V对含氮马氏体不锈钢组织和力学性能的影响

doi:10.13251/j.issn.0254-6051.2023.03.039

金属热处理 ›› 2023, Vol. 48 ›› Issue (3): 236-241.DOI: 10.13251/j.issn.0254-6051.2023.03.039

V对含氮马氏体不锈钢组织和力学性能的影响

曹鑫^1,2, 李权², 杨银辉¹

1.昆明理工大学材料科学与工程学院, 云南昆明 650093;
2.钢铁研究总院特殊钢研究所, 北京 100081

收稿日期:2022-10-30 修回日期:2023-02-06 出版日期:2023-03-25 发布日期:2023-04-25
通讯作者: 杨银辉,教授,博士,E-mail:yyhyanr@sina.com。
作者简介:曹鑫(1996—),男,硕士研究生,主要研究方向为金属材料,E-mail:caoxin1113@qq.com。

Effect of vanadium on microstructure and mechanical properties of nitrogen-containing martensitic stainless steel

Cao Xin^1,2, Li Quan², Yang Yinhui¹

1. Faculty of Materials Science and Engineering, Kunming University of Science and Technology, Kunming Yunnan 650093, China;
2. Institute of Special Steel, Central Iron and Steel Research Institute, Beijing 100081, China

Received:2022-10-30 Revised:2023-02-06 Online:2023-03-25 Published:2023-04-25

摘要/Abstract

摘要： 为提升含氮马氏体不锈钢在高温下服役性能,设计了两种试验钢(一种添加0.12%V (质量分数),一种不加V),采用冲击、拉伸试验机、洛氏硬度计、Thermo-Calc软件、OM、SEM、TEM研究了添加微量的V对含氮马氏体不锈钢组织和力学性能的影响。结果表明,在较高温度450~550 ℃下回火,添加0.12%V较不加V的含氮马氏体不锈钢硬度提高了0.6~1.9 HRC,冲击吸收能量提高了1.2~3.8 J。1050 ℃淬火、-73 ℃冷处理、530 ℃回火后,添加0.12%V钢的塑韧性得到较大提升,断裂方式改变为韧-脆混合断裂,原奥氏体晶粒尺寸由16.48 μm减小为11.12 μm,未溶第二相的种类和分布由沿着原奥氏体晶界呈断链状分布的短棒状M₂₃C₆碳化物转变为弥散分布的球状碳化物和碳氮化物。通过细化晶粒和均匀分布的球状碳化物、碳氮化物,使得含氮马氏体不锈钢的强度和塑韧性均得到提升。

关键词: 含氮马氏体不锈钢, 钒, 脆性断裂, 晶粒细化, 性能

Abstract: In order to improve the service performance of nitrogen-containing martensitic stainless steel at high temperature, two tested steels (one with 0.12%V (mass fraction) and one without V) were designed. The effect of adding a trace amount of vanadium on microstructure and mechanical properties of the nitrogen-containing martensitic stainless steel was studied by impact tester, tensile tester, hardness tester, Thermo-Calc software, OM, SEM and TEM. The results show that the hardness of nitrogen bearing martensitic stainless steel with 0.12%V tempered at 450-550 ℃ is 0.6-1.9 HRC higher and the impact absorbed energy is 1.2-3.8 J higher than that without V. After quenching at 1050 ℃, cryogenic treatment at -73 ℃ and tempering at 530 ℃, the plasticity and toughness of the 0.12%V steel are greatly improved, the fracture mode changes to ductile-brittle mixed fracture, and the prior austenite grain size decreases from 16.48 μm to 11.12 μm, the types and distribution of the secondary phases change from the short rod-like coarse carbides distributed as broken chains along the prior austenite grain boundary into dispersively distributed spherical carbides and carbonitrides. Thus the strength and ductility of the nitrogen bearing martensitic stainless steel are all improved by refining grains and uniformly distributing spherical carbides and carbonitrides.

Key words: nitrogen-containing martensitic stainless steel, vanadium, brittle fracture, grain refinement, properties

中图分类号:

TG156

曹鑫, 李权, 杨银辉. V对含氮马氏体不锈钢组织和力学性能的影响[J]. 金属热处理, 2023, 48(3): 236-241.

Cao Xin, Li Quan, Yang Yinhui. Effect of vanadium on microstructure and mechanical properties of nitrogen-containing martensitic stainless steel[J]. Heat Treatment of Metals, 2023, 48(3): 236-241.

参考文献

[1]Hnninen H. Application and performance of high nitrogen steels[C]// 7th International Conference on High Nitrogen Steels, 2004.
[2]李昭昆, 罗志强, 李建新, 等. 高氮马氏体不锈轴承钢的组织与性能[J]. 金属热处理, 2018, 43(5): 15-21.
Li Zhaokun, Luo Zhiqiang, Li Jianxin, et al. Microstructure and mechanical properties of high nitrogen martensite stainless bearing steel[J]. Heat Treatment of Metals, 2018, 43(5): 15-21.
[3]俞峰, 魏果能, 许达. 不锈轴承材料的研究和发展[J]. 钢铁研究学报, 2005, 17(1): 6-9.
Yu Feng, Wei Guoneng, Xu Da. Research and development of stainless bearing material[J]. Journal of Iron and Steel Research, 2005, 17(1): 6-9.
[4]胡正飞, 吴细毛, 张斌, 等. 长期服役的12%Cr马氏体耐热钢中的碳化物及其变化[J]. 动力工程学报, 2010, 30(4): 269-274.
Hu Zhengfeng, Wu Ximao, Zhang Bin, et al. Evolution of carbides in 12%Cr heat-resistant steels after long-term services[J]. Journal of Chinese Society of Power Engineering, 2010, 30(4): 269-274.
[5]Fang W, Zhang C, Gou F, et al. The effect of microalloying elements (vanadium, titanium) additions on the austenite grain growth behavior in medium carbon steel containing nitrogen[J]. Materials Science and Engineering Technology, 2020, 51(2): 230-237.
[6]Wang M J, Wang Y, Sun F. Tempering behavior of a semi-high speed steel containing nitrogen[J]. Materials Science and Engineering A, 2006, 438: 1139-1142.
[7]夏书文, 左鹏鹏, 张永强, 等. 热锻模具开裂失效分析[J]. 金属热处理, 2018, 43(12): 232-237.
Xia Shuwen, Zuo Pengpeng, Zhang Yongqiang, et al. Cracking failure analysis of hot forging die[J]. Heat Treatment of Metals, 2018, 43(12): 232-237.
[8]尹桂全, 黄贞益, 杨才福, 等. 氮含量和TMCP对微合金V-N钢显微组织和力学性能的影响[J]. 金属热处理, 2008, 33(3): 4-8.
Yin Guiquan, Huang Zhenyi, Yang Caifu, et al. Effects of nitrogen content and TMCP on microstructure and mechanical properties of V-N micro-alloying steels[J]. Heat Treatment of Metals, 2008, 33(3): 4-8.
[9]Guo H, Du S, Lei J, et al. Influence of twin carbide structure on friction and wear properties of G95Cr18 stainless bearing steel[J]. Frontiers in Materials, 2019, 6: 162.

[1]	仇晨, 荣莉, 魏午, 王为, 文胜平, 黄晖, 董阳, 王玉刚. 缓慢升温时效处理对Al-Zn-Mg-Er-Zr合金性能的影响[J]. 金属热处理, 2023, 48(3): 8-11.
[2]	邓红玲, 张思雨, 钟辉隆, 李声慈, 齐亮, 陈继强. 固溶处理对稀土改性Al-Zn-Mg-Cu合金组织及性能的影响[J]. 金属热处理, 2023, 48(3): 32-38.
[3]	周金鑫, 麻永林, 刘永珍, 陈重毅, 宫美娜, 邢淑清. 脉冲磁场对Al-6.15Zn-1.41Mg-1.45Cu合金双级时效组织和性能的影响[J]. 金属热处理, 2023, 48(3): 39-44.
[4]	吴秋云, 潘红波, 刘永刚, 詹华, 崔磊. I&Q&P工艺对C-Si-Mn-Nb双相钢显微组织和力学性能的影响[J]. 金属热处理, 2023, 48(3): 45-50.
[5]	宋先和, 刘晓烨, 毕仁贵, 卢立伟, 刘雁峰, 黄熙鸿. 轧制温度和后处理方式对AZ31镁合金显微组织和力学性能的影响[J]. 金属热处理, 2023, 48(3): 62-70.
[6]	代礼斌, 杨章程, 邓雄, 邱仕佳, 郑朝清. 固溶温度对A286合金低温力学性能的影响[J]. 金属热处理, 2023, 48(3): 96-99.
[7]	杨凯, 朱宏伟, 于利民, 郁瑞兴. 时效时间对PH13-8Mo不锈钢组织和力学性能的影响[J]. 金属热处理, 2023, 48(3): 100-103.
[8]	陈治, 李宝奎, 卢金生, 许鸿翔, 张衡. 渗氮处理在重载齿轮上的应用进展[J]. 金属热处理, 2023, 48(3): 104-111.
[9]	闫洪涛, 王永金, 齐海龙, 黄岩, 张科明, 张澣斗, 母镕. 淬火温度对空冷贝氏体-马氏体复相耐磨钢组织性能的影响[J]. 金属热处理, 2023, 48(3): 129-134.
[10]	邓闪闪, 孙永庆, 蒋业华, 刘振宝, 梁剑雄, 王长军. A286合金的高温持久性能[J]. 金属热处理, 2023, 48(3): 179-187.
[11]	常耀东, 齐会萍, 贾燕龙, 李永堂, 武永红. Q345/40Cr钢双金属环件的热处理工艺及组织性能[J]. 金属热处理, 2023, 48(3): 195-202.
[12]	刘全明, 肖俊峰, 龙伟民, 傅莉, 杨海瑛, 高斯峰. Sn改性Ti-Zr-Cu-Ni钎料的微观组织和力学性能[J]. 金属热处理, 2023, 48(3): 209-214.
[13]	岳旭, 张明玉, 同晓乐, 乔恩利, 张起, 杨嘉珞, 叶红川. Ti-6.5Al-3.5Mo-1.5Zr-0.3Si合金中α′相和α″相的组织演变与力学性能[J]. 金属热处理, 2023, 48(3): 215-220.
[14]	孙威威, 剌玲敏, 张静, 梁凤啸, 秦林. TA2钛板掺杂钒离子渗碳层的耐腐蚀性能[J]. 金属热处理, 2023, 48(3): 230-235.
[15]	陈子宏, 薛正良, 刘孟珂, 张翔, 郑顶立, 马国军. 残余元素Sb对X80管线钢力学性能的影响[J]. 金属热处理, 2023, 48(3): 248-253.

V对含氮马氏体不锈钢组织和力学性能的影响

Effect of vanadium on microstructure and mechanical properties of nitrogen-containing martensitic stainless steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价