Ni、Fe合金化及时效时间对锰铜基阻尼合金相变行为的影响

doi:10.13251/j.issn.0254-6051.2022.05.001

金属热处理 ›› 2022, Vol. 47 ›› Issue (5): 1-6.DOI: 10.13251/j.issn.0254-6051.2022.05.001

• 材料研究 • 下一篇

Ni、Fe合金化及时效时间对锰铜基阻尼合金相变行为的影响

牛红康, 王迪玮, 田青超

上海大学省部共建高品质特殊钢冶金与制备国家重点实验室, 上海 200444

收稿日期:2021-12-13 修回日期:2022-02-27 出版日期:2022-05-25 发布日期:2022-06-16
通讯作者: 田青超,教授,博士,E-mail: tctian@shu.edu.cn
作者简介:牛红康(1999—),男,硕士研究生,主要研究方向为锰铜基阻尼合金,E-mail: Niuhk@shu.edu.cn。

Effect of alloying of nickel and iron and aging time on phase transformation behaviour of MnCu based damping alloy

Niu Hongkang, Wang Diwei, Tian Qingchao

State Key Laboratory of Advanced Special Steel, Shanghai University, Shanghai 200444, China

Received:2021-12-13 Revised:2022-02-27 Online:2022-05-25 Published:2022-06-16

摘要/Abstract

摘要： 使用真空感应炉制备了Mn-20Cu、Mn-20Cu-5Ni、Mn-20Cu-5Ni-2Fe三种不同成分梯度的合金,利用动态机械分析仪测量了弹性模量及内耗与温度之间的关系,以研究化学成分及时效时间对合金反铁磁转变及马氏体相变的影响。结果表明,合金的相变特征温度和时效时间的平方根正相关,添加的合金元素通过影响调幅分解过程中溶质原子的扩散从而对特征温度发生作用,描述振荡应力和相界面之间耦合强度的l值是反映阻尼合金材料的关键因素之一。

关键词: MnCu基阻尼合金, 相变, 时效处理, 弹性模量

Abstract: Three alloys with different composition gradients of Mn-20Cu, Mn-20Cu-5Ni and Mn-20Cu-5Ni-2Fe were prepared, the relationships between elastic modulus and internal friction versus temperature were measured by using a dynamic mechanical analyzer to investigate the effects of chemical composition and aging time on antiferromagnetic transformation and martensitic transformation of the alloys. The results show that the characteristic phase transformation temperature of the three alloys is positively correlated with the square root of the aging time, the alloying elements act on the characteristic temperature by influencing the diffusion of solute atoms during spinodal decomposition and that the l-value describing the coupling strength between applied oscillating stress and phase interface is one of the key factors reflecting the damping alloy material.

Key words: MnCu based damping alloy, phase transformation, aging treatment, elastic modulus

中图分类号:

TG146

牛红康, 王迪玮, 田青超. Ni、Fe合金化及时效时间对锰铜基阻尼合金相变行为的影响[J]. 金属热处理, 2022, 47(5): 1-6.

Niu Hongkang, Wang Diwei, Tian Qingchao. Effect of alloying of nickel and iron and aging time on phase transformation behaviour of MnCu based damping alloy[J]. Heat Treatment of Metals, 2022, 47(5): 1-6.

参考文献

[1]Tian Q, Yin F, Sakaguchi T, et al. Reverse transformation behavior of a prestrained MnCu alloy[J]. Acta Materialia, 2006, 54(7): 1805-1813.
[2]Bacon G E, Dunmur I W, Smith J H, et al. The antiferromagnetism of manganese copper alloys[J]. Proceedings of the Royal Society A, Mathematical, Physical and Engineering Sciences, 1957, 241: 223-238.
[3]Markova G V. Internal friction during martensitic transformation in high manganese Mn-Cu alloys[J]. Materials Science and Engineering A, 2004, 370(1/2): 473-476.
[4]Cui S S, Shi S, Zhao Z M, et al. Tunable elastic modulus in Mn-based antiferromagnetic shape memory alloys[J]. Materials Research Express, 2016, 3(7): 075701.
[5]彭文屹, 邓华铭, 张骥华. Mn-Ni合金的反铁磁转变与马氏体相变[J]. 金属学报, 2003(11): 1153-1156.
Peng Wenyi, Deng Huaming, Zhang Jihua. Antiferromagnetic transition and martensite transformation in Mn-Ni alloys[J]. Acta Metallurgica Sinica, 2003(11): 1153-1156.
[6]Bidaux J E, Schaller R, Benoit W. Study of the hcp-fcc phase transition in cobalt by acoustic measurements[J]. Acta Metallurgica, 1989, 37(3): 803-811.
[7]Belko V N, Darinsky B M, Postnikov V S, et al. Internal friction during diffusionless phase transformations in Co-Ni alloys[J]. Physics of Metals and Metallography, 1969, 27(1): 140-146.
[8]Zhang J X, Fung P C W, Zeng W G. Dissipation function of the first-order phase transformation in solids via internal-friction measurements[J]. Physical Review B, 1995, 52(1): 268.
[9]Hou S, Qin F, Han J, et al. Strain glass transition in high damping Mn-22Cu-5Ni-2Fe alloy[J]. Progress in Natural Science: Materials International, 2018, 28(5): 614-617.
[10]Jiang Z C, Zhang S B, Tian Q C, et al. Phenomenological representation of mechanical spectroscopy of high damping MnCuNiFe alloy[J]. Materials Science and Technology, 2020, 36(6): 743-749.
[11]王力田, 葛庭燧. MnCu合金马氏体相变和马氏体的内耗[J]. 金属学报, 1988, 24(3): 147-154.
Wang Litian, Ge Tingsui. Internal friction in martensite and martensitic transformation in MnCu alloys[J]. Acta Metallurgica Sinica, 1988, 24(3): 147-154.
[12]Venkateswararao P, Chatterjee D K. Structural studies on the alloying behaviour of γ-Mn and the development of a high damping capacity in Mn-Cu alloys[J]. Journal of Materials Science, 1980, 15(1): 139-148.
[13]Sugimoto K, Mori T, Shiode S. Effect of composition on the internal friction and Young's modulus in γ phase Mn-Cu alloys[J]. Metal Science Journal, 1973, 7(1): 103-108.
[14]胡赓祥, 蔡珣, 戎咏华. 材料科学基础[M]. 上海: 上海交通大学出版社, 2009: 144-153.
[15]郝士明. 材料热力学[M]. 北京: 化学工业出版社, 2003: 48-55.
[16]Thibon I, Guillou A, Gloriant T. Interdiffusion in the fcc phase of Cu-Mn binary alloys[J]. Journal of Phase Equilibria and Diffusion, 2012, 33(4): 303-309.
[17]张金金. γ-MnFe基合金双程形状记忆效应和磁诱发应变机制探索[D]. 上海: 上海交通大学, 2007: 9-13.
[18]Lu F S, Wu B, Zhang J F, et al. Microstructure and damping properties of MnCuNiFeCe alloy[J]. Rare Metals, 2016, 35(8): 615-619.
[19]Tian Q, Yin F, Sakaguchi T, et al. Internal friction behavior of the reverse martensitic transformation in deformed MnCu alloy[J]. Materials Science and Engineering A, 2006, 438: 374-378.
[20]刘军民, 张进修. 共析转变过程中内耗与复模量行为的对比[J]. 金属学报, 1996(8): 758-790.
Liu Junmin, Zhang Jinxiu. Behaviour of complex elastic modulus and internal friction during eutectoid decomposition[J]. Acta Metallurgica Sinica, 1996(8): 758-790.
[21]刘军民. MnCu合金热弹性马氏体相变过程中的非线性内耗行为[J]. 物理学报, 1997(12): 2408-2417.
Liu Junmin. Nonlinear internal friction behavior in MnCu alloy during thermoelastic martensitic transition[J]. Acta Physica Sinica, 1997(12): 2408-2417.

Ni、Fe合金化及时效时间对锰铜基阻尼合金相变行为的影响

Effect of alloying of nickel and iron and aging time on phase transformation behaviour of MnCu based damping alloy

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	谷国超, 李瑞芬, 辛振民, 袁召富, 崔树刚, 许文花, 吕宇鹏. 2507超级双相不锈钢中第二相的析出行为[J]. 金属热处理, 2022, 47(5): 92-97.
[2]	陈东俊, 李广阳, 刘刚. 时效处理对AlSi9Cu3压铸铝合金组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 53-56.
[3]	王云龙, 余伟, 张昳, 史佳新, 李明辉. 奥氏体化温度对贝氏体钢等温转变及力学性能的影响[J]. 金属热处理, 2022, 47(4): 80-85.
[4]	胡静, 陶科, 杨庆松, 李刚, 张德汉. 机械抛光后的时效工艺对0Cr25Al5电热合金拉拔性能的影响[J]. 金属热处理, 2022, 47(4): 171-177.
[5]	杨春苗, 王珊, 王淑慧, 李延珍, 刘文文. RRA过程中预时效时间对7A85铝合金组织性能的影响[J]. 金属热处理, 2022, 47(3): 44-47.
[6]	王英虎, 郑淮北, 白青青, 宋令玺, 姚斌, 王利伟. 无磁钻铤用Cr-Mn-Ni-N系高氮钢平衡凝固相变与析出行为[J]. 金属热处理, 2022, 47(3): 173-180.
[7]	吕金峄, 张义伟, 罗小兵, 袁晓敏. 含铜钢奥氏体连续冷却组织转变特性的原位观察[J]. 金属热处理, 2022, 47(1): 19-24.
[8]	谭皎, 张伯岩, 朱文光, 孙巧艳. 时效温度对Ti-5Al-4Zr-10Mo-3Cr钛合金微观组织及力学性能的影响[J]. 金属热处理, 2022, 47(1): 217-225.
[9]	杜鹏举, 吴迪. 中锰钢中原奥氏体晶粒尺寸对马氏体相变的影响[J]. 金属热处理, 2021, 46(9): 21-27.
[10]	丁轩, 甘玉荣, 蒋爱娟, 李辉, 杨明球. 时效处理对7A55铝合金微观组织和性能的影响[J]. 金属热处理, 2021, 46(9): 120-123.
[11]	高志喆, 程福超, 冯一帆, 孙健, 王永金. 时效时间对低密度超高锰铸钢组织性能的影响[J]. 金属热处理, 2021, 46(8): 115-120.
[12]	韩茜, 李茂扬, 秦国飞, 李旭东, 董超, 张美丽, 代卫丽. 固溶时效处理对8030铝合金导线组织性能的影响[J]. 金属热处理, 2021, 46(8): 125-132.
[13]	张楠, 李岩, 定巍. 0.2C-5Mn-0.5Si-2.5Al中锰钢临界退火后的微观组织及力学性能[J]. 金属热处理, 2021, 46(7): 37-42.
[14]	张梅, 孙国胜, 秦岽烊, 杜林秀. 冷轧304不锈钢的马氏体逆相变及奥氏体再结晶行为[J]. 金属热处理, 2021, 46(7): 51-55.
[15]	张可人, 许晓静, 张洁. 多级固溶时效对7×××系超高强冷挤压铝合金组织性能的影响[J]. 金属热处理, 2021, 46(7): 165-167.