C含量对冷轧Fe-6Mn-1Al中锰钢组织与性能的影响

doi:10.13251/j.issn.0254-6051.2022.02.007

金属热处理 ›› 2022, Vol. 47 ›› Issue (2): 35-40.DOI: 10.13251/j.issn.0254-6051.2022.02.007

C含量对冷轧Fe-6Mn-1Al中锰钢组织与性能的影响

赵彦乐^1,2, 邹宇明^1,2, 丁桦^1,2

1.东北大学材料科学与工程学院, 辽宁沈阳 110819;
2.东北大学辽宁省轻量化用关键金属结构材料重点实验室, 辽宁沈阳 110819

收稿日期:2021-09-26 修回日期:2021-12-02 出版日期:2022-02-25 发布日期:2022-04-01
通讯作者: 丁桦,教授,博士生导师,E-mail:hding@263.net
作者简介:赵彦乐(1993—),女,硕士,主要研究方向为中锰钢组织性能,E-mail:1573537988@qq.com。
基金资助:
国家自然科学基金(U1760205)

Effect of C content on microstructure and mechanical properties of cold-rolled Fe-6Mn-1Al medium manganese steel

Zhao Yanle^1,2, Zou Yuming^1,2, Ding Hua^1,2

1. School of Materials Science and Engineering, Northeastern University, Shenyang Liaoning 110819, China;
2. Key Laboratory of Lightweight Structural Materials in Liaoning Province, Northeastern University, Shenyang Liaoning 110819, China

Received:2021-09-26 Revised:2021-12-02 Online:2022-02-25 Published:2022-04-01

摘要/Abstract

摘要： 研究了C含量(质量分数)分别为0.06%、0.15%和0.30%的冷轧中锰钢Fe-6Mn-1Al退火后的组织及室温拉伸后的力学性能变化规律。结果表明,不同C含量的试验钢经660 ℃退火后的组织均为铁素体+奥氏体的双相组织。随着C含量的增加,试验钢中奥氏体的体积分数由19.34%增加到38.70%,且C含量的增加引起了配分到奥氏体中的C、Mn含量的增加,使奥氏体的稳定性得到了提升。C含量较高的试验钢变形过程中的TRIP效应更显著,使试验钢的加工硬化能力得到了提高,获得更好的综合力学性能。C含量从0.06%增加至0.30%,试验钢的强塑积由28.0 GPa·%增加到51.4 GPa·%。

关键词: C含量, 冷轧中锰钢Fe-6Mn-1Al, 奥氏体稳定性, TRIP效应

Abstract: Annealed microstructure of cold-rolled medium manganese Fe-6Mn-1Al steel with C content of 0.06%, 0.15% and 0.30%(mass fraction), and the mechanical properties after tensile testing at room temperature were studied. The results show that the microstructure of annealed tested steel with different C contents is composed of ferrite+austenite after annealing at 660 ℃. With the increase of C content, the volume fraction of austenite in the tested steel increases from 19.34% to 38.70%, and the increase of C content leads to the increase of partitioning of C and Mn to austenite, which improves the stability of austenite. The TRIP effect in the deformation process of the tested steel with higher C content is more significant, which improves the work hardening ability of the tested steel and obtains better comprehensive mechanical properties. The product of strength and elongation of the tested steel raises from 28.0 GPa·% to 51.4 GPa·% as the C content increases from 0.06% to 0.30%.

Key words: C content, cold-rolled Fe-6Mn-1Al medium manganese steel, austenite stability, TRIP effect

中图分类号:

TG142.1

赵彦乐, 邹宇明, 丁桦. C含量对冷轧Fe-6Mn-1Al中锰钢组织与性能的影响[J]. 金属热处理, 2022, 47(2): 35-40.

Zhao Yanle, Zou Yuming, Ding Hua. Effect of C content on microstructure and mechanical properties of cold-rolled Fe-6Mn-1Al medium manganese steel[J]. Heat Treatment of Metals, 2022, 47(2): 35-40.

参考文献

[1]刘春全, 彭其春, 邓明明, 等. 第3代汽车用Mn-Al系中锰钢的研究现状[J]. 钢铁研究学报, 2017, 29(6): 431-432.
Liu Chunquan, Peng Qichun, Deng Mingming, et al. Research situation of Mn-Al medium manganese steel for 3^rd generation automobile sheet[J]. Journal of Iron and Steel Research, 2017, 29(6): 431-432.
[2]Arlazarov A, Goune M, Bouaziz O, et al. Evolution of microstructure and mechanical properties of medium Mn steels during double annealing[J]. Materials Science and Engineering A, 2012, 542: 31-39.
[3]李楠, 时捷, 陈为亮, 等. 碳含量对冷轧中锰钢双相区退火组织和力学性能的影响[J]. 热加工工艺, 2012, 41(2): 5-8.
Li Nan, Shi Jie, Chen Weiliang, et al. Effect of carbon content on microstructure and mechanical properties of cold-rolled medium manganese steel[J]. Hot Working Technology, 2012, 41(2): 5-8.
[4]尹鸿祥, 赵爱民, 赵征志, 等. Mn含量对低碳中锰TRIP钢组织性能的影响[J]. 材料科学与工艺, 2014, 22(3): 11-14.
Yin Hongxiang, Zhao Aimin, Zhao Zhengzhi, et al. Effect of Mn content on microstructure and mechanical properties of a low carbon medium-manganese TRIP steel[J]. Materials Science and Technology, 2014, 22(3): 11-14.
[5]Cai Z H, Ding H, Xue X, et al. Significance of control of austenite stability and three-stage work-hardening behavior of an ultrahigh strength-high ductility combination transformation induced plasticity steel[J]. Scripta Materialia, 2013, 68(11): 865-868.
[6]Shi J, Sun X J, Wang M Q, et al. Enhanced work-hardening behavior and mechanical properties in ultra fine-grained steels with large-fractioned metastable austenite[J]. Scripta Materialia, 2010, 63(8): 815-818.
[7]宋丽娜, 兰鹏, 刘春秀, 等. 第3代汽车用中锰钢的研究现状[J]. 钢铁研究学报, 2015, 27(7): 1-8.
Song Lina, Lan Peng, Liu Chunxiu, et al. Research of the third generation medium manganese steel[J]. Journal of Iron and Steel Research, 2015, 27(7): 1-8.
[8]Sugimoto K, Kobayashi M, Hashimoto S I. Ductility and strain induced transformation in a high-strength transformation-induced plasticity aided dual-phase steel[J]. Metallurgical and Materials Transactions A, 1992, 23(11): 3085-3091.
[9]王晓东. TRIP 钢微结构—性能的表征与设计[D]. 上海: 上海交通大学, 2006.
Wang Xiaodong. Characterization and design of microstructures vs properties for TRIP steel[D]. Shanghai: Shanghai Jiao Tong University, 2006.
[10]李志超. 中锰高强塑性钢组织性能及奥氏体稳定性研究[D]. 沈阳: 东北大学, 2017.
Li Zhichao. Research on microstructures, mechanical properties and austenite stability in medium Mn content steels with high strength and ductility[D]. Shenyang: Northeast University, 2017.
[11]Li J J, Song R B, Li X, et al. Coupling nano-carbide strengthening with transformation induced plasticity effect to achieve over 1.5 GPa strength with 30% ductility in cold-rolled medium-Mn steel[J]. Vacuum, 2019, 167: 223-226.
[12]Dijk N H, Butt A M, Zhao L, et al. Thermal stability of retained austenite in TRIP steels studied by synchrotron X-ray diffraction during cooling[J]. Acta Materialia, 2005, 53(20): 5439-5447.
[13]米俊龙, 贾涓, 李建, 等. Mn含量对中锰钢Q&P工艺组织及性能的影响[J]. 材料热处理学报, 2019, 40(12): 106-110.
Mi Junlong, Jia Juan, Li Jian, et al. Effect of Mn content on microstructure and properties of medium manganese steel treated by Q&P process[J]. Transactions of Materials and Heat Treatment, 2019, 40(12): 106-110.
[14]Cao W Q, Wang C, Shi J, et al. Microstructure and mechanical properties of Fe-0.2C-5Mn steel processed by ART annealing[J]. Materials Science and Engineering A, 2011, 528(22): 6661-6666.
[15]Sherif M Y, Garcia Mateo C, Sourmail T, et al. Stability of retained austenite in TRIP-assisted steels[J]. Materials Science and Technology, 2004, 20(3): 319-321.
[16]Chen J, Lü M Y, Liu Z Y, et al. Influence of heat treatments on the microstructural evolution and resultant mechanical properties in a low carbon medium Mn heavy steel plate[J]. Metallurgical & Materials Transactions A, 2016, 47(5): 2300-2312.
[17]Hajyakbary F, Sietsma J, Petrov R H, et al. A quantitative investigation of the effect of Mn segregation on microstructural properties of quenching and partitioning steels[J]. Scripta Materialia, 2017, 137: 27-30.
[18]韦习成, 李麟, 符仁钰. TRIP 钢显微组织与性能关系的评述[J]. 钢铁研究学报, 2001, 13(5): 71-76.
Wei Xicheng, Li Lin, Fu Renyu. Review on relation between microstructures and properties of TRIP steel[J]. Journal of Iron and Steel Research, 2001, 13(5): 71-76.

C含量对冷轧Fe-6Mn-1Al中锰钢组织与性能的影响

Effect of C content on microstructure and mechanical properties of cold-rolled Fe-6Mn-1Al medium manganese steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 4

编辑推荐

Metrics

本文评价

[1]	刘韬, 吴红艳, 高秀华, 秦岽烊, 杜林秀. 临界区回火温度对Fe-4Mn-1.2Cr-0.3Cu-0.6Ni中锰钢微观组织和力学性能的影响[J]. 金属热处理, 2022, 47(2): 91-98.
[2]	齐祥羽, 严玲, 李广龙, 李文斌, 杜林秀. 逆转变奥氏体稳定性对中锰钢强韧性的影响[J]. 金属热处理, 2021, 46(9): 205-210.
[3]	潘红波1,2，王文芳3，潘　烁1,2，刘永刚4，詹　华4，肖洋洋4，冷德平4. 临界退火温度对冷轧0.11C-7.05Mn钢组织性能的影响[J]. 金属热处理, 2019, 44(1): 30-34.
[4]	霍颜秋, 张梦贤, 王海波, 蔡培阳. 低碳20Mn2SiVB钢贝氏体相变及其TRIP效应[J]. 金属热处理, 2014, 39(10): 72-75.