横向磁通感应加热激励参数对带材温度的影响及加热器优化

doi:10.13251/j.issn.0254-6051.2021.05.014

金属热处理 ›› 2021, Vol. 46 ›› Issue (5): 87-94.DOI: 10.13251/j.issn.0254-6051.2021.05.014

横向磁通感应加热激励参数对带材温度的影响及加热器优化

闫朝辉^1,2, 汪友华^1,2, 刘成成^1,2, 武仕朴^1,2

1.河北工业大学省部共建电工装备可靠性与智能化国家重点实验室, 天津 300132;
2.河北工业大学河北省电磁场与电器可靠性重点实验室, 天津 300132

收稿日期:2020-10-23 出版日期:2021-05-25 发布日期:2021-07-21
通讯作者: 汪友华,教授,E-mail:wangyi@hebut.edu.cn
作者简介:闫朝辉(1994—),男,硕士研究生,主要研究方向为横向磁通感应加热,E-mail:120752975@qq.com。
基金资助:
国家自然科学基金(50477016)

Influence of transverse flux induction heating excitation parameters on steel strip temperature and heater optimization

Yan Chaohui^1,2, Wang Youhua^1,2, Liu Chengcheng^1,2, Wu Shipu^1,2

1. State Key Laboratory of Reliability and Intelligence of Electrical Equipment, Hebei University of Technology, Tianjin 300132, China;
2. Key Laboratory of Electromagnetic Field and Electrical Apparatus Reliability of Hebei Province, Hebei University of Technology, Tianjin 300132, China

Received:2020-10-23 Online:2021-05-25 Published:2021-07-21

摘要/Abstract

摘要： 在考虑带材物理性能参数随温度变化的前提下,基于横向磁通感应加热耦合场的迭代计算,分析了不同激磁电流、电流频率和带材运动速度对钢带材温度分布的影响。对感应加热器模型进行了优化,改变加热器与带材之间气隙分布,设计了4种感应加热器模型,分析了在不同加热器模型下带材的平均温度和温度均匀性。对比了45钢和35CrMnSiA钢在原始加热器模型与改进后最佳加热器模型下的平均温度与温度均匀性。结果表明:优化后的感应加热器模型使带材表面温度分布更加均匀,平均温度更高。

关键词: 横向磁通感应加热, 耦合场迭代计算, 加热器优化, 45钢, 35CrMnSiA钢

Abstract: Under the premise of considering variation of the strip physical property parameters with temperature, the influence of different excitation current, current frequency and strip movement rate on steel strip temperature distribution was analyzed based on the iterative calculation of transverse flux induction heating coupling field. By changing the air gap distribution between the heater and the strip, the original induction heater model was optimized and other four induction heater models were designed, and the average temperature and temperature uniformity of the strips under different heater models were analyzed. The average temperature and temperature uniformity of the 45 steel and 35CrMnSiA steel under the original heater model and the improved optimal heater model were compared. The results show that the optimized induction heater model makes the surface temperature distribution of the strips more uniform and the average temperature higher.

Key words: transverse flux induction heating, coupled field iterative calculation, heater optimization, 45 steel, 35CrMnSiA steel

中图分类号:

TG161

闫朝辉, 汪友华, 刘成成, 武仕朴. 横向磁通感应加热激励参数对带材温度的影响及加热器优化[J]. 金属热处理, 2021, 46(5): 87-94.

Yan Chaohui, Wang Youhua, Liu Chengcheng, Wu Shipu. Influence of transverse flux induction heating excitation parameters on steel strip temperature and heater optimization[J]. Heat Treatment of Metals, 2021, 46(5): 87-94.

参考文献

[1]汤忠义, 梁合意, 徐友良. 金属材料与热处理[M]. 北京: 北京理工大学出版社, 2011.
[2]俞勇祥, 陈辉明. 感应加热电源的发展[J]. 金属热处理, 2000, 25(8): 28-31.
Yu Yongxiang, Chen Huiming. Development of induction heating power supply[J]. Heat Treatment of Metals, 2000, 25(8): 28-31.
[3]沈庆通. 感应加热技术的发展与思考[J]. 热处理, 2010, 25(5): 1-8.
Shen Qingtong. Development of induction heating and related consideration[J]. Heat Treatment, 2010, 25(5): 1-8.
[4]Li Feng, Li Xuekun, Qin Xiaofeng, et al. Study on the plane induction heating process strengthened by magnetic flux concentrator based on response surface methodology[J]. Journal of Mechanical Science and Technology, 2018, 32(5): 2347-2356.
[5]Lope I, Acero J, Carretero C. Analysis and optimization of the efficiency of induction heating applications with Litz-wire planar and solenoidal coils[J]. IEEE Transactions on Power Electronics, 2016, 31(7): 5089-5101.
[6]杨晓光, 汪友华. 横向磁通感应加热装置中线圈形状对涡流及温度分布的影响[J]. 金属热处理, 2003, 28(7): 49-54.
Yang Xiaoguang, Wang Youhua. The effect of coil geometry on the distributions of eddy current and temperature in transverse flux induction heating equipment[J]. Heat Treatment of Metals, 2003, 28(7): 49-54.
[7]杨晓光, 汪友华. 连续运动薄板横向磁通感应加热耦合场分析新方法[J]. 金属热处理, 2004, 29(4): 53-57.
Yang Xiaoguang, Wang Youhua. New method for coupled field analysis in transverse flux induction heating of continuously moving sheet[J]. Heat Treatment of Metals, 2004, 29(4): 53-57.
[8]孙于. 横向磁通感应加热器优化与耦合分析方法研究[D]. 天津: 河北工业大学, 2014.
Sun Yu. Research on optimal design of transverse flux induction heater and the coupled field analysis method[D]. Tianjin: Hebei University of Technology, 2014.
[9]汪友华, 吴建成, 刘成成, 等. 横向磁通连续感应加热过程中带材涡流场和温度场的仿真分析[J]. 金属热处理, 2019, 44(1): 229-234.
Wang Youhua, Wu Jiancheng, Liu Chengcheng, et al. Simulation and analysis of eddy current field and temperature field of strips during transverse flux continuous induction heating[J]. Heat Treatment of Metals, 2019, 44(1): 229-234.
[10]赵涛, 张浩, 王子兵. C型边部感应加热器磁-热耦合数值模拟[J]. 金属热处理, 2019, 44(7): 202-206.
Zhao Tao, Zhang Hao, Wang Zibing. Numerical simulation of electromagnetic-thermal couple field about C-type edge induction heater[J]. Heat Treatment of Metals, 2019, 44(7): 202-206.
[11]Wu J C, Wang S P, Wang Y H, et al. Sensitivity analysis of design parameters in transverse flux induction heating device[J]. IEEE Transactions on Applied Superconductivity, 2020, 30(4): 0600406.
[12]汪友华, 郭春福, 陈龙, 等. 横向磁通感应加热带材温度场的计算分析[J]. 金属热处理, 2017, 42(11): 178-182.
Wang Youhua, Guo Chunfu, Chen Long, et al. Calculation and analysis of steel strip with transverse flux induction heating[J]. Heat Treatment of Metals, 2017, 42(11): 178-182.

横向磁通感应加热激励参数对带材温度的影响及加热器优化

Influence of transverse flux induction heating excitation parameters on steel strip temperature and heater optimization

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 10

编辑推荐

Metrics

本文评价

[1]	梁怀南, 刘志奇, 陈东良, 宋建丽, 林乃明. 压印模具表面织构电火花成形工艺参数的分析[J]. 金属热处理, 2022, 47(3): 20-27.
[2]	张展展, 宁家庆, 左玲立, 廖海洋. 工艺参数对WC颗粒增强表层复合材料与钢基界面组织的影响[J]. 金属热处理, 2021, 46(11): 131-136.
[3]	张馨月, 杨明维, 冯运莉, 曹阔, 李杰. 退火时间对伪共析45钢温轧后组织与性能的影响[J]. 金属热处理, 2020, 45(4): 132-136.
[4]	刘环，揭晓华，张艳梅，罗松，卢国辉. 45钢表面微纳米多尺度结构制备及抗硫化粘污性能研究[J]. 金属热处理, 2017, 42(4): 159-162.
[5]	王长健. 45钢锥套淬火裂纹失效分析[J]. 金属热处理, 2017, 42(4): 204-207.
[6]	蒋鹏1，张璐莹1，方江涛2. 基于声发射的马氏体相变动力学特性研究[J]. 金属热处理, 2015, 40(8): 55-58.
[7]	王辉，陈晓龙. 45钢表面激光合金化原位生成TiN陶瓷相的组织及性能[J]. 金属热处理, 2015, 40(11): 72-75.
[8]	王啸, 吴从跃, 孙梦龙, 谢春生. QPQ处理对45钢组织与性能的影响[J]. 金属热处理, 2014, 39(8): 92-95.
[9]	原卓浩, 王福明韦士来叶高旗. 含Cr低合金结构钢焊接粗晶热影响区组织与冲击性能[J]. 金属热处理, 2014, 39(6): 1-4.
[10]	陈虎城, 魏德强, 王荣, 史绍远. 45钢表面电子束相变硬化过程中组织转变数值模拟[J]. 金属热处理, 2014, 39(6): 130-135.