^1,2, 焦海东^1,2

1.内蒙古科技大学材料与冶金学院, 内蒙古包头 014010;
2.内蒙古自治区先进陶瓷材料与器件重点实验室, 内蒙古包头 014010

收稿日期:2020-02-02 出版日期:2020-08-25 发布日期:2020-09-07
通讯作者: 安胜利,教授,博士,E-mail:san@imust.edu.cn
作者简介:郑丽丽(1988—),女,博士研究生,主要研究方向为微合金化钢的研究与应用,E-mail:1322468323@qq.com
基金资助:
国家自然科学基金(51874186,51664046,51664044);内蒙古应用技术研究与开发计划(201802022)

Heat treatment process of new air-cooling bainitic steel for shovel teeth

Zheng Lili^1,2, An Shengli^1,2, Peng Jun^1,2, Zhang Fang^1,2, Gao Zhanyong^1,2, Jiao Haidong^1,2

1. College of Material and Metallurgy, Inner Mongolia University of Science and Technology, Baotou Inner Mongolia 014010, China;
2. Inner Mongolia Autonomous Region Key Laboratory of Advanced Ceramic Materials and Devices, Baotou Inner Mongolia 014010, China

Received:2020-02-02 Online:2020-08-25 Published:2020-09-07

摘要/Abstract

摘要： 为了解决铲齿使用寿命短的问题,对新型贝氏体组织铲齿用钢及其热处理工艺进行了研究。通过火花直读光谱仪和热膨胀仪检测了贝氏体钢的化学成分和相变点,采用正交试验的方法研究了正火温度、回火温度、回火时间对贝氏体钢韧性的影响,确定了最优的热处理工艺,借助扫描电镜(SEM)、Image-J软件、X射线衍射仪(XRD)及数显显微硬度仪等检测了铲齿用贝氏体钢的组织和组织中相组成比例以及其硬度。研究结果表明贝氏体铲齿用钢在热处理过程中影响冲击性能最主要的因素为正火温度,其次为回火温度、最后为回火时间,得到的最优热处理工艺制度为1080 ℃正火后在250 ℃回火90 min,此热处理条件下贝氏体钢具有良好的韧性(18.45 J)和硬度(46.85 HRC)结合,其组织中马氏体含量为23.985%,残留奥氏体含量为9.850%。

关键词: 铲齿, 贝氏体钢, 热处理, 组织, 性能

Abstract: In order to solve the problem of short service life of shovel teeth, the new bainitic steel and its heat treatment process were studied. The chemical composition and phase transition points of the bainitic steel were tested by spark direct reading spectrometer and thermal dilatometer. Effect of normalizing temperature, tempering temperature and tempering time on the toughness of the bainitic steel was studied by orthogonal test method, and the optimal heat treatment process was determined. Microstructure, phase composition ratio and hardness of bainitic steel for shovel teeth were measured by means of scanning electron microscopy, Image-J software, X-ray diffractometer and digital microhardness tester. The results show that the most important factor affecting the impact toughness of the bainitic steel is the normalizing temperature, then the tempering temperature and the tempering time in order. The optimal heat treatment process is normalizing at 1080 ℃+tempering at 250 ℃ for 90 min, by which the bainitic steel obtains a good combination of toughness (18.45 J) and hardness (46.85 HRC), and the content of martensite and retained austenite in the microstructure is 23.985% and 9.850%, respectively.

Key words: shovel teeth, bainitic steel, heat treatment, microstructure, properties

中图分类号:

TG161

郑丽丽, 安胜利, 彭军, 张芳, 高占勇, 焦海东. 铲齿用新型空冷贝氏体钢的热处理工艺[J]. 金属热处理, 2020, 45(8): 179-184.

Zheng Lili, An Shengli, Peng Jun, Zhang Fang, Gao Zhanyong, Jiao Haidong. Heat treatment process of new air-cooling bainitic steel for shovel teeth[J]. Heat Treatment of Metals, 2020, 45(8): 179-184.

参考文献

[1]唐春霞, 曹文全. 耐磨钢的国内生产现状及发展前景[J]. 宽厚板, 2018, 24(3): 37-41.
Tang Chunxia, Cao Wenquan. Current production situation and development prospect of wear resistant steel at home[J]. Wide and Heavy Plate, 2018, 24(3): 37-41.
[2]杨芳, 丁志敏. 耐磨高锰钢的发展现状[J]. 机车车辆工艺, 2006(6): 6-9.
Yang Fang, Ding Zhiming. Development status of wear-resistant high manganese steel[J]. Locomotive and Rolling Stock Technology, 2006(6): 6-9.
[3]于祥和, 余信武. 进口挖掘机斗齿抗磨材料及制造工艺[J]. 机械工人, 2000(11): 35-36.
[4]Eugeniusz Rusin＇ski, Lesław Cegiel, Andrzej Michalczyk, et al. Investigation and modernization of buckets of surface mining machines[J]. Engineering Structures, 2015, 90: 29-37.
[5]畅西原, 于浩令. 电铲铲齿的失效及材质选择[J]. 铸造技术, 2010, 31(8): 1098-1100.
Chang Xiyuan, Yu Haoling. Failure and material selection of shovel teeth[J]. Foundry Technology, 2010, 31(8): 1098-1100.
[6]张伟旗. 大型矿山挖掘机斗齿失效机制及控制研究[J]. 有色设备, 2017(3): 5-10, 31.
Zhang Weiqi. Study on the failure mechanism and control of bucket teeth in large-scale mine excavator[J]. Non-Ferrous Metallurgical Equipment, 2017(3): 5-10, 31.
[7]郑丽丽, 彭军, 安胜利, 等. 国内外铲齿用钢的研究现状与发展前景[J]. 金属热处理, 2020, 45(5): 229-235.
Zheng Lili, Peng Jun, An Shengli, et al. Research status and development prospect of steels for shovel teeth at home and abroad[J]. Heat Treatment of Metals, 2020, 45(5): 229-235.
[8]程巨强. 采煤机截齿的选材与制造工艺[J]. 凿岩机械气动工具, 2013(1): 25-30.
Cheng Juqiang. Material selection and manufacturing process of shearer picks[J]. Rock Drilling Machinery and Pneumatic Tools, 2013(1): 25-30.
[9]姜忠良, 陈秀云, 陈晓东, 等. 截齿用新型高硅低碳空冷贝氏体钢的组织与性能[J]. 清华大学学报(自然科学版), 2001(10): 23-26.
Jiang Zhongliang, Chen Xiuyun, Chen Xiaodong, et al. Microstructure and properties of low-carbon air-cooling bainite steels with high Si used for pickers[J]. Journal of Tsinghua University (Science and Technology), 2001(10): 23-26.
[10]Mashloosh K M, Eyre T S. Abrasive wear and its application to digger teeth[J]. Tribology International, 1985, 18(5): 259-266.
[11]Srdan M Bošnjaka, Miodrag A Arsićb, Nebojša B Gnjatovića, et al. Failure of the bucket wheel excavator buckets[J]. Engineering Failure Analysis, 2018, 84: 247-261.
[12]Shivali Singla, Amardeep S Kang, Jasmaninder S Grewal, et al. Wear behavior of weld overlays on excavator bucket teeth[J]. Procedia Materials Science, 2014, 5: 256-266.
[13]Fernández J E, Vijande R, Tucho R, et al. Materials selection to excavator teeth in mining industry[J]. Wear, 2001, 250: 11-18.
[14]樊朋煜, 刘蓉, 高古辉, 等. 钒及热处理工艺对贝氏体钢中奥氏体碳富集的影响[J]. 金属热处理, 2020, 45(1): 11-15.
Fan Pengyu, Liu Rong, Gao Guhui, et al. Effect of V and heat treatment on carbon enrichment in austenite of bainitic steel[J]. Heat Treatment of Metals, 2020, 45(1): 11-15.
[15]方鸿生, 薄祥正, 郑燕康, 等. 贝氏体组织与贝氏体钢[J]. 金属热处理, 1988(11): 2-7.
Fang Hongshen, Bo Xiangzheng, Zheng Yankang, et al. Bainitic microstructure and Mn-B bainitic steels[J]. Heat Treatment of Metals, 1988(11): 2-7.
[16]王楠, 胡志华, 王正云, 等. 新型重载辙叉贝氏体钢的组织与性能[J]. 金属热处理, 2020, 45(4): 90-93.
Wang Nan, Hu Zhihua, Wang Zhengyun, et al. Microstructure and properties of bainitic steel for new heavy-duty railway frog[J]. Heat Treatment of Metals, 2020, 45(4): 90-93.
[17]徐祖耀, 刘世揩. 贝氏体相变与贝氏体[M]. 北京: 科学出版社, 1991.
Xu Zuyao, Liu Shikai. Bainite Transformation and Bainite[M]. Beijing: Science Press, 1991.
[18]徐祖耀. 贝氏体相变简介[J]. 热处理, 2006(2): 1-20.
Xu Zuyao. A brief introduction to bainitic transformation[J]. Heat Treatment, 2006(2): 1-20.
[19]席光兰, 马勤. 贝氏体钢的研究现状和发展展望[J]. 材料导报, 2006(4): 78-81.
Xi Guanglan, Ma Qin. The research situation and development prospect of bainitic steels[J]. Materials Review, 2006(4): 78-81.
[20]Lee K M, Polycarpou A. Wear of conventional pearlitic and improved bainitic rail steels[J]. Wear, 2005, 259: 391-399.
[21]Aglan H A, Liu Z Y, Hassan M F, et al. Mechanical and fracture behavior of bainitic rail steel[J]. Journal of Materials Processing Technology, 2004, 151: 268-274.
[22]Manuel Gomez, Lucía Rancel, Esther Escudero, et al. Phase transformation under continuous cooling conditions in medium carbon microalloyed steels[J]. Journal of Materials Processing Technology, 2014, 30(5): 511-516.
[23]方鸿生, 郑燕康, 陈秀云, 等. 发展新型贝氏体钢[J]. 兵器材料科学与工程, 1988, 11: 1-13.
Fang Hongsheng, Zheng Yankang, Chen Xiuyun, et al. Development of new bainitic steel[J]. Ordnance Material Science and Engineering, 1988, 11: 1-13.
[24]Sourmail T, Smanio V, Ziegler C, et al. Novel nanostructured bainitic steel grades to answer the need for high-performance steel components (Nanobain)[J]. Materials Science and Engineering A, 2013, 582: 257-261.
[25]Garcia Mateo C, Caballero F G. Handbook of Mechanical Nanostructuring[M]. Germany: Wiley, 2015: 35-65.

铲齿用新型空冷贝氏体钢的热处理工艺

Heat treatment process of new air-cooling bainitic steel for shovel teeth

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	王玉岱, 刘洋, 朱言言, 田象军, 程序, 冉先喆, 钱婷婷. 热处理对复合制造AerMet100超高强度钢组织均匀性与拉伸性能的影响[J]. 金属热处理, 2022, 47(4): 1-9.
[2]	张子延, 陈君, 陈晓亚, 李全安, 刘建鑫. 固溶时效处理对Mg-4Sm-3Gd-0.5Zr合金显微组织和耐蚀性能的影响[J]. 金属热处理, 2022, 47(4): 10-16.
[3]	梁恩溥, 徐乐, 杨勇, 王毛球. 添加Al、Cu对40CrNi3MoV钢组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 17-23.
[4]	祁晓亮, 李岩, 定巍, 赵增武. 含Al中锰TRIP钢原始组织对临界退火后组织与力学性能的影响[J]. 金属热处理, 2022, 47(4): 24-29.
[5]	陈保安, 张静媛, 祝志祥, 韩钰, 潘学东, 张磊, 陈素红. 化学成分对高强Al-Mg-Si合金组织和性能的影响[J]. 金属热处理, 2022, 47(4): 30-38.
[6]	陈东俊, 李广阳, 刘刚. 时效处理对AlSi9Cu3压铸铝合金组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 53-56.
[7]	陈连生, 张露友, 田亚强, 杨子旋, 李红斌, 潘红波, 魏英立. 低碳高强舰船用钢的CCT曲线及其组织性能[J]. 金属热处理, 2022, 47(4): 63-68.
[8]	贾昌远, 霍元明, 何涛, 霍存龙, 刘克然. 40CrNiMo钢高温拉伸变形行为和组织演变规律[J]. 金属热处理, 2022, 47(4): 69-74.
[9]	王云龙, 余伟, 张昳, 史佳新, 李明辉. 奥氏体化温度对贝氏体钢等温转变及力学性能的影响[J]. 金属热处理, 2022, 47(4): 80-85.
[10]	陈思君, 陈送义, 陈庚, 袁丁玲, 陈康华. Mg含量对2A14铝合金组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 86-92.
[11]	刘丽艳, 毕文珍, 韦习成. Mn元素对热冲压钢镀锌层组织演变的影响[J]. 金属热处理, 2022, 47(4): 93-99.
[12]	骆再斌, 范子泽, 彭振. 轻质高熵合金的研究进展[J]. 金属热处理, 2022, 47(4): 100-107.
[13]	白青青, 张志宏, 郑淮北, 王英虎. 2507超级双相不锈钢中σ相的析出行为[J]. 金属热处理, 2022, 47(4): 108-115.
[14]	陈刚, 罗小兵, 柴锋, 杨才福, 张正延, 杨丽. 轧制加热温度对高强度低合金钢组织及冲击性能的影响[J]. 金属热处理, 2022, 47(4): 116-121.
[15]	付锡彬, 陈子豪, 张可, 赵时雨, 孙新军, 朱正海, 梁小凯, 雍岐龙. 淬火温度对高Ti低合金耐磨钢组织及力学性能的影响[J]. 金属热处理, 2022, 47(4): 122-127.