回火参数对G95Cr18马氏体不锈钢显微组织及力学性能的影响

doi:10.13251/j.issn.0254-6051.2023.07.018

金属热处理 ›› 2023, Vol. 48 ›› Issue (7): 103-110.DOI: 10.13251/j.issn.0254-6051.2023.07.018

回火参数对G95Cr18马氏体不锈钢显微组织及力学性能的影响

刘永宝, 周丽娜, 刘明, 高翔, 石东丹

中国航发哈尔滨轴承有限公司, 黑龙江哈尔滨 150025

收稿日期:2023-02-06 修回日期:2023-05-30 出版日期:2023-07-25 发布日期:2023-09-04
通讯作者: 周丽娜,高级工程师,博士,E-mail:zhoulina626@126.com
作者简介:刘永宝(1984—),男,工程师,硕士,主要研究方向为金属材料热处理,E-mail:liuyb0015@163.com。

Effect of tempering parameters on microstructure and mechanical properties of G95Cr18 martensitic stainless steel

Liu Yongbao, Zhou Lina, Liu Ming, Gao Xiang, Shi Dongdan

AECC Harbin Bearing Co., Ltd., Harbin Heilongjiang 150025, China

Received:2023-02-06 Revised:2023-05-30 Online:2023-07-25 Published:2023-09-04

摘要/Abstract

摘要： 利用光学显微镜(OM)、扫描电镜(SEM)及X射线衍射仪(XRD)研究了回火参数对G95Cr18钢微观组织的影响;同时利用维氏硬度计、电子万能试验机及落锤冲击试验机等研究了不同回火温度及次数对其硬度、拉伸性能及冲击性能的影响。结果表明,随着回火温度的升高,G95Cr18钢残留奥氏体含量呈逐渐减少趋势,由于碳分配效应导致热稳定性增加,回火温度为200 ℃时,残留奥氏体分解量≤3.6%,当回火温度升高至≥400 ℃,残留奥氏体含量可满足＜6%;随着回火温度升高,G95Cr18钢硬度呈现先降低后升高现象,二次硬化温度为400 ℃;随着回火温度的升高,G95Cr18钢的冲击吸收能量呈现先增加后减小的趋势,回火温度为300 ℃时,冲击吸收能量达到最大值,为7.1 J;当回火温度≤300 ℃时,增加回火次数对G95Cr18钢微观组织及强韧性影响不大;当回火温度达500 ℃时,增加回火次数会降低G95Cr18钢的综合性能。

关键词: G95Cr18不锈钢, 回火, 残留奥氏体, 显微组织, 力学性能

Abstract: Effect of tempering parameters on microstructure of the G95Cr18 steel was investigated by means of OM, SEM and XRD. In addition, the effects of different tempering temperatures and times on hardness, tensile properties and impact property were studied by using Vickers hardness tester, electronic universal testing machine and drop hammer impact testing machine. The results show that the retained austenite content of the G95Cr18 steel decreases gradually with the increase of tempering temperature. When the tempering temperature is 200 ℃, the decomposition amount of retained austenite is less than 3.6%, which is caused by the increase of thermal stability due to the carbon partitioning effect. When the tempering temperature is higher than 400 ℃, the retained austenite content can meet the requirement of＜6%.The hardness of the G95Cr18 steel first decreases and then increases with the increase of tempering temperature, and the secondary hardening temperature is 400 ℃. With the tempering temperature increasing, the impact absorbed energy of the G95Cr18 steel increases first and then decreases. When the tempering temperature is 300 ℃, the impact absorbed energy reaches the maximum, which is 7.1 J. When the tempering temperature is lower than 300 ℃, increasing tempering times has little effect on the microstructure and strength and toughness of the G95Cr18 steel. When the tempering temperature reaches 500 ℃, the comprehensive properties of the G95Cr18 steel decreases with tempering times increasing.

Key words: G95Cr18 stainless steel, tempering, retained austenite, microstructure, mechanical properties

中图分类号:

刘永宝, 周丽娜, 刘明, 高翔, 石东丹. 回火参数对G95Cr18马氏体不锈钢显微组织及力学性能的影响[J]. 金属热处理, 2023, 48(7): 103-110.

Liu Yongbao, Zhou Lina, Liu Ming, Gao Xiang, Shi Dongdan. Effect of tempering parameters on microstructure and mechanical properties of G95Cr18 martensitic stainless steel[J]. Heat Treatment of Metals, 2023, 48(7): 103-110.

参考文献

[1]Wu Baoye, Liu Peng, Wang Xizhao, et al. Effect of laser absorption on picosecond laser ablation of Cr12MoV mold steel, 9Cr18 stainless steel and H13A cemented carbide[J]. Optics Laser Technology, 2018, 101: 11-20.
[2]Feng Xingguo, Zhang Yanshuai, Hu Hanjun, et al. Comparison of mechanical behavior of TiN, TiNC, CrN/TiNC, TiN/TiNC films on G95Cr18 steel by PVD[J]. Applied Surface Science, 2017, 422(15): 266-272.
[3]Aisha M, Mohammed A H A, Ibrahim H S, et al. Analysis of a 440C steel roller bearing using finite element method[J]. Materials Today: Proceedings, 2021, 44: 1750-1754.
[4]Pan L, Kwok C T, LoK T. Friction-stir processing of AISI 440C high-carbon martensitic stainless steel for improving hardness and corrosion resistance[J]. Journal of Materials Processing Technology, 2020, 277: 116448.
[5]王坤, 胡锋, 周雯, 等. 轴承钢研究现状及发展趋势[J]. 中国冶金, 2020, 30(9): 119-128.
Wang Kun, Hu Feng, Zhou Wen, et al. Research status and development trend of bearing steel[J]. China Metallurgy, 2020, 30(9): 119-128.
[6]李慧东, 张覃轶, 刘伟, 等. 深冷处理对440C马氏体不锈钢组织和耐蚀性的影响[J]. 金属热处理, 2022, 47(8): 152-157.
Li Huidong, Zhang Qinyi, Liu Wei, et al. Effect of deep cryogenic treatment on microstructure and corrosion resistance of 440C martensitic stainless steel[J]. Heat Treatment of Metals, 2022, 47(8): 152-157.
[7]安敏, 付中元, 袁超, 等. 淬火后清洗和冷处理工艺对9Cr18钢轴承套圈残留奥氏体含量的影响[J]. 金属热处理, 2021, 46(6): 21-24.
An Min, Fu Zhongyuan, Yuan Chao, et al. Effects of post-quenching cleaning and cold treatment process on retained austenite content of 9Cr18 steel bearing ring[J]. Heat Treatment of Metals, 2021, 46(6): 21-24.
[8]李炯辉. 金属材料金相图谱: 上册[M]. 北京: 机械工业出版社, 2006.
[9]李付伟. 高压气淬后G95Cr18钢的组织和性能[J]. 热处理技术与装备, 2018, 39(2): 41-43.
Li Fuwei. Microstructure and properties of 9Cr18 steel after high pressure gas quenching[J]. Heat Treatment Technology and Equipment, 2018, 39(2): 41-43.
[10]Zhang Jiazhi, Dai Zongbiao, Zeng Liyang, et al. Revealing carbide precipitation effects and their mechanisms during quenching-partitioning-tempering of a high carbon steel: Experiments and modeling[J]. Acta Materialia, 2021, 217: 117176.
[11]司志旺, 符寒光. 合金钢淬火-配分工艺研究进展[J]. 钢铁, 2022, 57(6): 120-131.
Si Zhiwang, Fu Hanguang. Research progress of quenching and partitioning process for alloy steel[J]. Iron and Steel, 2022, 57(6): 120-131.
[12]Ghosh S, Rakha K, Reza S, et al. Atomic scale characterization of carbon partitioning and transition carbide precipitation in a medium carbon steel during quenching and partitioning process[J]. Materials Today: Proceedings, 2022, 62: 7570-7573.
[13]Shi Lei, Cui Xiufang, Li Jian, et al. Role of multiple mid-temperature tempering on mechanical properties and wear behavior of carburized steel under complex service conditions[J]. Surface and Coatings Technology, 2022, 49: 128932.
[14]匡成阳, 马煜林, 王辰昱, 等. 回火温度对耐热钢组织和性能的影响[J]. 金属热处理, 2022, 47(7): 129-133.
Kuang Chengyang, Ma Yulin, Wang Chenyu, et al. Effect of tempering temperature on microstructure and properties of heat-resistant steel[J]. Heat Treatment of Metals, 2022, 47(7): 129-133.
[15]周丽娜. 淬火-碳分配-回火对M50钢微观组织及性能影响研究[D]. 哈尔滨: 哈尔滨工业大学, 2019.
Zhou Lina. Effect of quenching-partitioning-tempering process on microstructure and properties of M50 steel[D]. Harbin: Harbin Institute of Technology, 2019.
[16]李红涛, 叶健熠, 曾献智, 等. G95Cr18钢不同回火温度下的冲击韧度与断口形貌[J]. 轴承, 2014, 12: 28-30.
Li Hongtao, Ye Jianyi, Zeng Xianzhi, et al. Impact toughness and fracture morphology of G95Cr18 tempered at different temperatures[J]. Bearing, 2014, 12: 28-30.

回火参数对G95Cr18马氏体不锈钢显微组织及力学性能的影响

Effect of tempering parameters on microstructure and mechanical properties of G95Cr18 martensitic stainless steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	吴忠潮, 周拥军, 段宝玉, 侯渊, 呼云飞, 高占勇. 20Si2Mn2CrNi钢Ms点下的等温转变组织及其强韧性[J]. 金属热处理, 2023, 48(7): 15-21.
[2]	刘宜林, 陈如柑, 贾玉心, 李玉胜, 范雯, 郑小腾. 异构中碳双相钢丝的微观组织与力学性能[J]. 金属热处理, 2023, 48(7): 32-37.
[3]	陈俊, 张覃轶, 邓锦强, 袁胜福, 周鸿锋, 伍冬. 马氏体不锈钢回火过程中碳化物的演变规律及其对耐蚀性的影响[J]. 金属热处理, 2023, 48(7): 38-43.
[4]	李爽, 王真, 付俊薇, 夏明媚, 滑英丽, 张铮. 新型Cr-Mo-V热冲压模具钢的热导率和回火稳定性[J]. 金属热处理, 2023, 48(7): 66-72.
[5]	韩顺, 李刚, 杨豪, 厉鑫洋, 厉勇, 王春旭. 回火温度对N63钢组织及力学性能的影响[J]. 金属热处理, 2023, 48(7): 79-83.
[6]	靖青秀, 韦丹丹, 魏渺, 杨雪晴, 肖翔鹏, 黄晓东. 形变热处理对Cu-6Ni-3Ti合金组织和性能的影响[J]. 金属热处理, 2023, 48(7): 91-96.
[7]	朱嘉欣, 孙有平, 陈少机, 谢尚恒, 周勇. 固溶时效处理对Mg-4Zn-0.3Zr合金显微组织及阻尼性能的影响[J]. 金属热处理, 2023, 48(7): 97-102.
[8]	王军亮, 周铁柱, 付利国, 郁炎, 李春辉. 去应力退火对B10铜镍合金厚壁三通表面残余应力及组织性能的影响[J]. 金属热处理, 2023, 48(7): 111-116.
[9]	龚雪婷, 赵吉庆, 杨钢, 杨滨. 回火温度对20Cr1Mo1VTiB螺栓钢组织和性能的影响[J]. 金属热处理, 2023, 48(7): 117-123.
[10]	赵何明. 基于感应回火的梯度性能刀圈的制备工艺[J]. 金属热处理, 2023, 48(7): 124-130.
[11]	唐鹏, 黄嘉良, 刘倩男, 邓松云. 时效时间对7075-T6铝合金组织与性能的影响[J]. 金属热处理, 2023, 48(7): 131-137.
[12]	熊雪刚, 陈述, 陈述, 吕兵, 张开华, 周磊磊, 周伟. 回火工艺对Q125高强油井管用钢组织和性能的影响[J]. 金属热处理, 2023, 48(7): 138-142.
[13]	胡武, 吴艳梅, 黄显赞, 黄炎毅, 廖斌. 预处理对6082铝合金型材性能的影响[J]. 金属热处理, 2023, 48(7): 143-147.
[14]	王浩军, 胡生双, 肖君, 张颖, 张颖云, 高婷婷, 欧阳德来. B-Ti57CuZrNi钎料对接钎焊TC4钛合金接头的组织和性能[J]. 金属热处理, 2023, 48(7): 148-151.
[15]	王会敏, 李炎光, 吴静依. 固溶时间对2219铝合金组织和力学性能的影响[J]. 金属热处理, 2023, 48(7): 152-156.