逆转变奥氏体对中Mn钢低温冲击断裂过程的影响

doi:10.13251/j.issn.0254-6051.2021.11.023

金属热处理 ›› 2021, Vol. 46 ›› Issue (11): 147-151.DOI: 10.13251/j.issn.0254-6051.2021.11.023

逆转变奥氏体对中Mn钢低温冲击断裂过程的影响

李敬, 杨跃辉, 张晓娟, 梁国俐, 苑少强

唐山学院河北省智能装备数字化设计及过程仿真重点实验室, 河北唐山 063000

收稿日期:2021-05-28 出版日期:2021-11-25 发布日期:2021-12-08
作者简介:李敬(1979—),女,副教授,博士,主要研究方向为新钢铁材料的开发及工艺,E-mail:lijing318@126.com
基金资助:
河北省高端钢铁冶金联合研究基金(E2019105101);唐山市科技计划(18130218a)

Effect of reversed austenite on low temperature impact fracture process of medium Mn steel

Li Jing, Yang Yuehui, Zhang Xiaojuan, Liang Guoli, Yuan Shaoqiang

Key Lab of Intelligent Equipment Digital Design and Process Simulation, Hebei Province, Tangshan University, Tangshan Hebei 063000, China

Received:2021-05-28 Online:2021-11-25 Published:2021-12-08

摘要/Abstract

摘要： 对超低碳7%Mn钢进行了不同温度的回火处理,测定了组织中的逆转变奥氏体含量及其在-60、-100 ℃下的冲击吸收能量,并观察了冲击断口附近的显微组织,进而讨论了逆转变奥氏体含量及稳定性对试验钢低温冲击断裂过程的影响。结果表明:逆转变奥氏体对试验钢低温韧性的影响具有两面性,一方面能够通过相变缓解裂纹尖端的应力集中,改善钢的低温韧性,另一方面,当其稳定性较低时易于在应力作用下大量发生马氏体相变,导致钢低温韧性降低。冲击断口附近产生明显塑性变形的区域都较小,表明在冲击断裂过程中难以通过大范围的TRIP效应实现韧化。

关键词: 逆转变奥氏体, 中Mn钢, 低温韧性, 断裂机制

Abstract: Ultra low carbon 7%Mn steel was tempered at different temperatures and the content of reversed austenite in the steel and the impact absorbed energy at -60 ℃ and -100 ℃ were measured, and the microstructure near impact fracture was observed, then the effects of content and stability of reversed austenite on low temperature impact fracture process of the tested steel were discussed. The results show that the effect of reversed austenite on low temperature toughness of the tested steel has pros and cons. It can alleviate the stress concentration at the crack tip and improve the low temperature toughness of the steel through phase transformation. On the other hand, when the stability of reversed austenite is lower, a large amount of reversed austenite can transform to martensite easily under stress, resulting in the reduction of low temperature toughness. The plastic deformation area near the impact fracture is small, which indicates that it is difficult to achieve toughening by a wide range TRIP effect during impact fracture.

Key words: reversed austenite, medium Mn steel, low temperature toughness, fracture mechanism

中图分类号:

TG142.1

李敬, 杨跃辉, 张晓娟, 梁国俐, 苑少强. 逆转变奥氏体对中Mn钢低温冲击断裂过程的影响[J]. 金属热处理, 2021, 46(11): 147-151.

Li Jing, Yang Yuehui, Zhang Xiaojuan, Liang Guoli, Yuan Shaoqiang. Effect of reversed austenite on low temperature impact fracture process of medium Mn steel[J]. Heat Treatment of Metals, 2021, 46(11): 147-151.

参考文献

[1]蓝秀琼, 陈建华. 回火温度对PRO500超高强钢的组织与冲击断裂行为的影响[J]. 材料热处理学报, 2020, 41(8): 80-86.
Lan Xiuqiong, Chen Jianhua. Effect of tempering temperature on microstructure and impact fracture behavior of PRO500 ultra-high strength steel[J]. Transactions of Materials and Heat Treatment, 2020, 41(8): 80-86.
[2]冯祥利, 王磊, 刘杨. 焊接工艺对Q460钢CO₂气体保护焊接头冲击断裂行为的影响[J]. 材料热处理学报, 2018, 39(3): 159-166.
Feng Xiangli, Wang Lei, Liu Yang. Effect of welding technology on impact fracture behavior of Q460 steel CO₂ gas shielded arc welding joints[J]. Transactions of Materials and Heat Treatment, 2018, 39(3): 159-166.
[3]杨跃辉, 张晓娟, 苑少强. 回转奥氏体对9Ni钢低温断裂机制的影响[J]. 材料热处理学报, 2014, 35(9): 101-105.
Yang Yuehui, Zhang Xiaojuan, Yuan Shaoqiang. Effect of reversed austenite on low temperature fracture mechanism of 9Ni steel[J]. Transactions of Materials and Heat Treatment, 2014, 35(9): 101-105.
[4]潘建华. 冲击载荷作用下压力容器用金属材料动态断裂行为的研究[D]. 合肥: 中国科学技术大学, 2019.
Pan Jianhua. Dynamic fracture behavior of pressure vessel metal materials under impact loads[D]. Hefei: University of Science and Technology of China, 2019.
[5]李小陶. 示波冲击曲线浅析[J]. 理化检验(物理分册), 2020, 56(10): 18-21.
Li Xiaotao. Analysis of oscillographic impact curve[J]. Physical Testing and Chemical Analysis (Part A: Physical Testing), 2020, 56(10): 18-21.
[6]白光, 曲迎东, 李荣德, 等. 7075合金低温冲击过程中的能量分布和示波曲线分析[J]. 特种铸造及有色合金, 2019, 39(7): 800-802.
Bai Guang, Qu Yingdong, Li Rongde, et al. Analysis of energy distribution and oscillographic curve of 7075 alloy during low temperature impact[J]. Special Casting and Nonferrous Alloys, 2019, 39(7): 800-802.
[7]Rautioaho R, Karjalainen P. Stress response of barkhausen noise and coercive force in 9Ni steel[J]. Journal of Magnetism and Magnetic Materials, 1987, 68: 321-327.
[8]李华瑞. 材料X射线衍射分析使用方法[M]. 北京: 冶金工业出版社, 1994: 39-48.
[9]Yan N, Di H S, Misra R D K, et al. Enhancing austenite stability in a new medium-Mn steel by combining deep cryogenic treatment and intercritical annealing: An experimental and theoretical study[J]. Materials Science and Engineering A, 2019, 753: 11-21.
[10]杨跃辉. 9Ni钢断裂过程中的裂纹扩展行为[J]. 金属热处理, 2015, 40(12): 177-180.
Yang Yuehui. Propagation behavior of crack in 9Ni steel during fracture process[J]. Heat Treatment of Metals, 2015, 40(12): 177-180.
[11]李会鹏, 熊毅, 路妍, 等. 应变速率对低温拉伸316LN奥氏体不锈钢微观组织和力学性能的影响[J]. 材料研究学报, 2018, 32(2): 105-111.
Li Huipeng, Xiong Yi, Lu Yan, et al. Effect of strain rate on microstructure evolution and mechanical property of 316LN austenitic stainless steel at cryogenic temperature[J]. Chinese Journal of Materials Research, 2018, 32(2): 105-111.
[12]郭宁, 王通, 徐虹, 等. TRIP效应主要影响因素的研究[J]. 汽车工艺与材料, 2016(2): 45-49.
Guo Ning, Wang Tong, Xu Hong, et al. A study on the main influencing factors of TRIP effect[J]. Automobile Technology and Material, 2016(2): 45-49.
[13]卫品官, 黄澍, 周磊, 等. 应变率对高强度TRIP力学性能的影响[J]. 热加工工艺, 2010, 39(16): 49-51.
Wei Pinguan, Huang Zhu, Zhou Lei, et al. Effect of strain rate on mechanical properties of high strength TRIP steel[J]. Hot Working Technology, 2010, 39(16): 49-51.
[14]He Zhongping, He Yanlin, Ling Yuntao, et al. Effect of strain rate on deformation behavior of TRIP steels[J]. Journal of Materials Processing Technology, 2012, 212(10): 2141-2147.
[15]Huh Hoon, Kin Seok-Bong, Song Jung-Han, et al. Dynamic tensile characteristics of TRIP-type and DP-type steels for an auto-body[J]. International Journal of Mechanical Science, 2008, 50: 918-931.
[16]阳锋, 罗海文, 董瀚. 退火温度对冷轧7Mn钢拉伸行为的影响及模拟研究[J]. 金属学报, 2018, 54(6): 859-867.
Yang Feng, Luo Haiwen, Dong Han. Effects of intercritical annealing temperature on the tensile behavior of cold rolled 7Mn steel and the constitutive modeling[J]. Acta Metallurgica Sinica, 2018, 54(6): 859-867.

逆转变奥氏体对中Mn钢低温冲击断裂过程的影响

Effect of reversed austenite on low temperature impact fracture process of medium Mn steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	邱旭扬帆, 杨卓越, 丁雅莉. 提高Cr-Ni-Mo-Ti马氏体时效不锈钢超低温韧性的固溶处理工艺[J]. 金属热处理, 2022, 47(1): 44-48.
[2]	齐祥羽, 严玲, 李广龙, 李文斌, 杜林秀. 逆转变奥氏体稳定性对中锰钢强韧性的影响[J]. 金属热处理, 2021, 46(9): 205-210.
[3]	邱旭扬帆, 杨卓越, 丁雅莉. 残留/逆转变奥氏体对改善高强度不锈钢-196 ℃超低温冲击性能的影响[J]. 金属热处理, 2021, 46(5): 71-74.
[4]	肖娜, 徐晓宁, 王益民, 孙永辉, 田勇. 回火温度对EH460级船用中厚钢板组织与强韧性的影响[J]. 金属热处理, 2021, 46(5): 81-86.
[5]	李明兵, 王新南, 商国强, 祝力伟, 李静, 李星, 朱知寿. TC32钛合金不同热处理工艺下的组织性能及断裂机制[J]. 金属热处理, 2021, 46(4): 112-117.
[6]	邓伟, 秦小梅. 临界淬火工艺处理高强结构钢Q690GJ的韧化机理[J]. 金属热处理, 2021, 46(12): 247-251.
[7]	吉昱睿, 杨卓越, 谭红琳, 丁雅莉. 预处理温度对Cr-Ni-Co-Mo马氏体时效不锈钢强度的影响[J]. 金属热处理, 2021, 46(11): 170-173.
[8]	吉昱睿, 杨卓越, 谭红琳, 丁雅莉. 提高Cr-Ni-Co-Mo马氏体时效不锈钢超低温韧性的热处理工艺[J]. 金属热处理, 2021, 46(10): 133-136.
[9]	杨跃辉, 苑少强, 梁国俐, 王竚. 回火温度对超低碳7%Mn钢组织与性能的影响[J]. 金属热处理, 2021, 46(10): 168-172.
[10]	刘海生, 李敬, 王会刚, 杨跃辉, 刘金旭, 武会宾. 热处理对不同碳含量3.5Ni钢力学性能和低温韧性的影响[J]. 金属热处理, 2021, 46(10): 182-186.
[11]	牛延龙, 刘岩松, 刘清友, 贾书君, 童帅, 汪兵. 针状铁素体管线钢的低温韧性与“有效晶粒尺寸”的新定义[J]. 金属热处理, 2020, 45(7): 101-110.
[12]	杨晰, 苏春霞, 陈本文, 李培兴, 高山, 李福坤. 回火温度对铬镍合金结构钢组织性能的影响[J]. 金属热处理, 2020, 45(2): 105-107.
[13]	刘文斌, 战国锋, 黄峰. 回火温度对7Ni钢组织和性能的影响[J]. 金属热处理, 2020, 45(12): 63-68.
[14]	付航, 梁小凯, 孙新军, 黄涛. 新型纳米强化马奥复相钢的应力腐蚀行为[J]. 金属热处理, 2020, 45(12): 160-168.
[15]	姜在伟, 吴俊平, 张仪杰, 宁博, 李志超. 低温容器用07MnNiMoDR钢的热处理优化[J]. 金属热处理, 2020, 45(11): 182-186.