固溶处理温度对Fe-Mn-Al-C铁素体基轻质钢耐蚀性能的影响

doi:10.13251/j.issn.0254-6051.2021.04.018

金属热处理 ›› 2021, Vol. 46 ›› Issue (4): 105-111.DOI: 10.13251/j.issn.0254-6051.2021.04.018

固溶处理温度对Fe-Mn-Al-C铁素体基轻质钢耐蚀性能的影响

赵婷¹, 孙佳振¹, 贾鑫¹, 郭凯¹, 王天生^1,2

1.燕山大学亚稳材料制备技术与科学国家重点实验室, 河北秦皇岛 066004;
2.燕山大学国家冷轧板带装备及工艺工程技术研究中心, 河北秦皇岛 066004

收稿日期:2020-10-08 出版日期:2021-04-25 发布日期:2021-05-08
通讯作者: 王天生(1963—),男,教授,博士,主要研究方向为金属材料的强韧化,E-mail:tswang@ysu.edu.cn
作者简介:赵婷(1991—),女,博士研究生,主要研究方向为Fe-Mn-Al-C低密度轻质钢和低温贝氏体钢的强韧化,E-mail:ting0505ha@163.com。

Influence of solution temperature on corrosion resistance of Fe-Mn-Al-C ferrite based light weight steel

Zhao Ting¹, Sun Jiazhen¹, Jia Xin¹, Guo Kai¹, Wang Tiansheng^1,2

1. State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao Hebei 066004, China;
2. National Engineering Research Center for Equipment and Technology of Cold Strip Rolling, Yanshan University, Qinhuangdao Hebei 066004, China

Received:2020-10-08 Online:2021-04-25 Published:2021-05-08

摘要/Abstract

摘要： 利用光学显微镜、扫描电镜、X射线衍射仪等研究了热轧态、850、950和1 050 ℃固溶处理Fe-Mn-Al-C铁素体基轻质钢的微观组织。通过测试固溶处理试样的极化曲线和阻抗曲线,以及观察试样在3.5%NaCl溶液中腐蚀后的表面状态,分析其耐蚀性。结果表明,试样经850 ℃固溶处理后的组织为铁素体+κ碳化物;950 ℃固溶处理后组织为铁素体+奥氏体+少量κ碳化物;1050 ℃固溶处理后组织为铁素体+奥氏体。随固溶处理温度的升高,试样中κ碳化物逐渐粗化直至全部溶解,950 ℃时发生奥氏体转变且晶粒有所增大,但1050 ℃时奥氏体的含量却略有降低。950 ℃固溶处理试样在3.5%NaCl溶液中的耐蚀性最佳,其自腐蚀电流密度为3.102×10^-6 A/cm²,钝化膜的电阻R_p值为3944 Ω。经过240 h腐蚀浸泡后,950 ℃固溶处理试样的腐蚀速率最低,这主要是由于其组织中奥氏体含量相对较高、铁素体和κ碳化物含量相对较低以及铁素体中Al元素含量较高所致。

关键词: Fe-Mn-Al-C铁素体基轻质钢, 固溶处理, 微观组织, 耐蚀性

Abstract: Microstructure of a Fe-Mn-Al-C ferrite based lightweight steel after hot-rolling and solution treatment at 850, 950 and 1050 ℃, respectively, were analysed by means of OM, SEM and X-ray diffractometer. The corrosion resistance of the solution treated samples were studied by obtaining the polarization curves, impedance curves and the surface states corrosion in 3.5%NaCl solution. The results show that the microstructure after solution treatment at 850, 950 and 1050 ℃ are ferrite+ κ carbide, ferrite+ austenite+ a little κ carbide and ferrite+ austenite, respectively. With the solution treatment temperature increasing, κ carbides coarse gradually until dissolve completely, austenite forms and the grain grows, but the amount of the austenite decreases slightly. The best corrosion resistance in 3.5%NaCl solution is obtained after solution treatment at 950 ℃, which self corrosion current density is 3.102×10^-6 A/cm² and resistance R_p value of passivation film is 3944 Ω, the corrosion rate is lowest after corrosion test for 240 h. All of that is mainly due to the higher content of austenite and Al in ferrite as well as the lower content of ferrite and κ carbide.

Key words: Fe-Mn-Al-C ferrite based ligh tweight steel, solution treatment, microstructure, corrosion resistance

中图分类号:

TG172.5

赵婷, 孙佳振, 贾鑫, 郭凯, 王天生. 固溶处理温度对Fe-Mn-Al-C铁素体基轻质钢耐蚀性能的影响[J]. 金属热处理, 2021, 46(4): 105-111.

Zhao Ting, Sun Jiazhen, Jia Xin, Guo Kai, Wang Tiansheng. Influence of solution temperature on corrosion resistance of Fe-Mn-Al-C ferrite based light weight steel[J]. Heat Treatment of Metals, 2021, 46(4): 105-111.

参考文献

[1] 刘少尊,厉勇,王春旭,等.固溶处理对Fe-Mn-Al-C系低密度钢组织与性能的影响[J].金属热处理,2015,40(9):120-124.
Liu Shaozun,Li Yong,Wang Chunxu,et al.Effect of solution treatment on microstructures and properties of Fe-Mn-Al-C low density steel[J].Heat Treatment of Matals,2015,40(9):120-124.
[2] Wu Zhiqiang,Tang Yubo,Chen Wei,et al.Exploring the influence of Al content on the hot deformation behavior of Fe-Mn-Al-C steels through 3D processing map[J].Vacuum,2019,159:447-455.
[3] Shen Yaozu,Liu Jianhua,Yang Shufeng,et al.Dendrite growth behavior in directionally solidified Fe-C-Mn-Al alloys[J].Journal of Crystal Growth,2019,511:118-126.
[4] Li Zhuang,Wang Yingchun,Cheng Xingwang,et al.Compressive behavior of a Fe-Mn-Al-C lightweight steel at different strain rates[J].Materials Science and Engineering A,2020,772:138700.
[5] 倪呈军,刘营凯,王白冰,等.Fe-15Mn-10Al-0.3C钢升温过程中κ-碳化物的析出行为研究[J].上海金属,2019,41(3):18-24.
Ni Chengjun,Liu Yingkai,Wang Baibing,et al.Precipitation behavior of κ-carbide during heating process in Fe-15Mn-10Al-0.3C steel[J].Shanghai Metals,2019,41(3):18-24.
[6] Tonizzo Q,Gourgues-Lorenzon A,Maziere M,et al.Microstructure,plastic flow and fracture behavior of ferrite-austenite duplex low density medium Mn steel[J].Materials Science and Engineering A,2017,706:217-226.
[7] Haghdadi N,Zarei-Hanzaki A,Farabi E,et al.Strain rate dependence of ferrite dynamic restoration mechanism in a duplex low-density steel[J].Materials and Design,2017,132:360-366.
[8] Li Yangqi,Liu Mingxiang,Zhang Haiming,et al.Study of the influence of δ-ferrite on the TRIP effect of a low-density high aluminum steel by using full-field crystal plasticity modeling[J].Materials Science and Engineering A,2020,772:138667.
[9] Liu Mingxiang,Li Yangqi,Cui Zhenshan,et al.High ductility of spray formed low density TRIP steel with the improvement of δ-ferrite matrix[J].Materials Characterization,2019,156:109828.
[10] Kalantari A,Zarei-Hanzakia A,Abedi H,et al.Microstructure evolution and room temperature mechanical properties of a thermomechanically processed ferrite-based low density steel[J].Materials Science and Engineering A,2019,754:57-67.
[11] Seol J,Raabe D,Choi P,et al.Direct evidence for the formation of ordered carbides in a ferrite-based low-density Fe-Mn-Al-C alloy studied by transmission electron microscopy and atom probe tomography[J].Scripta Materialia,2013,68(6):348-353.
[12] Zhao Chao,Song Renbo,Zhang Leifeng,et al.Effect of annealing temperature on the microstructure and tensile properties of Fe-10Mn-10Al-0.7C low-density steel[J].Materials and Design,2016,91:348-360.
[13] Sohn S,Lee B,Lee S,Et al.Effect of annealing temperature on microstructural modification and tensile properties in 0.35C-3.5Mn-5.8Al lightweight steel[J].Acta Materialia,2013,61:5050-5066.
[14] 邢珊珊,戚浩宇,郑传波.固溶处理对 2205 双相不锈钢组织及钝化膜特性的影响[J].金属热处理,2020,45(3):146-150.
Xing Shanshan,Qi Haoyu,Zheng Chuanbo.Effect of solution treatment on microstructure and passivation film properties of 2205 duplex stainless steel[J].Heat Treatment of Metals,2020,45(3):146-150.
[15] Lins V,Freitas M,Paula M.Corrosion resistance study of Fe-Mn-Al-C alloys using immersion and potentiostatic tests[J].Applied Surface Science,2005,250:124-134.
[16] Fajardo S,Llorente I,Jimenez J,et al.Effect of Mn additions on the corrosion behaviour of TWIP Fe-Mn-Al-Si austenitic steel in chloride solution[J].Corrosion Science,2019,154:246-253.
[17] Wang Chaurjeng,Chang Yeongchung.NaCl-induced hot corrosion of Fe-Mn-Al-C alloys[J].Materials Chemistry and Physics,2002,76:151-161.
[18] Yuan Xiaoyun,Zhao Yang,Li Xing,et al.Effect of Cr on mechanical properties and corrosion behaviors of Fe-Mn-C-Al-Cr-N TWIP steels[J].Journal of Materials Science and Technology,2017,33:1555-1560.
[19] William A,Jorge H,Juan D.Evaluation of erosion-corrosion resistance in Fe-Mn-Al austenitic steels[J].Materials Research,2013,16(2):447-452.
[20] 曹楚南,张鉴清.电化学阻抗谱导论[M].北京:科学出版社,2002:177-191.
[21] 张春亚,张奇,李继高,等.碳钢及低合金钢在氯离子溶液中夹杂物诱发点蚀位置显微腐蚀实验探讨[J].冶金分析,2014,34(1):22-27.
Zhang Chunya,Zhang Qi,Li Jigao,et al.Experimental study on pitting corrosion of carbon steel and low alloy steel induced by inclusions in chloride solution[J].Metallurgical Analysis,2014,34(1):22-27.
[22] Wan Hongxia,Cai Yong,Song Dongdong,et al.Effect of Cr/Mo carbides on corrosion behaviour of Fe-Mn-C twinning induced plasticity steel[J].Corrosion Science,2020,167:108518.
[23] Ruscak M,Perng T.Effect of ferrite on corrosion of Fe-Mn-Al Alloys in sodium chloride solution[J].Corrosion Science,1995,51:738-743.
[24] Zhang Y S,Zhu X M,Zhong S H.Effect of alloying elements on the electrochemical polarization behavior and passive film of Fe-Mn base alloys in various aqueous solutions[J].Corrosion Science,2004,46:853-876.

固溶处理温度对Fe-Mn-Al-C铁素体基轻质钢耐蚀性能的影响

Influence of solution temperature on corrosion resistance of Fe-Mn-Al-C ferrite based light weight steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	张子延, 陈君, 陈晓亚, 李全安, 刘建鑫. 固溶时效处理对Mg-4Sm-3Gd-0.5Zr合金显微组织和耐蚀性能的影响[J]. 金属热处理, 2022, 47(4): 10-16.
[2]	陈保安, 张静媛, 祝志祥, 韩钰, 潘学东, 张磊, 陈素红. 化学成分对高强Al-Mg-Si合金组织和性能的影响[J]. 金属热处理, 2022, 47(4): 30-38.
[3]	王英虎, 郑淮北, 刘庭耀, 宋令玺, 白青青. 固溶处理对53Cr21Mn9Ni4N耐热钢组织及碳化物的影响[J]. 金属热处理, 2022, 47(4): 39-45.
[4]	陈东俊, 李广阳, 刘刚. 时效处理对AlSi9Cu3压铸铝合金组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 53-56.
[5]	李立, 曾艳, 吴晓春. 4Cr5Mo2VCo钢的热处理工艺优化[J]. 金属热处理, 2022, 47(4): 133-140.
[6]	张骥俊, 邢彦锋, 曹菊勇. 超声振动对CMT电弧增材制造铝合金组织与性能的影响[J]. 金属热处理, 2022, 47(4): 159-164.
[7]	王瑞琴, 葛鹏, 廖强, 侯鹏, 刘宇. 固溶冷却方式对短时用高温钛合金板材组织和性能的影响[J]. 金属热处理, 2022, 47(4): 196-198.
[8]	孙建, 黄贞益, 李景辉, 王萍. 固溶和时效处理对Fe-Mn-Al-C轻质钢组织和硬度的影响[J]. 金属热处理, 2022, 47(3): 34-38.
[9]	杨春苗, 王珊, 王淑慧, 李延珍, 刘文文. RRA过程中预时效时间对7A85铝合金组织性能的影响[J]. 金属热处理, 2022, 47(3): 44-47.
[10]	陈善勇, 王快社, 乔柯, 王文. 碱热处理对搅拌摩擦加工AZ31镁合金耐腐蚀性能的影响[J]. 金属热处理, 2022, 47(3): 61-66.
[11]	梅金娜, 姜凤阳, 卫娜, 刘浪浪, 思芳, 刘松涛, 王俊勃, 刘江南. 轧制变形对高熵合金微观组织和力学性能的影响[J]. 金属热处理, 2022, 47(3): 67-71.
[12]	程体娟, 甘斌, 于鸿垚, 周海晶, 郭彩玉, 毕中南, 杜金辉. 固溶处理对新型镍基高温合金组织及性能的影响[J]. 金属热处理, 2022, 47(3): 107-112.
[13]	叶拓, 唐明, 刘吉兆, 刘伟, 吴远志, 刘巍, 徐文. 固溶温度对7075铝合金板材组织与力学性能的影响[J]. 金属热处理, 2022, 47(3): 119-123.
[14]	叶拓, 何玉兵, 何文鹏, 刘巍, 袁浩登, 吴远志, 刘伟, 刘吉兆. 轧制态6082-T6铝合金的热压缩力学行为及微观组织分析[J]. 金属热处理, 2022, 47(2): 26-30.
[15]	闵旭东, 黄元春, 肖政兵, 刘宇, 任贤魏, 邹倜. 预处理对汽车用Al-Mg-Si合金组织和晶间腐蚀行为的影响[J]. 金属热处理, 2022, 47(2): 78-85.