选区激光熔化316L不锈钢的各向组织与性能

doi:10.13251/j.issn.0254-6051.2020.09.030

金属热处理 ›› 2020, Vol. 45 ›› Issue (9): 161-166.DOI: 10.13251/j.issn.0254-6051.2020.09.030

选区激光熔化316L不锈钢的各向组织与性能

张仁奇¹, 樊磊¹, 周宝刚^1,2, 梁宇²

1.贵州电网有限责任公司电力科学研究院,贵州贵阳 550002;
2.贵州大学材料与冶金学院,贵州贵阳 550025

收稿日期:2020-03-28 出版日期:2020-09-25 发布日期:2020-12-29
通讯作者: 梁宇,教授,E-mail:xq.liangyu@126.com
作者简介:张仁奇(1968—),男,高级工程师,主要研究方向为电网设备结构失效分析,E-mail:zhrq1968@163.com
基金资助:
贵州省电力试验研究院项目(066601[2018]030103JS112);国家自然科学基金(51761003)

Microstructure and properties of selective laser melted 316Lstainless steel in different directions

Zhang Renqi¹, Fan Lei¹, Zhou Baogang^1,2, Liang Yu²

1. Electric Power Research Institute of Guizhou Power Grid Co.,Ltd.,Guiyang Guizhou 550002,China;
2. College of Materials and Metallurgy,Guizhou University,Guiyang Guizhou 550025,China

Received:2020-03-28 Online:2020-09-25 Published:2020-12-29

摘要/Abstract

摘要： 对采用选区激光熔化(SLM)制备的316L不锈钢增材制造试样进行了横向、纵向力学性能与微观组织分析。结果表明,增材制造SLM试件亚结构组织由尺寸为0.4 μm左右的胞状组织所构成,组织之间无明显的成分偏析,纵向与横向拉伸强度分别达到808和713 MPa,在经过1050 ℃热处理后,原组织中部分胞状组织消失,纵向及横向强度分别下降到673 MPa及579 MPa,增材制造试样相对传统热轧试样(550 MPa)具有明显的强度优势。SLM试样组织中存在未熔合缺陷,缺陷几何形状的方向性对其在拉应力作用下连接成裂纹有显著影响。热处理后缺陷长度方向与拉伸应力平行的纵向试样伸长率达到47.5%,横向试样伸长率为20%,伸长率指标均显著低于热轧316L钢试样,未熔合缺陷是导致3D打印试件塑性指标降低的主要因素之一。

关键词: 316L不锈钢, 选区激光熔化, 微观组织, 力学性能

Abstract: Microstructure and properties in transversal and longitudinal directions of 316L stainless steel additive manufacturing specimens produced by selective laser melting(SLM) were analyzed.The results show that the substructure of the SLM additive manufacturing specimens is composed of cellular microstructure with the size of 0.4 μm,and with no obvious composition segregation.Their transversal and longitudinal tensile strengths are 808 MPa and 713 MPa,respectively.After heat treatment at 1050 ℃,some of the cellular microstructures disappear,and the transversal and longitudinal strengths are reduced to 673 MPa and 579 MPa,respectively,which still have obvious strength advantages compared with the conventional hot rolled 316L steel(550 MPa).There are unfused defects in the SLM specimens,and the directivity and geometry of the defects have significant effect on the ability of the defects joining into a crack under the action of tensile stress.The elongation of the longitudinal specimen with defect length direction parallel to the tensile direction is 47.5%,and that of the transversal specimen is 20% after heat treatment.The elongation of the SLM specimen is significantly lower than that of the hot rolled 316L steel specimen.The unfused defect is one of the main factors leading to the decrease of plastic properties of the 316L stainless steel specimens processed by SLM.

Key words: 316L stainless steel, selective laser melting, microstructure, mechanical properties

中图分类号:

TG401

张仁奇, 樊磊, 周宝刚, 梁宇. 选区激光熔化316L不锈钢的各向组织与性能[J]. 金属热处理, 2020, 45(9): 161-166.

Zhang Renqi, Fan Lei, Zhou Baogang, Liang Yu. Microstructure and properties of selective laser melted 316Lstainless steel in different directions[J]. Heat Treatment of Metals, 2020, 45(9): 161-166.

参考文献

[1] Zhao J L,Zhi Z F,Sun D,et al.Antibacterial durability and biocompatibility of antibacterial-passivated 316L stainless steel in simulated physiological environment[J].Materials Science and Engineering C,2019,100:396-410.
[2] Yang Y,Zhu Y,Khonsari M M,et al.Wear anisotropy of selective laser melted 316L stainless steel[J].Wear,2019,428-429:376-386.
[3] Saeidi K,Neikter M,Olsen J,et al.316L stainless steel designed to withstand intermediate temperature[J].Materials and Design,2017,135:1-8.
[4] Frazier W E.Metal additive manufacturing:A review[J].Journal of Materials Engineering and Performance,2014,23(6):1917-1928.
[5] Zhang Y,Wu L,Guo X,et al.Additive manufacturing of metallic materials:A review[J].Journal of Materials Engineering and Performance,2018,27(1):1-13.
[6] Kong D,Ni X,Dong C,et al.Heat treatment effect on the microstructure and corrosion behavior of 316L stainless steel fabricated by selective laser melting for proton exchange membrane fuel cells[J].Electrochimica Acta,2018,276:293-303.
[7] Liu G L,Yang S W,Han W T,et al.Microstructural evolution of dissimilar welded joints between reduced-activation ferritic-martensitic steel and 316L stainless steel during the post weld heat treatment[J].Materials Science and Engineering A,2018,722:182-196.
[8] Tomasz K,Konrad G,Wojciech S,et al.Correlation between process parameters,microstructure and properties of 316 L stainless steel processed by selective laser melting[J].Materials Science and Engineering A,2018,718:64-73.
[9] Gray G T,Livescu V,Rigg P A,et al.Structure/property(constitutive and spallation response)of additively manufactured 316L stainless steel[J].Acta Materialia,2017,138:140-149.
[10] 尹燕,刘鹏宇,路超,等.选区激光熔化成形316L不锈钢微观组织及拉伸性能分析[J].焊接学报,2018,39(8):77-81.
Yin Yan,Liu Pengyu,Lu Chao,et al.Microstructure and tensile properties of selective laser melting forming 316L stainless steel[J].Transaction of the China Welding Institution,2018,39(8):77-81.
[11] 边培莹.热处理工艺对 316L 不锈钢粉末激光选区熔化成形的残余应力及组织的影响[J].材料热处理学报,2019,40(4):90-97.
Bian Peiying.Effect of heat treatment on residual stress and microstructure of 316L stainless steel powder formed by selective laser melting[J].Transactions of Materials and Heat Treatment,2019,40(4):90-97.
[12] Casati R,Lemke J,Vedani M,et al.Microstructure and fracture behavior of 316L austenitic stainless steel produced by selective laser melting[J].Journal of Materials Science and Technology,2016,32:738-744.
[13] Salman O O,Gammer C,Chaubey A K,et al.Effect of heat treatment on microstructure and mechanical properties of 316L steel synthesized by selective laser melting[J].Materials Science and Engineering A,2019,748:205-212.
[14] Liverani E,Toschi S,Ceschini L,et al.Effect of selective laser melting(SLM)process parameters on microstructure and mechanical properties of 316L austenitic stainless steel[J].Journal of Materials Processing Technology,2017,249:255-263.
[15] Deev A A,Kuznetcov P A,Petrov S N,et al.Anisotropy of mechanical properties and its correlation with the structure of the stainless steel 316L produced by the SLM method[J].Physics Procedia,2016,83:789-796.
[16] Bahl S,Mishra S,Yazar K U,et al.Non-equilibrium microstructure,crystallographic texture and morphological texture synergistically result in unusual mechanical properties of 3D printed 316L stainless steel[J].Additive Manufacturing,2019,28:65-77.

选区激光熔化316L不锈钢的各向组织与性能

Microstructure and properties of selective laser melted 316Lstainless steel in different directions

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	梁恩溥, 徐乐, 杨勇, 王毛球. 添加Al、Cu对40CrNi3MoV钢组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 17-23.
[2]	祁晓亮, 李岩, 定巍, 赵增武. 含Al中锰TRIP钢原始组织对临界退火后组织与力学性能的影响[J]. 金属热处理, 2022, 47(4): 24-29.
[3]	陈保安, 张静媛, 祝志祥, 韩钰, 潘学东, 张磊, 陈素红. 化学成分对高强Al-Mg-Si合金组织和性能的影响[J]. 金属热处理, 2022, 47(4): 30-38.
[4]	陈东俊, 李广阳, 刘刚. 时效处理对AlSi9Cu3压铸铝合金组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 53-56.
[5]	陈连生, 张露友, 田亚强, 杨子旋, 李红斌, 潘红波, 魏英立. 低碳高强舰船用钢的CCT曲线及其组织性能[J]. 金属热处理, 2022, 47(4): 63-68.
[6]	王云龙, 余伟, 张昳, 史佳新, 李明辉. 奥氏体化温度对贝氏体钢等温转变及力学性能的影响[J]. 金属热处理, 2022, 47(4): 80-85.
[7]	骆再斌, 范子泽, 彭振. 轻质高熵合金的研究进展[J]. 金属热处理, 2022, 47(4): 100-107.
[8]	李立, 曾艳, 吴晓春. 4Cr5Mo2VCo钢的热处理工艺优化[J]. 金属热处理, 2022, 47(4): 133-140.
[9]	吕杰晟, 宋志刚, 何建国, 丰涵, 郑文杰, 朱玉亮. S32205双相不锈钢冷轧退火组织转变及强塑化机理分析[J]. 金属热处理, 2022, 47(4): 141-145.
[10]	王琪, 吴光亮. 回火温度对1100 MPa级高强钢组织与性能的影响[J]. 金属热处理, 2022, 47(4): 146-150.
[11]	张骥俊, 邢彦锋, 曹菊勇. 超声振动对CMT电弧增材制造铝合金组织与性能的影响[J]. 金属热处理, 2022, 47(4): 159-164.
[12]	李梦, 武美萍, 陆佩佩, 赵子硕, 缪小进. 选区激光熔化MnSi₂增强316L不锈钢复合材料的表面质量及耐蚀性能[J]. 金属热处理, 2022, 47(4): 165-170.
[13]	刘文彬, 乔龙阳, 潘新宇, 程格, 李爱娜, 裴新军. 淬火温度对刀剪用M390粉末冶金不锈钢组织和性能的影响[J]. 金属热处理, 2022, 47(4): 189-195.
[14]	王瑞琴, 葛鹏, 廖强, 侯鹏, 刘宇. 固溶冷却方式对短时用高温钛合金板材组织和性能的影响[J]. 金属热处理, 2022, 47(4): 196-198.
[15]	王绍灼, 孟晗, 王芬, 樊海卫, 李燕, 唐超. 改善低氧TC4-LC及重熔TC4钛合金性能的热处理工艺[J]. 金属热处理, 2022, 47(4): 204-207.