回火温度对40CrMoVNbTi钢组织和性能的影响

doi:10.13251/j.issn.0254-6051.2023.01.034

金属热处理 ›› 2023, Vol. 48 ›› Issue (1): 193-197.DOI: 10.13251/j.issn.0254-6051.2023.01.034

回火温度对40CrMoVNbTi钢组织和性能的影响

孙永真, 程巨强, 赵翛涵

西安工业大学材料与化工学院, 陕西西安 710021

收稿日期:2022-08-16 修回日期:2022-11-17 出版日期:2023-01-25 发布日期:2023-02-03
通讯作者: 程巨强,教授,博士,E-mail:chengjuqiang@163.com
作者简介:孙永真(1997—),男,硕士研究生,主要研究方向为高强度钢铁材料研究与应用,E-mail:2195318475@qq.com。

Effect of tempering temperature on microstructure and properties of 40CrMoVNbTi steel

Sun Yongzhen, Cheng Juqiang, Zhao Xiaohan

College of Materials Science and Chemical Engineering, Xi'an Technological University, Xi'an Shaanxi 710021, China

Received:2022-08-16 Revised:2022-11-17 Online:2023-01-25 Published:2023-02-03

摘要/Abstract

摘要： 采用780 ℃亚温淬火和不同温度回火,探究回火温度对40CrMoVNbTi钢组织和力学性能的影响。对淬火不同温度回火40CrMoVNbTi钢的力学性能变化及显微组织和冲击断口断貌进行观察和分析。结果表明,780 ℃亚温淬火,随回火温度的提高,40CrMoVNbTi钢的强度下降,塑性呈上升趋势,300 ℃回火冲击吸收能量值最低,出现回火脆性。200 ℃回火组织为回火马氏体和残留奥氏体,其抗拉强度为2150 MPa,KV₂为23.8 J;550~600 ℃回火组织为回火索氏体,韧性较好,其抗拉强度为1190~1070 MPa,KV₂为94~123 J,满足AISI 4140钢的力学性能要求,具有较高的冲击性能。

关键词: 40CrMoVNbTi钢, 回火温度, 组织与性能

Abstract: Effect of tempering temperature on microstructure and mechanical properties of 40CrMoVNbTi steel was investigated by means of 780 ℃ subcritical quenching and tempering at different temperatures. The mechanical properties, microstructure and impact fracture of the 40CrMoVNbTi steel tempered at different temperatures were observed and analyzed. The test results show that the strength decreases and the plastic index increases with the increase of tempering temperature, and the impact absorbed energy value tempered at 300 ℃ is the lowest and the temper brittleness occurs. The tensile strength of the 40CrMoVNbTi steel tempered at 200 ℃ is 2150 MPa and KV₂ is 23.8 J. When tempered at 550-600 ℃,the microstructure of the 40CrMoVNbTi steel is tempered sorbite, the tensile strength is 1190-1070 MPa and KV₂ is 94-123 J, and the mechanical properties can meet the requirements of AISI 4140 steel and have a high impact property.

Key words: 40CrMoVNbTi steel, quenching and tempering, tempering temperature, microstructure and properties

中图分类号:

TG142.1

孙永真, 程巨强, 赵翛涵. 回火温度对40CrMoVNbTi钢组织和性能的影响[J]. 金属热处理, 2023, 48(1): 193-197.

Sun Yongzhen, Cheng Juqiang, Zhao Xiaohan. Effect of tempering temperature on microstructure and properties of 40CrMoVNbTi steel[J]. Heat Treatment of Metals, 2023, 48(1): 193-197.

参考文献

[1]杜海明, 费新刚, 张静. 42CrMo锚栓断裂分析[J]. 物理测试, 2020, 38(1): 49-51.
Du Haiming, Fei Xingang, Zhang Jing. Fracture analysis of 42CrMo anchor bolt[J]. Physical Measurement, 2020, 38(1): 49-51.
[2]郭十奇, 柯美武, 陶会丽. 42CrMo 钢双排链轮轴调质工艺改进[J]. 金属热处理, 2011, 36(6): 118-119.
Guo Shiqi, Ke Meiwu, Tao Huili. Improvement of quenching and tempering process of 42CrMo steel double row sprocket shaft[J]. Heat Treatment of Metals, 2011, 36(6): 118-119.
[3]程晔锋, 程巨强, 冯熠婷. 回火温度对高强无碳化物贝氏体钢无缝管组织和性能的影响[J]. 金属热处理, 2020, 45(11): 201-204.
Cheng Yefeng, Cheng Juqiang, Feng Yiting. Effect of tempering temperature on microstructure and properties of high-strength carbide-free bainite seamless pipe[J]. Heat Treatment of Metals, 2020, 45(11): 201-204.
[4]李梦鸽, 程巨强, 尹思博. 不同截面尺寸贝氏体非调质钢的组织和性能[J]. 金属热处理, 2021, 46(8): 65-69.
Li Mengge, Cheng Juqiang, Yin Sibo. Microstructure and properties of bainitic non-quenched and tempered steel with different section size[J]. Heat Treatment of Metals, 2021, 46(8): 65-69.
[5]程晔锋, 程巨强, 齐超. 回火温度对低合金高强度无缝钢管组织和性能的影响[J]. 上海金属, 2021, 43(1): 55-59.
Cheng Yefeng, Cheng Juqiang, Qi Chao. Effect of tempering temperature on microstructure and properties of low alloy high strength seamless steel pipe[J]. Shanghai Metals, 2021, 43(1): 55-59.
[6]薛冰, 陈世洪, 任永胜. 回火热处理对GCr15轴承钢显微组织和力学性能的影响[J]. 山东理工大学学报(自然科学版), 2021, 35(2): 73-76.
Xue Bing, Chen Shihong, Ren Yongsheng. Effect of tempering heat treatment on microstructure and mechanical properties of GCr15 bearing steel[J]. Journal of Shandong University of Technology (Natural Science), 2021, 35(2): 73-76.
[7]杨敏, 崔冕, 李占阳, 等. 回火温度对 42CrMo 钢显微组织及力学性能的影响[J]. 现代冶金, 2019, 47(1): 4-5.
Yang Min, Cui Mian, Li Zhanyang, et al. Effect of Tempering temperature on microstructure and mechanical properties of 42CrMo steel[J]. Modern Metallurgy, 2019, 47(1): 4-5
[8]陈俊丹, 莫文林, 王培, 等. 回火温度对42CrMo钢冲击韧性的影响[J]. 金属学报, 2012, 48(10): 1186-1193.
Chen Jundan, Mo Wenlin, Wang Pei, et al. Influence of tempering temperature on impact toughness of 42CrMo steel[J]. Acta Metallurgica Sinica, 2012, 48(10): 1186-1193.
[9]Behrens B A, Brunotte K, Petersen T, et al. Mechanical and thermal influences on microstructural during process-integrated thermome chanically controlled forging of tempering steel AISI 4140[J]. Materials Basel, 2020, 13(24): 5772.
[10]Mian Muhammad Bilal, Khurram Yaqoob, Mohammad Hammad Zahid, et al. Effect of austempering conditions on the microstructure and mechanical properties of AISI 4340 and AISI 4140 steels[J]. Journal of Materials Research and Technology, 2019, 8(6): 5194-5200.
[11]Abdul Rauf Jamali, Waseem Khan, Ali Dad Chandio, et al. Effect of cryogenic treatment on mechanical properties of AISI 4340 and AISI 4140 steel[J]. Mehran University Research Journal of Engineering and Technology, 2019, 38(3): 755-766.

[1]	元亚莎, 汪雨昌, 王文焱, 石如星, 元莎, 张玉栋. 回火温度对55NiCrMoV7热作模具钢组织和性能的影响[J]. 金属热处理, 2023, 48(1): 133-138.
[2]	李金波, 吴红艳, 高秀华, 陈红卫, 李绍杰, 朱子颖, 杜林秀. 热处理工艺对高铁耐蚀60Si2Mn弹簧钢组织和性能的影响[J]. 金属热处理, 2022, 47(8): 135-140.
[3]	匡成阳, 马煜林, 王辰昱, 何家勇, 鲁坤. 回火温度对耐热钢组织和性能的影响[J]. 金属热处理, 2022, 47(7): 129-133.
[4]	刘丹, 陈杰, 刘文鉴, 周文浩, 罗登, 张青学. 回火温度对Q1100超高强钢组织和性能的影响[J]. 金属热处理, 2022, 47(5): 111-117.
[5]	梁恩溥, 徐乐, 杨勇, 王毛球. 添加Al、Cu对40CrNi3MoV钢组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 17-23.
[6]	王琪, 吴光亮. 回火温度对1100 MPa级高强钢组织与性能的影响[J]. 金属热处理, 2022, 47(4): 146-150.
[7]	庞庆海, 郎庆斌, 何春静, 王九花, 元亚莎. 5Cr2NiMoVSi模具钢的相变规律与力学性能[J]. 金属热处理, 2022, 47(3): 186-190.
[8]	周泽宇, 花福安. 快速加热和短时保温对22MnB5钢组织与性能的影响[J]. 金属热处理, 2022, 47(12): 1-6.
[9]	宁静, 杨鹏, 高齐, 苏杰. 回火温度对30Cr3Si2NiMoWNb钢组织性能的影响[J]. 金属热处理, 2022, 47(11): 95-99.
[10]	车马俊, 周生璇, 杜晓洁, 赵晋斌, 何宜柱, 徐震霖. 回火温度对EH890海洋工程用钢耐蚀性能的影响[J]. 金属热处理, 2022, 47(10): 147-153.
[11]	朱震宇, 吴志方, 吴润. 回火温度对NM500耐磨钢组织和性能的影响[J]. 金属热处理, 2022, 47(10): 154-159.
[12]	陈忠. 加热温度对Al-Si涂层热成形钢组织及性能的影响[J]. 金属热处理, 2022, 47(10): 228-233.
[13]	戴彦璋, 韩顺, 厉勇, 周敏, 王春旭. 回火温度对新一代传动齿轮钢C61组织及性能的影响[J]. 金属热处理, 2022, 47(1): 49-55.
[14]	邓彪, 陈蓬, 王国栋. 回火温度对二次硬化马氏体不锈钢组织和性能的影响[J]. 金属热处理, 2021, 46(9): 65-71.
[15]	黄娟, 黄元春, 申振宇, 李湘粤, 曾渝, 杨庚辰. 终轧温度及退火温度对5052铝合金板材组织及性能的影响[J]. 金属热处理, 2021, 46(9): 79-84.

回火温度对40CrMoVNbTi钢组织和性能的影响

Effect of tempering temperature on microstructure and properties of 40CrMoVNbTi steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价