冷却速率和Nb微合金化对25MnV非调质钢组织和硬度的影响

doi:10.13251/j.issn.0254-6051.2024.08.005

金属热处理 ›› 2024, Vol. 49 ›› Issue (8): 31-35.DOI: 10.13251/j.issn.0254-6051.2024.08.005

冷却速率和Nb微合金化对25MnV非调质钢组织和硬度的影响

刘运娜¹, 孙笠灿², 戴观文¹, 刘献达¹, 宋仁伯², 张朝磊³

1.河钢集团石钢公司, 河北石家庄 050031;
2.北京科技大学材料科学与工程学院, 北京 100083;
3.北京科技大学碳中和研究院, 北京 100083

收稿日期:2024-02-06 修回日期:2024-06-14 出版日期:2024-08-25 发布日期:2024-09-27
通讯作者: 宋仁伯,教授,博士,E-mail:Songrb@mater.ustb.edu.cn
作者简介:刘运娜(1981—),女,高级工程师,硕士,主要研究方向为特殊钢材料分析,E-mail:liuyunnasggs@126.com。
基金资助:
河北省重大科技成果转化专项(22281004Z);河钢集团重点科技项目(HG2022114)

Effects of cooling rate and Nb microalloying on microstructure and hardness of 25MnV non-quenched and tempered steel

Liu Yunna¹, Sun Lican², Dai Guanwen¹, Liu Xianda¹, Song Renbo², Zhang Chaolei³

1. HBIS Group Shijiazhuang Iron and Steel Co., Ltd., Shijiazhuang Hebei 050031, China;
2. School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083, China;
3. Institute for Carbon Neutrality, University of Science and Technology Beijing, Beijing 100083, China

Received:2024-02-06 Revised:2024-06-14 Online:2024-08-25 Published:2024-09-27

摘要/Abstract

摘要： 设计了含V和含V-Nb两种成分体系的非调质锻钢,在Gleeble-3800热模拟机上进行了单次压缩试验,研究了冷却速率对V和V-Nb微合金非调质钢组织和硬度的影响。结果表明,冷却速率对钢的显微组织和硬度有显著影响。V钢和V-Nb钢在连续冷却条件下,在0.1~0.5 ℃/s冷却速率范围内,随着冷却速率的增加,铁素体含量减少,珠光体含量增多,组织得到细化;在1~3 ℃/s冷却速率范围内,随着冷却速率的增加,组织进一步细化,同时开始发生贝氏体相变,促进了硬度的提高。Nb元素的加入生成了大尺寸的(V,Nb)(C,N)沉淀颗粒,通过钉扎晶界和诱导晶内铁素体生成进一步细化了晶粒,同时Nb元素对C原子的溶质拖拽效应降低了V-Nb钢中的珠光体含量。在0.1~0.5 ℃/s冷却速率范围内,V钢较高的硬度(218~242 HV)是因为其更高的珠光体含量;在1~3 ℃/s冷却速率范围内,V-Nb钢较高的硬度(256~291 HV)是因为组织细化作用和更高的贝氏体含量。

关键词: 非调质钢, Nb微合金化, 冷却速率, 微观组织, 硬度

Abstract: Effect of cooling rate on microstructure and hardness of two non-quenched and tempered forged steels microalloyed with V and V-Nb was studied by single compression test carried out on a Gleeble-3800 thermal simulator. The results show that the cooling rate has a significant effect on the microstructure and hardness of the tested steels. Under the condition of continuous cooling, with the increase of cooling rate in the range of 0.1-0.5 ℃/s, the ferrite content decreases, the pearlite content increases, and the microstructure is refined. With the increase of cooling rate in the range of 1-3 ℃/s, the microstructure is further refined, and bainite transformation begins to occur, which promotes the increase of hardness. The addition of Nb element generates large-size (V, Nb)(C, N) precipitated particles, which further refines the grains by pinning the grain boundary and inducing the formation of intragranular ferrite. At the same time, the solute drag effect of Nb atom on C atom reduces the content of pearlite in the V-Nb steel. The higher hardness(218-242 HV) of the V steel in the cooling rate range of 0.1-0.5 ℃/s is due to its higher content of pearlite, and the higher hardness(256-291 HV) of the V-Nb steel within the cooling rate range of 1-3 ℃/s is due to the refinement of the microstructure and higher bainite content.

Key words: non-quenched and tempered steel, Nb microalloying, cooling rate, microstructure, hardness

中图分类号:

TG142.1

刘运娜, 孙笠灿, 戴观文, 刘献达, 宋仁伯, 张朝磊. 冷却速率和Nb微合金化对25MnV非调质钢组织和硬度的影响[J]. 金属热处理, 2024, 49(8): 31-35.

Liu Yunna, Sun Lican, Dai Guanwen, Liu Xianda, Song Renbo, Zhang Chaolei. Effects of cooling rate and Nb microalloying on microstructure and hardness of 25MnV non-quenched and tempered steel[J]. Heat Treatment of Metals, 2024, 49(8): 31-35.

参考文献

[1]]丁洁. 汽车用微合金非调质钢的应用现状及发展[J]. 金属热处理, 2006, 31(9): 46-48.
Ding Jie. Present situation of application and development of microalloyed steel for automobile[J]. Heat Treatment of Metals, 2006, 31(9): 46-48.
[2]]蒋泓清, 黄先亮, 黄志兵. 非调质钢的性能影响因素与发展现状[J]. 金属世界, 2013(5): 37-40.
Jiang Hongqing, Huang Xianliang, Huang Zhibing. Influencing factors and development status of non-quenched tempered steel[J]. Metal World, 2013(5): 37-40.
[3]]陈蕴博. 微合金非调质钢的研究与应用进展[C]//技术创新·企业发展——新材料与装备制造论坛. 江阴, 2012.
[4]]蒋波, 冯奕洁, 王芝林, 等. 汽车用铁素体-珠光体型非调质钢研究现状[J]. 钢铁, 2023, 58(3): 11-24.
Jiang Bo, Feng Yijie, Wang Zhilin, et al. Research status of ferrite-pearlite non-quenched and tempered steel for automotive[J]. Iron and Steel, 2023, 58(3): 11-24.
[5]]巫宇峰, 惠卫军, 陈思联, 等. 钒对中碳非调质钢组织性能的影响[J]. 钢铁研究学报, 2016, 28(11): 56-62.
Wu Yufeng, Hui Weijun, Chen Silian, et al. Influence of vanadium on microstructure and mechanical properties of medium carbon forging steel[J]. Journal of Iron and Steel Research, 2016, 28(11): 56-62.
[6]]刘洁, 吴丹, 杨秀娟, 等. 非调质钢的研究现状及发展趋势[J]. 热加工工艺, 2021, 50(23): 1-6.
Liu Jie, Wu Dan, Yang Xiujuan, et al. Research status and development trend of non-quenched and tempered steel[J]. Hot Working Technology, 2021, 50(23): 1-6.
[7]]Liu J X, Peng T E, Tian Z W, et al. Effect of cooling rate and Nb on the microstructure and hardness variation in microalloying medium-carbon non-quenched and tempered steel simulated in a die forging process[J]. Journal of Materials Engineering and Performance, 2022, 31(8): 6561-6571.
[8]]罗灶明. 非调质钢的应用及展望[J]. 福建冶金, 2018, 47(4): 52-56.
Luo Zaoming. Application and prospect of non-quenched and tempered steel[J]. Fujian Metallurgy, 2018, 47(4): 52-56.
[9]]田紫维, 姚彦欣, 刘佳兴, 等. 冷却速度对微合金化中碳非调质钢组织和性能的影响[J]. 金属热处理, 2022, 47(7): 27-33.
Tian Ziwei, Yao Yanxin, Liu Jiaxing, et al. Effect of cooling rate on microstructure and properties of microalloyed medium carbon non-quenched and tempered steel[J]. Heat Treatment of Metals, 2022, 47(7): 27-33.
[10]]余大江, 高加强, 赵四新. Nb对C38+N2非调质钢组织和力学性能的影响[J]. 中国冶金, 2021, 31(5): 92-97.
Yu Dajiang, Gao Jiaqiang, Zhao Sixin. Effect of Nb on microstructure and mechanical properties of non-quenched and tempered steel C38+N2[J]. China Metallurgy, 2021, 31(5): 92-97.
[11]]谭利, 肖波, 郑力宁, 等. 轧制比和Nb对V-Ti微合金非调质钢组织及性能的影响[J]. 特殊钢, 2018, 39(5): 58-61.
Tan Li, Xiao Bo, Zheng Lining, et al. Effect of rolling ratio and niobium on microstructures and properties of V-Ti microalloyed non-quenched and tempered steel[J]. Special Steel, 2018, 39(5): 58-61.
[12]]Huang H, Yang G, Zhao G, et al. Effect of Nb on the microstructure and properties of Ti-Mo microalloyed high-strength ferritic steel[J]. Materials Science and Engineering A, 2018, 736: 148-155.
[13]]Zhao F, Zhou N B, Wu M, et al. Intragranular ferrite formed in a V-Ti-N medium-carbon steel containing MnS inclusions[J]. Steel Research International, 2017, 88(12): 1700173.
[14]]Hu J, Du L X, Wang J J. Effect of V on intragranular ferrite nucleation of high Ti bearing steel[J]. Scripta Materialia, 2013, 68(12): 953-956.
[15]Jiang B, Fang W, Chen R M, et al. Mechanical properties and microstructural characterization of medium carbon non-quenched and tempered steel: Microalloying behavior[J]. Materials Science and Engineering A, 2019, 748: 180-188.
[16]]Offerman S E, Wilderen van L J G W, Dijk van N H, et al. In-situ study of pearlite nucleation and growth during isothermal austenite decomposition in nearly eutectoid steel[J]. Acta Materialia, 2003, 51(13): 3927-3938.
[17]]Lee K J, Lee J K. Modelling of γ/α transformation in niobium-containing microalloyed steels[J]. Scripta Materialia, 1999, 40(7): 831-836.
[18]]Tian J Y, Wang H X, Zhu M, et al. Improving mechanical properties in high-carbon pearlitic steels by replacing partial V with Nb[J]. Materials Science and Engineering A, 2022, 834: 142622.
[19]]王新志, 张可, 黄重, 等. Cr-Ni-Cu桥梁耐候钢的连续冷却相变及其组织和硬度[J]. 金属热处理, 2023, 48(2): 17-22.
Wang Xinzhi, Zhang Ke, Huang Zhong, et al. Continuous cooling transformation of Cr-Ni-Cu bridge weathering steel and its microstructure and hardness[J]. Heat Treatment of Metals, 2023, 48(2): 17-22.
[20]]赵丽洋, 刘东博, 谯明亮, 等. Q500qENH耐候桥梁钢形变奥氏体连续冷却转变行为研究[J]. 上海金属, 2022, 44(1): 35-39.
Zhao Liyang, Liu Dongbo, Qiao Mingliang, et al. Study on continuous cooling transformation behavior of deformed austenite for Q500qENH weathering bridge steel[J]. Shanghai Metals, 2022, 44(1): 35-39.

冷却速率和Nb微合金化对25MnV非调质钢组织和硬度的影响

Effects of cooling rate and Nb microalloying on microstructure and hardness of 25MnV non-quenched and tempered steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	华文娟, 张建勋. 时效处理对电弧熔丝增材制造2319铝合金性能及断裂行为的影响[J]. 金属热处理, 2024, 49(8): 60-66.
[2]	刘静, 赵科, 王丽阁. 退火对Co_xFe₃₅Mn₂₅Cr₁₅Ni₁₀Ti₅高熵合金微观组织及硬度的影响[J]. 金属热处理, 2024, 49(8): 94-101.
[3]	周瑞虎, 樊启刚, 曾志鹏. 轴承套圈碳氮共渗工艺的改进[J]. 金属热处理, 2024, 49(8): 152-155.
[4]	孙昭琦, 李涛, 韩强, 张行刚, 白岩松, 高志敏. 淬火工艺对28MnCrMoRE油井管钢显微组织及硬度的影响[J]. 金属热处理, 2024, 49(8): 160-164.
[5]	刘梓峰, 赵旭亮, 罗皓. 淬火温度对4Cr4Mo3W2V1模具钢组织与硬度的影响[J]. 金属热处理, 2024, 49(8): 170-173.
[6]	梁科, 武猛, 张习烨, 行志刚. 退火温度对汽车后背门板用Fe-0.12C-4.85Mn-0.24Si钢组织与力学性能的影响[J]. 金属热处理, 2024, 49(8): 174-177.
[7]	李峰. 钛改性离子渗氮处理对沉淀硬化钢性能的影响[J]. 金属热处理, 2024, 49(8): 183-188.
[8]	丁红珍, 李航, 邱万奇. 变电场辅助低温渗硼制备单相Fe₂B渗层[J]. 金属热处理, 2024, 49(8): 195-199.
[9]	王岗, 杨舜明, 匡光辉. 3105铝合金铸锭的均匀化[J]. 金属热处理, 2024, 49(8): 200-203.
[10]	杜茂华, 张振新, 毕贵军, 曹立超. 激光熔覆420不锈钢的热流耦合数值模拟与试验验证[J]. 金属热处理, 2024, 49(8): 211-219.
[11]	陈保安, 李梦琳, 陈瑞, 多俊龙, 韩钰, 祝志祥, 杨长龙, 缪姚军. 添加稀土对Al-Mg-Si合金微观组织和性能的影响[J]. 金属热处理, 2024, 49(7): 100-105.
[12]	周蕾, 王莹, 张永健, 赵晓丽, 惠卫军. V+Ti微合金化Mn-Cr系贝氏体型非调质钢的氢脆敏感性[J]. 金属热处理, 2024, 49(7): 106-112.
[13]	黄剑涛, 张明赫, 冯运莉, 尹绍江, 陈春生, 王厚昕. V-Nb微合金化Q420B大规格角钢的连续冷却转变规律[J]. 金属热处理, 2024, 49(7): 121-127.
[14]	陈作宁, 师仲然, 胡骞, 展之德, 罗小兵. 390 MPa级抗碰撞船体钢的奥氏体连续冷却转变[J]. 金属热处理, 2024, 49(7): 146-151.
[15]	罗长增, 曾笑笑, 魏东博, 李旭聪, 陈月春, 林慕尧, 张平则. 基于双辉技术的气门盘锥面TiN涂层制备和高温摩擦行为[J]. 金属热处理, 2024, 49(7): 195-199.