热变形参数对316L/Q370qE复合板结合强度的影响

doi:10.13251/j.issn.0254-6051.2021.05.021

摘要/Abstract

摘要： 通过Gleeble-3800热压缩试验模拟316L/Q370qE复合板轧制,并借助拉伸试验、硬度试验、组织分析等手段,研究了变形量、变形温度、变形前保温时间等参数对界面结合强度的影响规律。结果表明:随着变形量的增加,结合强度逐渐升高,变形量大于20%时,结合强度升高趋势变缓;随着变形温度的升高,结合强度先升高后降低,1100 ℃与1250 ℃时结合强度相差不大;随着保温时间的延长,结合强度逐渐降低。

关键词: 复合板, 热变形参数, 结合强度

Abstract: Rolling process of the 316L/Q370qE clad plate was simulated by Gleeble-3800 thermal compression testing. And the influence of deformation amount, deformation temperature and holding time before deformation on bonding strength of the clad plate was studied by means of tensile testing, hardness testing and microstructure analysis. The results show that the bonding strength gradually increases with the increase of deformation amount, but the increasing trend becomes slower when the deformation amount is greater than 20%. As the deformation temperature increases, the bonding strength first increases and then decreases, and the bonding strength does not change much when the deformation temperature is 1100 ℃ and 1250 ℃. The longer the holding time, the lower the bonding strength of the clad plate is.

Key words: clad plate, hot deformation parameter, bonding strength

中图分类号:

TG142

邵春娟, 镇凡, 曲锦波, 雒广杰. 热变形参数对316L/Q370qE复合板结合强度的影响[J]. 金属热处理, 2021, 46(5): 132-137.

Shao Chunjuan, Zhen Fan, Qu Jinbo, Luo Guangjie. Influence of hot deformation parameters on bonding strength of 316L/Q370qE clad plate[J]. Heat Treatment of Metals, 2021, 46(5): 132-137.

参考文献

[1]李海斌, 黄庆学, 周存龙, 等. 热轧碳钢/不锈钢复合板结合界面碳钢的组织演变[J]. 材料热处理学报, 2014, 35(4): 57-61.
Li Haibin, Huang Qingxue, Zhou Cunlong, et al. Microstructure evolution of carbon steel at interface of carbon steel / stainless steel clad plate by hot rolling[J]. Transactions of Materials and Heat Treatment, 2014, 35(4): 57-61.
[2]王泽鹏, 张红梅, 付魁军, 等. 热轧304L/Q235B不锈钢复合板界面特征及性能分析[J]. 材料热处理学报, 2016, 37(S1): 44-49.
Wang Zepeng, Zhang Hongmei, Fu Kuijun, et al. Characteristics of bonding interface and analysis of properties of hot-rolled 304L/Q235B stainless steel clad plate[J]. Transactions of Materials and Heat Treatment, 2016, 37(S1): 44-49.
[3]曾周燏, 李东晖, 王青峰. 铁路桥梁用轧制不锈钢复合板的应用性研究[J]. 现代冶金, 2019, 47(1): 11-16.
[4]杨牧南, 左孝青, 赵明伟, 等. 不锈钢复合板制备技术研究进展[J]. 热加工工艺, 2012, 41(20): 93-96.
Yang Munan, Zuo Xiaoqing, Zhao Mingwei, et al. Research progress of manufacturing technology for stainless steel clad plate[J]. Hot Working Technology, 2012, 41(20): 93-96.
[5]金贺荣, 杨旭坤, 宜亚丽. 316L-Q345R不锈钢复合板性能评价[J]. 材料工程, 2016, 44(8): 104-110.
Jin Herong, Yang Xukun, Yi Yali. Performance evaluation of 316L-Q345R stainless steel clad plate[J]. Journal of Material Engineering, 2016, 44(8): 104-110.
[6]丁海民, 范孝良, 王进峰, 等. 热轧复合不锈钢-碳钢复合板界面特征[J]. 材料热处理学报, 2011, 32(11): 18-22.
Ding Haimin, Fan Xiaoliang, Wang Jinfeng, et al. Interface characterization of hot-rolled stainless steel/carbon steel clad[J]. Transactions of Materials and Heat Treatment, 2011, 32(11): 18-22.
[7]王小勇, 张海, 刘建明, 等. 热轧不锈钢复合板力学性能及工艺优化[J]. 中国冶金, 2018, 28(7): 24-27.
Wang Xiaoyong, Zhang Hai, Liu Jianming, et al. Mechanical properties and process optimization of hot rolled stainless clad steel plate[J]. China Metallurgy, 2018, 28(7): 24-27.
[8]王震, 叶静静, 张庆安, 等. 304/Q235B热轧复合板界面的显微组织特征[J]. 安徽工业大学学报, 2019, 36(2): 103-107.
Wang Zhen, Ye Jingjing, Zhang Qing'an, et al. Microstructure characteristics of interface in hot-rolled 304/Q235B clad plate[J]. Anhui University of Technology(Natural Science), 2019, 36(2): 103-107.
[9]曾周燏, 江姗, 李东晖. TMCP工艺轧制桥梁用不锈钢复合板的组织与性能[J]. 中国冶金, 2017, 27(6): 19-23.
Zeng Zhouyu, Jiang Shan, Li Donghui. Microstructure and properties of stainless steel clad plate used for bridge rolled by thermal mechanical control process[J]. China Metallurgy, 2017, 27(6): 19-23.
[10]金贺荣, 戴超, 段昌新, 等. 316L/EH40不锈钢复合板变形行为及初始层厚比设计[J]. 钢铁, 2018, 53(10): 46-53.
Jin Herong, Dai Chao, Duan Changxin, et al. Deformation behavior and initial thickness ratio design of 316L/EH40 stainless steel clad plate[J]. Iron and Steel, 2018, 53(10): 46-53.
[11]谢广明, 骆宗安, 王国栋. 轧制工艺对真空轧制复合钢板组织与性能的影响[J]. 钢铁研究学报, 2011, 23(12): 27-30.
Xie Guangming, Luo Zong'an, Wang Guodong. Effect of rolling parameters on microstructure and property of vacuum rolling clad steel plate[J]. Journal of Iron and Steel Research, 2011, 23(12): 27-30.
[12]于涛, 井玉安, 张亚樵, 等. 不锈钢复合板界面组织形貌[J]. 钢铁, 2018, 53(11): 63-69.
Yu Tao, Jing Yu'an, Zhang Yaqiao, et al. Interfacial microstructure morphologies of stainless steel clad plate[J]. Iron and Steel, 2018, 53(11): 63-69.
[13]金贺荣, 韩民峰, 段昌新. 压下率对316L/EH40复合板界面微观形貌的影响[J]. 钢铁, 2019, 54(12): 62-69.
Jin Herong, Han Minfeng, Duan Changxin. Deformation behavior and initial thickness ratio design of 316L/EH40 stainless steel clad plate[J]. Iron and Steel, 2019, 54(12): 62-69.
[14]金贺荣, 张春雷, 韩雪艳, 等. 热处理对316L/Q345不锈钢复合板显微组织与力学性能的影响[J]. 中国有色金属学报, 2015, 25(4): 952-958.
Jin Herong, Zhang Chunlei, Han Xueyan, et al. Effect of heat treatment on microstructure and mechanical properties of 316L/Q345R stainless steel clad plate[J]. The Chinese Journal of Nonferrous Metals, 2015, 25(4): 952-958.
[15]代响林, 刘宝玺, 马久乐, 等. 真空热轧法制备不锈钢复合板组织和力学性能[J]. 钢铁, 2017, 52(2): 65-70.
Dai Xianglin, Liu Baoxi, Ma Jiule, et al. Microstructure and mechanical properties of stainless steel clad plate fabricated by vacuum hot rolling[J]. Iron and Steel, 2017, 52(2): 65-70.
[16]李龙, 张心金, 刘会云, 等. 热轧不锈钢复合板界面氧化物夹杂的形成机制[J]. 钢铁研究学报, 2013, 25(1): 43-47.
Li Long, Zhang Xinjin, Liu Huiyun, et al. Formation mechanism of oxide inclusion on the interface of hot-rolled stainless steel clad plates[J]. Journal of Iron and Steel Research, 2013, 25(1): 43-47.
[17]李龙, 张心金, 祝志超, 等. 真空热轧不锈钢复合板界面结合行为的研究[J]. 材料与冶金学报, 2014, 13(1): 46-50.
Li Long, Zhang Xinjin, Zhu Zhichao, et al. Investigation on bonding of stainless steel clad plate by vacuum hot rolling[J]. Journal of Materials and Metallurgy, 2014, 13(1): 46-50.
[18]黄庆学, 杨小容, 周存龙, 等. 制坯工艺对热轧不锈钢/碳钢复合板复合效果的影响[J]. 材料热处理学报, 2014, 35(S1): 62-66.
Huang Qingxue, Yang Xiaorong, Zhou Cunlong, et al. Effect of reduction rate on microstructure and transformation behavior of carbon steel by rolling clad plate[J]. Transactions of Materials and Heat Treatment, 2014, 35(S1): 62-66.