配分时间对Q&P钢组织及性能的影响

doi:10.13251/j.issn.0254-6051.2020.09.010

金属热处理 ›› 2020, Vol. 45 ›› Issue (9): 62-65.DOI: 10.13251/j.issn.0254-6051.2020.09.010

配分时间对Q&P钢组织及性能的影响

陈梦园, 刘卓, 吴润, 吴腾

武汉科技大学材料与冶金学院,湖北武汉 430080

收稿日期:2020-03-31 出版日期:2020-09-25 发布日期:2020-12-29
通讯作者: 吴润,教授,博士,E-mail:runwu@wust.edu.cn
作者简介:陈梦园(1997—),女,硕士研究生,主要研究方向为QP钢的组织性能,E-mail:2338732489@qq.com

Effect of partitioning time on microstructure and properties of Q&P steel

Chen Mengyuan, liu Zhuo, Wu Run, Wu Teng

School of Materials and Metallurgy Engineering,W uhan University of Science and Technology,W uhan Hubei 430080,China

Received:2020-03-31 Online:2020-09-25 Published:2020-12-29

摘要/Abstract

摘要： 在传统C-Mn-Si钢的基础上,采用在线热处理,并通过光学显微镜、扫描电镜、拉伸试验等对一步淬火配分处理后试验钢的微观组织及力学性能进行了研究,且讨论了配分时间对材料组织性能的影响。结果表明:试验钢组织由板条马氏体和残留奥氏体组成,随着配分时间的增加,也有少量贝氏体生成,残留奥氏体含量先上升后下降,马氏体的板条组织逐渐模糊并软化;抗拉强度和屈服强度都逐渐降低,伸长率先升高后降低。配分30 s时综合性能最佳,抗拉强度为989 MPa,伸长率为23.5%,强塑积达到23.24 GPa·%。

关键词: 配分时间, Q& P钢, 残留奥氏体, 微观结构, 性能

Abstract: On the basis of the traditional C-Mn-Si steel,the microstructure and mechanical properties of the experimental Q&P steel after on-line one-step quenching and partitioning treatment were studied by metallographic microscope,scanning electron microscope and tensile test.The effect of partitioning time on the microstructure and properties of the steel was also discussed.The results show that the experimental steel structure consists of lath martensite and retained austenite.With the increase of partitioning time,a small amount of bainite is formed,and the retained austenite content first rises and then falls,and the lath structure of martensite is gradually blurred and softened;the tensile strength and yield strength are gradually reduced,and the elongation first increases and then decreases.The best comprehensive performance is achieved under the partitioning time of 30 s,the tensile strength is 989 MPa,the elongation is 23.5%,and the product of strength and elongation is 23.24 GPa·%.

Key words: partitioning time, Q&P steel, retained austenite, microstructure, properties

中图分类号:

TG124.4

陈梦园, 刘卓, 吴润, 吴腾. 配分时间对Q&P钢组织及性能的影响[J]. 金属热处理, 2020, 45(9): 62-65.

Chen Mengyuan, liu Zhuo, Wu Run, Wu Teng. Effect of partitioning time on microstructure and properties of Q&P steel[J]. Heat Treatment of Metals, 2020, 45(9): 62-65.

参考文献

[1] Speer J G,Edmonds D V,Rizzo F C,et al.Partitioning of carbon from supersaturated plates of ferrite,with application to steel processing and fundamentals of the bainite transformation[J].Current Opinion in Solid State and Materials Science,2004,8(3/4):219-237.
[2] Speer J G,Streicher A M,Matlock D K,et al.Quenching and partitioning:A fundamentally new process to create high strength TRIP sheet microstructures[C]//Symposium on the Thermodynamics,Kinetics,Characterization and Modeling of Austenite Formation and Decomposition.Chicage:Minerals Metal and Mater,2003:505-522.
[3] Speer J G,Rizzo F C,Matlock D K,et al.The "quenching and partitioning" process:Background and recent progress[J].Materials Research,2005,8(4):417-423.
[4] Speer J G,Matlock D K,Moor E D,et al.Highlights of recent progress in automotive sheet steel development[J].World Iron and Steel,2013,13(5):48-54.
[5] Matlock D K,Speer J G.Microstructure and Texture in Steels—Third Generation of AHSS:Microstructure Design Concepts[M].London:Springer,2009:185-205.
[6] 徐祖耀.淬火-碳分配-回火(Q-P-T)工艺浅介[J].金属热处理,2009,34(6):1-8.
Xu Zuyao.A brief introduction to quenching-partitioning-tempering(Q-P-T)process[J].Heat Treatment of Metals,2009,34(6):1-8.
[7] 王建军,焦贵鹏,刘沿东.Q&P热处理工艺对C-Si-Mn钢组织性能的影响[J].材料热处理学报,2013,34(3):104-107.
Wang Jianjun,Jiao Guipeng,Liu Yandong.Influence of quenching and partitioning process on microstructure and properties of a C-Si-Mn steel[J].Transactions of Materials and Heat Treatment,2013,34(3):104-107.
[8] 董辰,陈雨来,江海涛.超高强Q&P钢淬火温度对组织和性能的影响[J].热加工工艺,2009,38(12):121-123.
Dong Chen,Chen Yulai,Jiang Haitao.Influence of quenching temperature on microstructure and mechanical properties of Q&P super-high strength steel[J].Hot Working Technology,2009,38(12):121-123.
[9] Sun J,Yu H.Microstructure development and mechanical properties of quenching and partitioning(Q＆P)steel and an incorporation of hot dipping galvanization during Q＆P process[J].Materials Science and Engineering A,2013,586(1):100-107.
[10] Moor E D,Lacroix S,Clarke A J,et al.Effect of retained austenite stabilized via quench and partitioning on the strain hardening of martensitic steels[J].Metallurgical and Materials Transactions A,2008,39(11):2586-2595.
[11] 李阳,吕宇鹏,李士同.钢的淬火-分配(Q-P)处理研究现状与进展[J].金属热处理,2010,35(4):65-68.
Li Yang,Lü Yupeng,Li Shitong.Study status and progress of quenching and partitioning(Q-P)heat treatment for steel[J].Heat Treatment of Metals,2010,35(4):65-68.
[12] 胡淑娥,孙卫华,许云波.超快冷工艺对超高强钢组织性能的影响[J].四川冶金,2015,37(1):29-36.
Hu Shue,Sun Weihua,Xu Yunbo.Effects of ultra-fast cooling on properties and microstructure of ultra-high strength steel[J].Sichuan Metallurgy,2015,37(1):29-36.

[1]	王玉岱, 刘洋, 朱言言, 田象军, 程序, 冉先喆, 钱婷婷. 热处理对复合制造AerMet100超高强度钢组织均匀性与拉伸性能的影响[J]. 金属热处理, 2022, 47(4): 1-9.
[2]	张子延, 陈君, 陈晓亚, 李全安, 刘建鑫. 固溶时效处理对Mg-4Sm-3Gd-0.5Zr合金显微组织和耐蚀性能的影响[J]. 金属热处理, 2022, 47(4): 10-16.
[3]	梁恩溥, 徐乐, 杨勇, 王毛球. 添加Al、Cu对40CrNi3MoV钢组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 17-23.
[4]	祁晓亮, 李岩, 定巍, 赵增武. 含Al中锰TRIP钢原始组织对临界退火后组织与力学性能的影响[J]. 金属热处理, 2022, 47(4): 24-29.
[5]	陈保安, 张静媛, 祝志祥, 韩钰, 潘学东, 张磊, 陈素红. 化学成分对高强Al-Mg-Si合金组织和性能的影响[J]. 金属热处理, 2022, 47(4): 30-38.
[6]	陈东俊, 李广阳, 刘刚. 时效处理对AlSi9Cu3压铸铝合金组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 53-56.
[7]	陈连生, 张露友, 田亚强, 杨子旋, 李红斌, 潘红波, 魏英立. 低碳高强舰船用钢的CCT曲线及其组织性能[J]. 金属热处理, 2022, 47(4): 63-68.
[8]	王云龙, 余伟, 张昳, 史佳新, 李明辉. 奥氏体化温度对贝氏体钢等温转变及力学性能的影响[J]. 金属热处理, 2022, 47(4): 80-85.
[9]	陈思君, 陈送义, 陈庚, 袁丁玲, 陈康华. Mg含量对2A14铝合金组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 86-92.
[10]	骆再斌, 范子泽, 彭振. 轻质高熵合金的研究进展[J]. 金属热处理, 2022, 47(4): 100-107.
[11]	白青青, 张志宏, 郑淮北, 王英虎. 2507超级双相不锈钢中σ相的析出行为[J]. 金属热处理, 2022, 47(4): 108-115.
[12]	陈刚, 罗小兵, 柴锋, 杨才福, 张正延, 杨丽. 轧制加热温度对高强度低合金钢组织及冲击性能的影响[J]. 金属热处理, 2022, 47(4): 116-121.
[13]	李立, 曾艳, 吴晓春. 4Cr5Mo2VCo钢的热处理工艺优化[J]. 金属热处理, 2022, 47(4): 133-140.
[14]	吕杰晟, 宋志刚, 何建国, 丰涵, 郑文杰, 朱玉亮. S32205双相不锈钢冷轧退火组织转变及强塑化机理分析[J]. 金属热处理, 2022, 47(4): 141-145.
[15]	王琪, 吴光亮. 回火温度对1100 MPa级高强钢组织与性能的影响[J]. 金属热处理, 2022, 47(4): 146-150.

配分时间对Q&P钢组织及性能的影响

Effect of partitioning time on microstructure and properties of Q&P steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价