碳含量与热处理对高铌钛铝合金微观组织及力学性能的影响

doi:10.13251/j.issn.0254-6051.2024.08.002

金属热处理 ›› 2024, Vol. 49 ›› Issue (8): 9-14.DOI: 10.13251/j.issn.0254-6051.2024.08.002

碳含量与热处理对高铌钛铝合金微观组织及力学性能的影响

高玉魁, 方文奕

同济大学材料科学与工程学院, 上海 210804

收稿日期:2024-02-05 修回日期:2024-06-12 出版日期:2024-08-25 发布日期:2024-09-27
作者简介:高玉魁(1973—),男,教授,博士,主要研究方向为先进金属材料热处理及力学性能,E-mail:yukuigao@tongji.edu.cn

Effects of carbon content and heat treatment on microstructure and mechanical properties of TiAl alloys with high Nb

Gao Yukui, Fang Wenyi

School of Materials Science and Engineering, Tongji University, Shanghai 210804, China

Received:2024-02-05 Revised:2024-06-12 Online:2024-08-25 Published:2024-09-27

摘要/Abstract

摘要： 以Ti-44Al-8Nb-xC(x=0, 0.3, 0.6) 合金为研究对象,研究了3种不同碳含量和两种不同温度的时效处理对合金的微观组织、显微硬度及高温拉伸性能的影响。结果表明:碳含量升高到0.6%时,合金中析出了Ti₂AlC;时效温度从800 ℃升高到900 ℃时,含碳合金中析出了Ti₃AlC。碳含量的增加和时效温度的升高都有利于提升合金的显微硬度和850 ℃抗拉强度,显微硬度最高为(477.6±9.1) HV0.3,850 ℃抗拉强度最高为(605.07±5.01) MPa,较最低抗拉强度提高了32.7%。断后伸长率与合金中碳化物数量及尺寸有关,拉伸断口都表现为脆性断裂;碳含量为0.3%,经900 ℃时效后合金拥有最好的塑性,断后伸长率最高,为5.41%±0.42%,较最低伸长率提升了67.5%。

关键词: 高Nb-TiAl合金, 碳含量, 热处理, 微观结构, 力学性能

Abstract: Taking Ti-44Al-8Nb-xC(x=0, 0.3, 0.6) alloys as the research object, the effects of three different carbon contents and two aging temperatures on the microstructure, microhardness and high-temperature tensile properties were studied. The results show that when the carbon content increases to 0.6%, Ti₂AlC precipitates in the alloy. When the aging temperature increases from 800 ℃ to 900 ℃, Ti₃AlC precipitates in the alloy containing carbon. The increase in carbon content and aging temperature are all beneficial to improving the microhardness and tensile strength at 850 ℃ of the alloy, where the highest microhardness is (477.6±9.1) HV0.3, and the highest tensile strength at 850 ℃ is (605.07±5.01) MPa, which increases by 32.7% compored to the lowest tensile strength. The elongation is related to the number and size of carbides, and all the tensile fractures show brittle fracture. The alloy with 0.3% carbon has the best plasticity when aged at 900 ℃, the highest elongation is 5.41%±0.42%, which increases by 67.5% compared to the lowest elongation.

Key words: high Nb-TiAl alloy, carbon content, heat treatment, microstructure, mechanical properties

中图分类号:

TG146.2

高玉魁, 方文奕. 碳含量与热处理对高铌钛铝合金微观组织及力学性能的影响[J]. 金属热处理, 2024, 49(8): 9-14.

Gao Yukui, Fang Wenyi. Effects of carbon content and heat treatment on microstructure and mechanical properties of TiAl alloys with high Nb[J]. Heat Treatment of Metals, 2024, 49(8): 9-14.

参考文献

[1]Zhang Weijun, Deevi S, Chen Guoliang. On the origin of superior high strength of Ti-45Al-10Nb alloys[J]. Intermetallics, 2002, 10(5): 403-406.
[2]葛阳, 洪大军, 张帅, 等. 时效对新型Ti-Al-V中熵合金组织性能的影响[J]. 金属热处理, 2021, 46(6): 129-132.
Ge Yang, Hong Dajun, Zhang Shuai, et al. Effect of aging on microstructure and properties of a new type of Ti-Al-V medium-entropy alloy[J]. Heat Treatment of Metals, 2021, 46(6): 129-132.
[3]卢威, 金莹, 刘素芬, 等. Ti-Al系金属间化合物在均匀化热处理中的微观结构演变[J]. 金属热处理, 2019, 44(6): 42-46.
Lu Wei, Jin Ying, Liu Sufeng, et al. Microstructure evolution of Ti-Al intermetallics during homogenization heat treatment[J]. Heat Treatment of Metals, 2019, 44(6): 42-46.
[4]Cao Jun, Sun Tieliang, Guo Zhichao, et al. Enhancement of room-temperature mechanical properties of TiAl alloy by trace addition of C[J]. Materials Science and Engineering A, 2023, 884: 145598.
[5]杨锐. 钛铝金属间化合物的进展与挑战[J]. 金属学报, 2015, 51: 129-147.
Yang Rui. Advances and challenges of TiAl base alloys[J]. Acta Metallurgica Sinica, 2015, 51: 129-147.
[6]Kim Y. Gamma titanium aluminides: Their status and future[J]. JOM, 1995, 47(7): 39-42.
[7]Chen Guoliang, Sun Zuqing, Zhou Xing. Oxidation and mechanical behavior of intermetallic alloys in the Ti-Nb-Al ternary system[J]. Materials Science and Engineering A, 1992, 153(1-2): 597-601.
[8]Voice W, Henderson M, Shelton E, et al. Gamma titanium aluminide, TNB[J]. Intermetallics, 2005, 13: 959-964.
[9]Liu Jinhu, Zhang Fuqiang, Nan Hai, et al. Effect of Caddition on as-cast microstructures of high Nb containing TiAl alloys[J]. Metals, 2019, 9(11): 1201.
[10]Lapin J, Štamborská M, Kamyshnykova K, et al. Room temperature mechanical behaviour of cast in-situ TiAl matrix composite reinforced with carbide particles[J]. Intermetallics, 2019, 105: 113-123.
[11]Liang Zhenquan, Xiao Shulong, Yu Hongbao, et al. Enhanced high temperature tensile and creep properties of a β-solidified γ-TiAl alloy with the hybrid addition of C and Y₂O₃[J]. Intermetallics, 2022, 150: 107698.
[12]Li Mingao, Xiao Shulong, Chen Yuyong, et al. The effect of carbon addition on the high-temperature properties of β solidification TiAl alloys[J]. Journal of Alloys and Compounds, 2019, 775: 441-448.
[13]郭雷明, 王文焱, 黄亚博, 等. 退火工艺对铸轧钛铝复合板界面组织与性能的影响[J]. 金属热处理, 2018, 43(4): 194-198.
Guo Leiming, Wang Wenyan, Huang Yabo, et al. Effect of annealing process on microstructure and properties of interface of cast and rolled Ti-Al composite plate[J]. Heat Treatment of Metals, 2018, 43(4): 194-198.
[14]Yue Hangyu, Peng Hui, Li Ruifeng, et al. Effect of heat treatment on the microstructure and anisotropy of tensile properties of TiAl alloy produced via selective electron beam melting[J]. Materials Science and Engineering A, 2021, 803: 140473.
[15]Chlupova A, Heczko M, Obrtlik M, et al. Effect of heat-treatment on the microstructure and fatigue properties of lamellar γ-TiAl alloyed with Nb, Mo and/or C[J]. Materials Science and Engineering A, 2020, 786: 139427.
[16]Chen Liu, Zhu Langping, Guan Yongjun, et al. Tougher TiAl alloy via integration of hot isostatic pressing and heat treatment[J]. Materials Science and Engineering A, 2017, 688: 371-377.
[17]Song Lin, Hu Xingguo, Wang Li, et al. Microstructure evolution and enhanced creep property of a high Nb containing TiAl alloy with carbon addition[J]. Journal of Alloys and Compounds, 2019, 807: 151649.
[18]Chen Ruirun, Fang Hongze, Chen Xiaoyu, et al. Formation of TiC/Ti₂AlC and α₂+γ in in-situ TiAl composites with different solidification paths[J]. Intermetallics, 2017, 81: 9-15.

碳含量与热处理对高铌钛铝合金微观组织及力学性能的影响

Effects of carbon content and heat treatment on microstructure and mechanical properties of TiAl alloys with high Nb

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	张宏亮, 周春波, 侯燕, 蒋志强. C-Si-Mn系配分钢的研究进展[J]. 金属热处理, 2024, 49(8): 22-30.
[2]	曾祥军, 史志铭, 赵鸽, 廉浩, 刘佳成. 轻-重稀土混合添加对Al-Si-Mg合金显微组织和力学性能的影响[J]. 金属热处理, 2024, 49(8): 36-41.
[3]	曹悦, 高雪云, 王海燕, 邢磊, 林鸿亮. 稀土La对含Cu马氏体不锈钢显微组织与力学性能的影响[J]. 金属热处理, 2024, 49(8): 42-47.
[4]	白瑞, 杜云飞, 贺秀丽, 梁红玉. Al含量对高锰高铝轻质钢组织和力学性能的影响[J]. 金属热处理, 2024, 49(8): 48-52.
[5]	徐超, 曹欣旺, 王晨阳, 王玉婷, 张倩, 杨其全, 胡杰. 热处理工艺对高速列车用51CrV4钢轴箱弹簧力学性能及服役性能的影响[J]. 金属热处理, 2024, 49(8): 53-59.
[6]	华文娟, 张建勋. 时效处理对电弧熔丝增材制造2319铝合金性能及断裂行为的影响[J]. 金属热处理, 2024, 49(8): 60-66.
[7]	王堤鹤, 庞启航, 赵星宇, 李维娟, 赵立冬, 史津铭. IQ&P工艺处理高强钢的组织性能及低温C配分[J]. 金属热处理, 2024, 49(8): 74-81.
[8]	王春兴, 李明. 退火处理对CoCrFeNiMn高熵合金组织和性能的影响[J]. 金属热处理, 2024, 49(8): 102-107.
[9]	任云飞, 潘新元, 万天剑, 李景辉, 张明亚. T6热处理对高压压铸ADC12铝合金微观结构和性能的影响[J]. 金属热处理, 2024, 49(8): 108-112.
[10]	迟蕊, 徐志远, 孟双, 李延成, 徐扬帆, 李涛. 中间退火温度对6016铝合金组织及性能的影响[J]. 金属热处理, 2024, 49(8): 113-118.
[11]	郭昊东, 杨超飞, 孙磊, 张玉祥, 黄冬, 仝智远. 10CrNi8MoV钢的包申格效应及恢复热处理[J]. 金属热处理, 2024, 49(8): 119-123.
[12]	徐锋, 孙强, 孟吉炜. 固溶温度对超低碳15-5PH沉淀硬化不锈钢组织和性能的影响[J]. 金属热处理, 2024, 49(8): 124-129.
[13]	张勇, 李如杨, 马青山, 胡效东. 热处理对09MnNiDR低温钢焊接接头组织及力学性能的影响[J]. 金属热处理, 2024, 49(8): 136-142.
[14]	刘晨希, 胡昕明, 欧阳鑫, 邢梦楠, 白云峰. 回火时间对低焊接裂纹敏感性压力容器用钢组织性能的影响[J]. 金属热处理, 2024, 49(8): 143-146.
[15]	曲之国, 张万新, 白学飞, 王东明, 张友建. 模拟焊后热处理对厚规格16MnDR钢板组织性能的影响[J]. 金属热处理, 2024, 49(8): 147-151.