敏化温度对高碳奥氏体不锈钢析出行为及力学性能的影响

doi:10.13251/j.issn.0254-6051.2022.12.020

金属热处理 ›› 2022, Vol. 47 ›› Issue (12): 115-119.DOI: 10.13251/j.issn.0254-6051.2022.12.020

敏化温度对高碳奥氏体不锈钢析出行为及力学性能的影响

邢梦楠^1,2, 张海明³, 隋松言², 胡昕明^1,2, 欧阳鑫^1,2, 王储^1,2, 贾春堂^1,2, 刘晨希^1,2

1.海洋装备用金属材料及其应用国家重点实验室, 辽宁鞍山 114009;
2.鞍钢股份有限公司, 辽宁鞍山 114009;
3.鞍钢绿色资源科技有限公司, 辽宁鞍山 114021

收稿日期:2022-06-26 修回日期:2022-10-09 出版日期:2022-12-25 发布日期:2023-01-05
作者简介:邢梦楠(1992—),女,工程师,硕士,主要研究方向为中厚板产品成形与工艺,E-mail:847867099@qq.com

Effect of sensitization temperature on precipitation behavior and mechanical properties of high carbon austenitic stainless steel

Xing Mengnan^1,2, Zhang Haiming³, Sui Songyan², Hu Xinming^1,2, Ouyang Xin^1,2, Wang Chu^1,2, Jia Chuntang^1,2, Liu Chenxi^1,2

1. State Key Laboratory of Metal Material for Marine Equipment and Application, Anshan Liaoning 114009, China;
2. Angang Steel Company Limited, Anshan Liaoning 114009, China;
3. Ansteel Green Resources Technology Company Limited, Anshan Liaoning 114021, China

Received:2022-06-26 Revised:2022-10-09 Online:2022-12-25 Published:2023-01-05

摘要/Abstract

摘要： 采用光学显微镜、扫描电镜、能谱仪、透射电镜等,研究敏化温度对高碳奥氏体不锈钢析出相数量、形态及分布情况的影响,采用拉伸试验机、冲击试验机和布氏硬度仪,分析不同敏化温度下析出相对试验钢力学性能的影响。结果表明,不同敏化温度处理后试样的显微组织均为奥氏体;但随着敏化温度的升高,奥氏体晶界处富Cr碳化物析出增多,以颗粒状和条状形态存在,晶界处析出相尺寸在100~400 nm之间。经650 ℃敏化2 h后试样的强韧性匹配良好,综合力学性能较为优异。

关键词: 敏化处理, 高碳奥氏体不锈钢, 析出相, 力学性能

Abstract: Effect of sensitization temperature on quantity, morphology and distribution of precipitates in a high carbon austenitic stainless steel was studied by means of metallographic microscope, scanning electron microscope, energy dispersive spectrometer and transmission electron microscope. The effect of precipitate on mechanical properties of the tested steel at different sensitization temperatures was analyzed by means of tensile testing machine, impact testing machine and Brinell hardness tester. The results show that microstructure of the specimens sensitized at different temperatures is austenite, while with the increase of sensitization temperature, the precipitation of Cr-rich carbides on the austenite grain boundaries increases and exists in granular and strip forms, and the size of precipitates on the grain boundaries is in the range of 100-400 nm. After sensitizing treatment at 650 ℃ for 2 h, the strength and toughness of the specimen match well, and the comprehensive mechanical properties are excellent.

Key words: sensitization treatment, high carbon austenitic stainless steel, precipitates, mechanical properties

中图分类号:

TG506.7⁺1

邢梦楠, 张海明, 隋松言, 胡昕明, 欧阳鑫, 王储, 贾春堂, 刘晨希. 敏化温度对高碳奥氏体不锈钢析出行为及力学性能的影响[J]. 金属热处理, 2022, 47(12): 115-119.

Xing Mengnan, Zhang Haiming, Sui Songyan, Hu Xinming, Ouyang Xin, Wang Chu, Jia Chuntang, Liu Chenxi. Effect of sensitization temperature on precipitation behavior and mechanical properties of high carbon austenitic stainless steel[J]. Heat Treatment of Metals, 2022, 47(12): 115-119.

参考文献

[1]Msuyama F. History of power plants and progress in heat resistant steels[J]. ISIJ International, 2001, 41(6): 612-625.
[2]Bendick W, Gabrel J, Hahn B, et al. New low alloy heat resistant ferritic steels T/P23 and T/P24 for power plant application [J]. International Journal of Pressure Vessels and Piping, 2007, 84(1/2): 13-20.
[3]Ehlers J, Young D J, Smaardijk E J, et al. Enhanced oxidation of the 9%Cr steel P91 in water vapour containing environments [J]. Corrosion Science, 2006, 48(11): 3428-3454.
[4]程阳. 高温敏化和形变对HR₃C钢析出行为及性能的影响 [D]. 太原: 太原理工大学, 2017.
[5]张慧云, 孟宪明, 郑留伟, 等. 敏化处理对不同状态304奥氏体不锈钢氢脆敏感性的影响 [J]. 金属热处理, 2021, 46(8): 164-169.
Zhang Huiyun, Meng Xianming, Zheng Liuwei, et al. Effect of sensitization on hydrogen embrittlement sensitivity of 304 austenitic stainless steel in different states [J]. Heat Treatment of Metals, 2021, 46(8): 164-169.
[6]易雪庆, 陆永浩, 陈迎锋. 敏化和固溶处理对核级不锈钢Z3CN20-09M相间腐蚀敏感性的影响 [J]. 中国腐蚀与防护学报, 2013, 33(2): 141-147.
Yi Xueqing, Lu Yonghao, Chen Yingfeng. Effects of sensitization and solid-solution treatment on interphase corrosion susceptibility of nuclear grade Z3CN-09M stainless steel [J]. Journal of Chinese Society for Corrosion and Protection, 2013, 33(2): 141-147.
[7]秦丽雁, 宋诗哲, 卢玉琢. 304不锈钢晶间腐蚀过程中的电化学阻抗谱特征 [J]. 中国腐蚀与防护学报, 2007, 27(2): 74-79.
Qin Liyan, Song Shizhe, Lu Yuzhuo. EIS characteristics of 304 stainless steel during intergranular corrosion [J]. Journal of Chinese Society for Corrosion and Protection, 2007, 27(2): 74-79.
[8]荣凡, 康喜范, 郎宇平. 含氮奥氏体不锈钢的敏化行为 [J]. 钢铁, 2005, 40(5): 62-64, 86.
Rong Fan, Kang Xifan, Lang Yuping. Sensitization behavior of nitrogen containing austenitic stainless steel [J]. Iron and Steel, 2005, 40(5): 62-64, 86.
[9]陆世英. 超级不锈钢和高镍耐蚀合金 [M]. 北京: 化学工业出版社, 2012: 493-500.
[10]黄晋华. 316LN不锈钢相析出转变过程及其对耐蚀性能影响的研究 [D]. 南昌: 南昌航空大学, 2015.
[11]王英虎, 郑淮北, 白青青, 等. Mn18Cr18N高氮奥氏体不锈钢的高温力学性能 [J]. 金属热处理, 2022, 47(1): 172-177.
Wang Yinghu, Zheng Huaibei, Bai Qingqing, et al. High temperature mechanical properties of Mn18Cr18N high nitrogen austenitic stainless steel [J]. Heat Treatment of Metals, 2022, 47(1): 172-177.
[12]闫治坤, 陈海涛, 郎宇平, 等. 氮含量及固溶温度对21-6-9奥氏体不锈钢组织和硬度的影响 [J]. 金属热处理, 2021, 46(12): 76-80.
Yan Zhikun, Chen Haitao, Lang Yuping, et al. Effects of nitrogen content and solution treatment temperature on microstructure and hardness of 21-6-9 austenitic stainless steel [J]. Heat Treatment of Metals, 2021, 46(12): 76-80.

[1]	王志文, 杨荣东, 黄元春, 李辉. 时效处理对挤压成型2195铝锂合金组织和力学性能的影响[J]. 金属热处理, 2022, 47(9): 6-11.
[2]	高星, 张宁, 丁燕, 蒋波. 热处理时间对激光选区成形TC4钛合金组织及力学性能的影响[J]. 金属热处理, 2022, 47(9): 12-17.
[3]	夏朋昭, 许莹, 蔡艳青, 赵思坛, 娄冰洁. 微波烧结工艺对Ti-Mg复合材料组织和性能的影响[J]. 金属热处理, 2022, 47(9): 18-26.
[4]	李磊, 朱旭军, 张丽, 田福政. 喷丸直径对GH4169合金性能和损伤演化的影响[J]. 金属热处理, 2022, 47(9): 47-53.
[5]	张浩泽, 王隽生, 宫鹏辉, 詹海艺, 王凯. 热处理对EB铸锭直接轧制TC4合金板材组织和力学性能的影响[J]. 金属热处理, 2022, 47(9): 71-78.
[6]	钟立伟, 冯朝辉, 高文理, 陈军洲, 陆政. 多轴锻造与T852热处理对Al-Cu-Li合金组织及力学性能的影响[J]. 金属热处理, 2022, 47(9): 79-86.
[7]	肖结良, 孙浩, 李飞, 胡平, 陈旌钢, 江兆峰. 球墨铸铁行走轮的低温正火工艺[J]. 金属热处理, 2022, 47(9): 98-102.
[8]	温方明, 郝晓博, 曹恒, 张强, 李渤渤, 刘茵琪. 热处理工艺对N06600合金热轧板组织与性能的影响[J]. 金属热处理, 2022, 47(9): 113-118.
[9]	艾兵权, 邝霜, 田秀刚, 杨峰, 王玉慧, 逯志强, 王朝, 郝雷. 均热温度对不同成分980 MPa级高强钢组织和性能的影响[J]. 金属热处理, 2022, 47(9): 119-124.
[10]	王世凯, 王睿, 康燕, 于志强, 闫志杰. 淬火温度对Cr5MoVNi钢组织和性能的影响[J]. 金属热处理, 2022, 47(9): 125-129.
[11]	熊维亮, 梁文, 吴腾, 梁亮, 吴浩鸿. 控冷工艺对热轧双相钢组织与性能的影响[J]. 金属热处理, 2022, 47(9): 130-133.
[12]	张玉成, 贾浩梅. 固溶处理对Incoloy825合金钢管组织和性能的影响[J]. 金属热处理, 2022, 47(9): 134-139.
[13]	范朝, 程宗辉, 张志强. 激光热输入对激光增材修复1Cr17Ni2不锈钢组织与力学性能的影响[J]. 金属热处理, 2022, 47(9): 140-145.
[14]	姜一鸣, 屈华鹏, 郎宇平, 冯翰秋, 陈海涛, 李向明. 高钼无磁钢等温变形脆化现象及其机理[J]. 金属热处理, 2022, 47(9): 158-163.
[15]	熊书俊, 万佳, 陈金水, 郭诚君, 肖翔鹏. 微合金化Cu-Ni-Sn-P合金的组织和性能[J]. 金属热处理, 2022, 47(9): 164-170.

敏化温度对高碳奥氏体不锈钢析出行为及力学性能的影响

Effect of sensitization temperature on precipitation behavior and mechanical properties of high carbon austenitic stainless steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价