激光功率对高速激光熔覆Ni/316L层组织与力学性能的影响

doi:10.13251/j.issn.0254-6051.2021.05.037

摘要/Abstract

摘要： 为研究高速激光熔覆Ni/316L层组织与力学性能随激光功率的演变规律,分别采用1.1、1.3 和1.5 kW激光功率在Q235钢表面熔覆Ni/316L层。采用扫描电镜(SEM)、能谱仪(EDS)、显微硬度计、冲击试验机及Knoop压痕法研究了熔覆层的显微组织、显微硬度、冲击性能与弹性模量。结果表明,激光功率为1.1 kW时熔覆层内部晶粒生长取向存在垂直于界面生长和与界面成一定角度交叉生长两种模式,并含有少量孔隙等缺陷,熔覆层/基体界面元素成断崖式分布,二者互扩散程度较低。随着激光功率升高,熔覆层晶粒转变为以垂直于界面生长为主,且涂层内部致密性高,缺陷较少,熔覆层/基体界面元素互扩散程度提升。激光功率对熔覆层硬度、冲击性能都存在显著影响,但是对弹性模量的影响较低。不同激光功率下,熔覆层最大硬度均出现在距界面100 μm左右的区域;功率从1.1 kW提升至1.5 kW时熔覆层熔合区最大硬度提高约50%;功率为1.5 kW时,试样的冲击性能较基体提高约20%。

关键词: 高速激光熔覆, 激光功率, 显微组织, 力学性能

Abstract: In order to evaluate the effect of laser power on microstructure and mechanical properties of the Ni/316L layer deposited via high-speed laser cladding, the Ni/316L layer was clad on the Q235 steel surface under laser power of 1.1, 1.3, and 1.5 kW respectively. The microstructure, Vickers hardness, impact property and elastic modulus of the laser clad layers were examined by means of scanning electron microscope (SEM), energy dispersive spectrometer (EDS), Vickers hardness tester, impact testing machine and Knoop indentation method. The results show that when the laser power is 1.1 kW, the grain growth in the laser clad layer contains perpendicular-to-interface growth mode and slant growth mode, the clad layer also has a small amount of pores and other defects, and the elements at the clad layer/substrate interface are distributed in a cliff-like manner, which means that the element diffusion between the substrate and the clad layer is limited. As the laser power increases, the perpendicular-to-interface growth mode of grains becomes the main mode, and the porosity of the clad layer is lower and the defect is less, the interdiffusion degree of elements at the clad layer/substrate interface is improved. The laser power has a significant effect on hardness and impact property of the clad layer, but has little effect on elastic modulus. The maximum hardness of the clad layer with different laser power is always about 100 μm away from the interface. When the laser power increases from 1.1 kW to 1.5 kW, the maximum hardness of the clad layer fusion zone is increased by about 50%, and the impact property of the clad layer specimen is about 20% higher than that of the substrate when the laser power is 1.5 kW.

Key words: high-speed laser cladding, laser power, microstructure, mechanical properties

中图分类号:

TG174.4

刘德来, 王博, 周攀虎, 董会, 鲍正宇. 激光功率对高速激光熔覆Ni/316L层组织与力学性能的影响[J]. 金属热处理, 2021, 46(5): 213-217.

Liu Delai, Wang Bo, Zhou Panhu, Dong Hui, Bao Zhengyu. Effect of laser power on microstructure and mechanical properties of high-speed laser clad Ni/316L layer[J]. Heat Treatment of Metals, 2021, 46(5): 213-217.

参考文献

[1]张小霓, 吴文龙, 常亮, 等. 一种发电机组热力系统腐蚀防护效果评价方法研究及应用[J]. 材料保护, 2019, 52(6): 143-148.
Zhang Xiaoni, Wu Wenlong, Chang Liang, et al. Research and application on evaluation method for corrosion prevention effect of thermodynamic system of a firepower generator unit[J]. Materials Protection, 2019, 52(6): 143-148.
[2]詹耀, 刘瑶, 于国利. 我国不同区域风电场的腐蚀环境及防腐技术分析[J]. 上海涂料, 2013, 51(10): 43-48.
Zhan Yao, Liu Yao, Yu Guoli. Analysis of the corrosion environment and corrosion protection technology of wind farm in different regions of China[J]. Shanghai Coatings, 2013, 51(10): 43-48.
[3]李承宇, 王会阳, 晁兵, 等. 风力发电设备防腐涂装[J]. 电镀与涂饰, 2011, 30(6): 70-72.
Li Chengyu, Wang Huiyang, Chao Bing, et al. Anti-corrosion coating of wind power equipment[J]. Electroplating and Finishing, 2011, 30(6): 70-72.
[4]丁紫阳, 马宗彬, 黎文强, 等. 激光熔覆Fe基合金粉末熔覆层的组织及性能研究[J]. 热加工工艺, 2019, 48(18): 100-102.
Ding Ziyang, Ma Zongbin, Li Wenqiang, et al. Study on microstructure and properties of laser cladding Fe-based alloy powder cladding layer[J]. Hot Working Technology, 2019, 48(18): 100-102.
[5]叶四友, 刘建永, 杨伟. 激光熔覆316L不锈钢涂层组织和性能的研究[J]. 表面技术, 2018, 47(3): 48-53.
Ye Siyou, Liu Jianyong, Yang Wei. Microstructure and properties of laser cladded 316L stainless steel layer[J]. Surface Technology, 2018, 47(3): 48-53.
[6]李利叶, 孙荣禄. 激光功率对熔覆Ni基复合涂层组织性能的影响[J]. 热加工工艺, 2016, 45(10): 182-186.
Li Liye, Sun Ronglu. Influence of laser power on microstructure and performance of Nickel-based composite coating[J]. Hot Working Technology, 2016, 45(10): 182-186.
[7]Li J N, Chen C Z, He Q S. Influence of Cu on microstructure and wear resistance of TiC/TiB/TiN reinforced composite fabricated by laser cladding[J]. Materials Chemistry and Physics, 2012, 133: 741-745.
[8]Liu J, Li J, Cheng X, et al. Effect of dilution and macro segregation on corrosion resistance of laser clad Aer-Met100 steel coating on 300M steel substrate[J]. Surface and Coatings Technology, 2017, 325: 352-359.
[9]董会, 韩燕, 付安庆, 等. 快速激光熔覆Ni/不锈钢堆焊层组织及耐蚀性能研究[J]. 表面技术, 2019, 48(5): 21-27.
Dong Hui, Han Yan, Fu Anqing, et al. Microstructure and corrosion resistance of Ni/stainless steel surfacing layer deposited via high-speed laser cladding[J]. Surface Technology, 2019, 48(5): 21-27.
[10]韩亚军, 陈友媛. 316L不锈钢在不同电导率海水和NaCl溶液中的电化学腐蚀行为[J]. 材料导报, 2012, 26(10): 57-60.
Han Yajun, Chen Youyuan. Electrochemistry corrosion behaviors of 316L stainless steel in different electric conductivity seawaters and NaCl solutions[J]. Materials Review, 2012, 26(10): 57-60.
[11]薛亚军. Ni-Cu-P镀层和316L不锈钢在热盐酸溶液中的耐蚀性及机制[J]. 金属热处理, 2013, 38(6): 114-117.
Xue Yajun. Corrosion resistance and its mechanism of Ni-Cu-P coating and 316L stainless steel in hot hydrochloric acid solution[J]. Heat Treatment of Metals, 2013, 38(6): 114-117.
[12]张自强, 程相榜, 白海明. 不同种类激光熔覆粉末的性能研究[J]. 南阳师范学院学报, 2018, 17(4): 22-29.
Zhang Ziqiang, Cheng Xiangbang, Bai Haiming. Study on the properties of different laser cladding powders[J]. Journal of Nanyang Normal University, 2018, 17(4): 22-29.
[13]杨健, 谢燕翔. 不锈钢激光熔敷纯Ni粉末涂层的组织和腐蚀行为[J]. 兵器材料科学与工程, 2018, 41(6): 34-39.
Yang Jian, Xie Yanxiang. Microstructure and corrosion behavior of pure Ni powder coating on stainless steel surface by laser cladding[J]. Ordnance Material Science and Engineering, 2018, 41(6): 34-39.
[14]吴金涛. 激光功率对2Cr13不锈钢激光熔覆涂层的影响[J]. 价值工程, 2017, 36(22): 213-215.
Wu Jintao. Effect of laser power on laser cladding coat of 2Cr13 stainless steel[J]. Value Engineering, 2017, 36(22): 213-215.
[15]陈小明, 姜志鹏, 张磊, 等. 激光功率对Ni基合金熔覆层的结构及性能影响[J]. 粉末冶金材料科学与工程, 2019, 24(4): 315-320.
Chen Xiaoming, Jiang Zhipeng, Zhang Lei, et al. Effects of laser power on microstructure and properties of Ni-based alloy cladding layers[J]. Materials Science and Engineering of Powder Metallurgy, 2019, 24(4): 315-320.
[16]柏树宏. 努氏压头确定织构取向和弹性模量方法研究[J]. 南方农机, 2015, 46(7): 27-28.
Bo Shuhong. Study on determination of texture orientation and elastic modulus by Knoop indenter[J]. China Southern Agricultural Machinery, 2015, 46(7): 27-28.
[17]王赛丽, 朱治刚. 不同激光功率对AZ31B镁合金表面Al-Cu合金熔覆层组织和性能的影响[J]. 热加工工艺, 2016, 45(8): 172-175.
Wang Saili, Zhu Zhigang. Influence of different laser power on microstructure and properties of Al-Cu cladding coating on AZ31B alloy[J]. Hot Working Technology, 2016, 45(8): 172-175.
[18]李轶楠, 姜文勇, 冯义成, 等. Cr含量对00CrxNi7Mo4.5N双相不锈钢组织和性能的影响[J]. 热加工工艺, 2016, 45(18): 98-101.
Li Yinan, Jiang Wenyong, Feng Yicheng, et al. Effect of Cr content on microstructure and properties of 00CrxNi7Mo4.5N duplex stainless steel[J]. Hot Working Technology, 2016, 45(18): 98-101.
[19]吕彦, 余圣甫, 行舒乐, 等. 钼、镍含量对马氏体不锈钢硬面药芯焊丝堆焊层组织和性能的影响[J]. 机械工程材料, 2013, 37(9): 29-32.
Lü Yan, Yu Shengfu, Xing Shule, et al. Effect of Mo and Ni contents on microstructure and properties of deposited metal prepared by martensitic stainless hard-facing flux-cored wire[J]. Materials for Mechanical Engineering, 2013, 37(9): 29-32.
[20]李水清, 陈亮, 丁毅, 等. 镍含量对等离子喷涂Ni-Cr₂O₃复合涂层耐蚀性能的影响[J]. 机械工程材料, 2012, 36(10): 54-57.
Li Shuiqing, Chen Liang, Ding Yi, et al. Effect of nickel content on corrosion resistance of Ni-Cr₂O₃ composite coatings prepared by plasma spraying process[J]. Materials for Mechanical Engineering, 2012, 36(10): 54-57.