硅含量与淬火温度对Q&P钢组织及性能的影响

doi:10.13251/j.issn.0254-6051.2022.03.025

金属热处理 ›› 2022, Vol. 47 ›› Issue (3): 130-135.DOI: 10.13251/j.issn.0254-6051.2022.03.025

硅含量与淬火温度对Q&P钢组织及性能的影响

史娜^1,2,3, 刘伟明^1,2, 刘永刚³, 詹华³, 崔磊³, 潘红波^1,2

1.安徽工业大学冶金减排与资源综合利用教育部重点实验室, 安徽马鞍山 243002;
2.安徽工业大学冶金工程与资源综合利用安徽省重点实验室, 安徽马鞍山 243002;
3.马鞍山钢铁股份有限公司技术中心, 安徽马鞍山 243003

收稿日期:2021-11-14 修回日期:2021-01-27 出版日期:2022-03-25 发布日期:2022-04-22
通讯作者: 刘伟明,讲师,博士,E-mail:417475878@qq.com
作者简介:史娜(1996—),硕士研究生,主要研究方向为汽车先进高强钢组织性能,E-mail:1694591151@qq.com。
基金资助:
国家自然科学基金(U1860105,51774006);安徽省重大专项(18030901085)

Effects of Si content and quenching temperature on microstructure and properties of Q&P steel

Shi Na^1,2,3, Liu Weiming^1,2, Liu Yonggang³, Zhan Hua³, Cui Lei³, Pan Hongbo^1,2

1. Key Laboratory of Metallurgical Emission Reduction and Resources Recycling of Ministry of Education, Anhui University of Technology, Ma'anshan Anhui 243002, China;
2. Anhui Province Key Laboratory of Metallurgical Engineering and Resources Recycling, Anhui University of Technology, Ma'anshan Anhui 243002, China;
3. Technology Center, Ma'anshan Iron and Steel Company, Ma'anshan Anhui 243003, China

Received:2021-11-14 Revised:2021-01-27 Online:2022-03-25 Published:2022-04-22

摘要/Abstract

摘要： 采用盐浴对两种硅含量不同的试验钢进行了淬火配分处理,并用金相显微镜、扫描电镜与拉伸试验机对不同淬火温度下试验钢组织及性能的转变规律展开了研究。结果表明,试验钢的显微组织由铁素体、马氏体、残留奥氏体与贝氏体组成;硅含量增加,有利于试验钢中残留奥氏体体积分数提高,抗拉强度和屈服强度显著提高,伸长率降低,强度随淬火温度变化的幅度减小;经260 ℃淬火、360 ℃配分后,2.13%(质量分数)Si钢在拥有高强度的同时保持了较好的伸长率,其抗拉强度为958.66 MPa,屈服强度为458.99 MPa,伸长率为15.35%,强塑积为14.66 GPa·%,综合力学性能最佳。

关键词: 淬火配分, 硅含量, 淬火温度, 强塑积

Abstract: Two kinds of tested steels with different silicon contents were quenched and partitioned by using salt bath, and microstructure and properties of the tested steels quenched at different temperatures were investigated by means of metallographic microscope, scanning electron microscope and tensile testing machine. The results indicate that microstructure of the tested steels is composed of ferrite, martensite, retained austenite and bainite. With the increase of silicon content, the volume fraction of retained austenite increases marginally, the tensile strength and yield strength increase significantly, and the elongation decreases. In addition, the strength fluctuates slightly with quenching temperature. After quenching at 260 ℃ and partitioning at 360 ℃, the tested steel with 2.13%(mass fraction) Si obtains high strength and good elongation simultaneously, the tensile strength is 958.66 MPa, the yield strength is 458.99 MPa, the elongation and product of strength and elongation reach 15.35 % and 14.66 GPa·%, respectively, therefore, the comprehensive mechanical properties are optimum.

Key words: quenching and partitioning, silicon content, quenching temperature, product of strength and elongation

中图分类号:

史娜, 刘伟明, 刘永刚, 詹华, 崔磊, 潘红波. 硅含量与淬火温度对Q&P钢组织及性能的影响[J]. 金属热处理, 2022, 47(3): 130-135.

Shi Na, Liu Weiming, Liu Yonggang, Zhan Hua, Cui Lei, Pan Hongbo. Effects of Si content and quenching temperature on microstructure and properties of Q&P steel[J]. Heat Treatment of Metals, 2022, 47(3): 130-135.

参考文献

[1]Speer J, Matlock D K, Cooman B C D, et al. Carbon partitioning into austenite after martensite transformation[J]. Acta Materialia, 2003, 51(9): 2611-2622.
[2]Speer J G, Moor E D, Findley K O, et al. Analysis of microstructure evolution in quenching and partitioning automotive sheet steel[J]. Metallurgical & Materials Transactions A, 2011, 42(12): 3591-3601.
[3]Bhargava M, Chakrabarty S, Barnwal V K, et al. Effect of microstructure evolution during plastic deformation on the formability of transformation induced plasticity and quenched & partitioned AHSS[J]. Materials & Design, 2018, 152: 65-77.
[4]田亚强, 黎旺, 郑小平, 等. 合金元素在淬火配分钢中的应用研究进展[J]. 材料导报, 2019, 33(7): 1109-1118.
Tian Yaqiang, Li Wang, Zheng Xiaoping, et al. Application of alloy elements in quenching and partitioning steel: An overview[J]. Materials Review, 2019, 33(7): 1109-1118.
[5]Luo Haiwen, Shi Jie, Wang Chang, et al. Experimental and numerical analysis on formation of stable austenite during the intercritical annealing of 5Mn steel[J]. Acta Materialia, 2011, 59(10): 4002-4014.
[6]尹红霞, 李辉, 史春丽, 等. 奥氏体化温度对汽车用QP钢组织性能的影响[J]. 金属热处理, 2017, 42(11): 108-111.
Yin Hongxia, Li Hui, Shi Chunli, et al. Effect of austenitizing temperature on microstructure and mechanical properties of automotive QP steel[J]. Heat Treatment of Metals, 2017, 42(11): 108-111.
[7]王亚婷, 万德成, 冯树明, 等. 淬火温度对中锰QP钢组织和性能的影响[J]. 金属热处理, 2020, 45(5): 172-176.
Wang Yating, Wan Decheng, Feng Shuming, et al. Effect of quenching temperature on microstructure and mechanical properties of medium manganese QP steel[J]. Heat Treatment of Metals, 2020, 45(5): 172-176.
[8]吝章国, 唐荻, 江海涛, 等. 淬火温度对中锰Q&P钢组织与性能的影响[J]. 金属热处理, 2016, 41(10): 123-127.
Lin Zhangguo, Tang Di, Jiang Haitao, et al. Effect of quenching temperature on microstructure and properties of medium-manganese Q&P steel[J]. Heat Treatment of Metals, 2016, 41(10): 123-127.
[9]Wang L J, Cai Q W, Wu H B. Effects of Si on the stability of retained austenite and temper embrittlement of ultrahigh strength steels[J]. International Journal of Minerals, Metallurgy and Materials, 2011, 18(5): 543-550.
[10]Kim B, Sietsma J, Santofimia M J. The role of silicon in carbon partitioning processes in martensite/austenite microstructures[J]. Materials & Design, 2017, 127: 336-345.
[11]Huyghe P, Caruso M, Collet J L, et al. In situ quantitative assessment of the role of silicon during the quenching and partitioning of a 0.2C steel[J]. Metallurgical & Materials Transactions A, 2019, 50(8): 3486-3494.
[12]Chen H, Sybrand V D Z. Predicting the effect of Mo, Ni, and Si on the bainitic stasis[J]. Metallurgical & Materials Transactions A, 2014, 45(8): 3429-3437.
[13]祝志峰, 赵征志, 赵爱民, 等. Si对高强热轧双相钢组织性能的影响[J]. 轧钢, 2011, 28(2): 16-18.
Zhu Zhifeng, Zhao Zhengzhi, Zhao Aimin, et al. Effect of Si on microstructure and properties of high strength hot-rolled dual phase steel[J]. Steel Rolling, 2011, 28(2): 16-18.
[14]王群, 唐荻, 宋勇, 等. DP590钢线膨胀测量中相转变体积分数的分析[J]. 金属热处理, 2013, 38(1): 108-112.
Wang Qun, Tang Di, Song Yong, et al. Analysis of volume fraction during phase transformation process in linear thermal expansion measurement of dual-phase 590 steel[J]. Heat Treatment of Metals, 2013, 38(1): 108-112.
[15]杨海峰, 王利, 冯伟骏, 等. 锰含量和淬火温度对Q&P钢组织和性能的影响[J]. 热加工工艺, 2011, 40(18): 148-152.
Yang Haifeng, Wang Li, Feng Weijun, et al. Influence of Mn content and quenching temperature on microstructure and mechanical properties of Q&P steel[J]. Hot Working Technology, 2011, 40(18): 148-152.

硅含量与淬火温度对Q&P钢组织及性能的影响

Effects of Si content and quenching temperature on microstructure and properties of Q&P steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	付锡彬, 陈子豪, 张可, 赵时雨, 孙新军, 朱正海, 梁小凯, 雍岐龙. 淬火温度对高Ti低合金耐磨钢组织及力学性能的影响[J]. 金属热处理, 2022, 47(4): 122-127.
[2]	刘文彬, 乔龙阳, 潘新宇, 程格, 李爱娜, 裴新军. 淬火温度对刀剪用M390粉末冶金不锈钢组织和性能的影响[J]. 金属热处理, 2022, 47(4): 189-195.
[3]	陈连生, 房宁, 曹仲乾, 杨子旋, 李红斌, 潘红波, 田亚强. 压下率对两相区温轧淬火配分中锰钢组织性能的影响[J]. 金属热处理, 2022, 47(3): 28-33.
[4]	熊金生, 宁静, 苏杰, 姜庆伟. 淬火温度对低钴二次硬化钢组织和性能的影响[J]. 金属热处理, 2022, 47(3): 92-96.
[5]	刘跃, 韩顺, 厉勇, 王春旭, 严晓红, 李建新. 淬火温度对GE1014超高强度钢组织及性能的影响[J]. 金属热处理, 2022, 47(2): 125-129.
[6]	李荣斌, 秦品强, 陈永强, 李珂, 龙文宇. 不同两相区淬火温度对9Ni钢组织与性能的影响[J]. 金属热处理, 2021, 46(7): 18-22.
[7]	梁晓东, 鞠哲, 刘骥, 王晨充, 王旭. 淬火温度对渗碳齿轮钢C64显微组织及力学性能的影响[J]. 金属热处理, 2021, 46(4): 88-94.
[8]	纪显彬, 李照国, 魏海霞, 钱张信. 淬火温度和氮含量对马氏体不锈钢组织和性能的影响[J]. 金属热处理, 2021, 46(3): 130-134.
[9]	曹鑫, 李权, 杨银辉. 热处理工艺对30Cr16Mo1VN钢组织和性能的影响[J]. 金属热处理, 2021, 46(12): 40-45.
[10]	彭思远, 邓想涛, 梁亮, 付天亮, 刘宁, 王昭东. 淬火温度对新型NM450抗腐蚀磨损钢组织和性能的影响[J]. 金属热处理, 2021, 46(12): 223-228.
[11]	王开泰, 许云波, 徐兵, 顾兴利, 王源, 李佳彧, 倪申亚, 龚殿尧. 980 MPa级热浸镀钢的新型淬火配分工艺及组织性能[J]. 金属热处理, 2021, 46(11): 143-146.
[12]	顾顺杰, 吕传涛, 肖旭, 丁磊, 李阳, 陈鹏飞. 淬火温度对低合金耐蚀27CrMo48VNb钢油井管组织的影响[J]. 金属热处理, 2021, 46(11): 178-181.
[13]	袁伍丰, 吴润, 尉文超, 轩阳, 闫永明. 高碳硅锰钢的动态力学性能[J]. 金属热处理, 2020, 45(9): 155-160.
[14]	梁耀, 于晓华, 种晓宇, 苑振涛. 淬火温度对轧辊用高硼铁基合金组织和力学性能的影响[J]. 金属热处理, 2020, 45(8): 86-90.
[15]	梁校, 罗平, 李贤君, 张文良, 谢华生. Q&P工艺对22MnB5钢微观组织及力学性能的影响[J]. 金属热处理, 2020, 45(7): 57-62.