XGTC300L搪瓷钢的连续冷却转变行为与析出规律

doi:10.13251/j.issn.0254-6051.2024.09.013

金属热处理 ›› 2024, Vol. 49 ›› Issue (9): 80-85.DOI: 10.13251/j.issn.0254-6051.2024.09.013

XGTC300L搪瓷钢的连续冷却转变行为与析出规律

袁静¹, 陈飞达², 钟海清¹, 唐小勇¹, 朱映玉¹, 冷烨旻¹, 肖虎², 田世伟²

1.新余钢铁股份有限公司, 江西新余 338000;
2.北京科技大学工程技术研究院, 北京 100083

收稿日期:2024-03-09 修回日期:2024-07-04 出版日期:2024-09-25 发布日期:2024-10-29
通讯作者: 钟海清,高级工程师,E-mail: zhq@xinsteel.com.cn
作者简介:袁静(1982—),男,高级工程师,博士,主要研究方向为钢铁冶金相关专业技术,E-mail: yaya116782@sina.com。
基金资助:
国家自然科学基金(52201101,52274372);国家重点研发计划(2021YFB3702404)

Continuous cooling transformation behavior and precipitation pattern of XGTC300L enamelled steel

Yuan Jing¹, Chen Feida², Zhong Haiqing¹, Tang Xiaoyong¹, Zhu Yingyu¹, Leng Yemin¹, Xiao Hu², Tian Shiwei²

1. Xinyu Iron and Steel Co., Ltd., Xinyu Jiangxi 338000, China;
2. Institute of Engineering Technology, Beijing University of Science and Technology, Beijing 100083, China

Received:2024-03-09 Revised:2024-07-04 Online:2024-09-25 Published:2024-10-29

摘要/Abstract

摘要： 采用Gleeble-3500热模拟试验机获得了XGTC300L搪瓷钢在不同冷却速度下的温度-膨胀量曲线,通过对不同冷速下试样的显微组织特征和硬度变化规律进行研究,绘制了钢的动态CCT曲线。结果显示,热变形后的XGTC300L搪瓷钢在0.2~50 ℃/s冷速区间冷却时,其基体组织均为铁素体,且随着冷速的增加铁素体晶粒尺寸逐渐减小。在0.2 ℃/s冷速下,钢的硬度值最低,约为96.6 HV0.1;在0.5~5 ℃/s的冷速区间内,钢的硬度值变化不大,约为110.0 HV0.1;在10~30 ℃/s的冷速区间内,钢的硬度值约为120.0 HV0.1;在50 ℃/s冷速下硬度值达到最高,约为137.9 HV0.1。在30 ℃/s的快冷速下,铁素体的基体和晶界处均发现了含硼碳化物析出,而在0.2 ℃/s的慢冷速下仅有条状渗碳体在晶界析出。在0.2~50 ℃/s冷速区间,随着冷速的增加,相转变开始温度由850 ℃降至810 ℃,相转变终了温度由840 ℃降至750 ℃,且转变时间逐渐缩短。动态CCT曲线中仅发现了铁素体相区,未发现贝氏体或马氏体转变相区。因此XGTC300L搪瓷钢的轧后控冷工艺应采取大于30 ℃/s的较高冷速,以获得较小的铁素体晶粒和一定量的含硼析出物,从而提高其综合性能。

关键词: XGTC300L搪瓷钢, 热模拟, 动态CCT曲线, 析出物

Abstract: Temperature-expansion curves of the XGTC300L enamelled steel at different cooling rates were obtained by a Gleeble-3500 thermal simulation test machine. The dynamic CCT curve of the steel was drawn by studying the microstructure characteristics and hardness variation of the specimens at different cooling rates. The results show that the matrix of the XGTC300L enamelled steel after hot deformation consists of ferrite when cooled within the range of 0.2-50 ℃/s, and the ferrite grain size decreases with the increase of cooling rates. At the cooling rate of 0.2 ℃/s, the steel exhibits the lowest hardness value, about 96.6 HV0.1. In the range of 0.5-5 ℃/s, the hardness value changes little, about 110.0 HV0.1. In the range of 10-30 ℃/s, the hardness value is about 120.0 HV0.1. At the cooling rate of 50 ℃/s, the steel reaches its highest hardness value, about 137.9 HV0.1. At the fast-cooling rate of 30 ℃/s, boron-containing carbides are found in the ferrite matrix and grain boundary, while only strip cementite precipitates at the grain boundary at the slow cooling rate of 0.2 ℃/s. In the range of 0.2-50 ℃/s, with the increase of cooling rate, the start temperature of transformation is decreased from 850 ℃ to 810 ℃, the end temperature of transformation is decreased from 840 ℃ to 750 ℃, and the transformation time decreases gradually. In the dynamic CCT curve, only the ferrite phase region is found, and the phase region of bainite or martensite is not found. Therefore, the controlled cooling process after rolling of the XGTC300L enamelled steel should adopt a higher cooling rate of more than 30 ℃/s to obtain smaller ferrite grains and a certain number of boron-containing precipitates, so as to improve its comprehensive performance.

Key words: XGTC300L enamelled steel, thermal simulation, dynamic CCT curves, precipitates

中图分类号:

TG156.1

袁静, 陈飞达, 钟海清, 唐小勇, 朱映玉, 冷烨旻, 肖虎, 田世伟. XGTC300L搪瓷钢的连续冷却转变行为与析出规律[J]. 金属热处理, 2024, 49(9): 80-85.

Yuan Jing, Chen Feida, Zhong Haiqing, Tang Xiaoyong, Zhu Yingyu, Leng Yemin, Xiao Hu, Tian Shiwei. Continuous cooling transformation behavior and precipitation pattern of XGTC300L enamelled steel[J]. Heat Treatment of Metals, 2024, 49(9): 80-85.

参考文献

[1]孙全社. 宝钢搪瓷用钢的开发与应用[J]. 上海金属, 2005, 27(6): 47-50.
Sun Quanshe. Development and application of enamelleding sheet steels at Baosteel[J]. Shanghai Metals, 2005, 27(6): 47-50.
[2]葛玉静, 徐春. 搪瓷用钢抗鳞爆性能的研究现状[J]. 表面技术, 2016, 45(12): 129-134.
Ge Yujing, Xu Chun. Research status of enamelleded steel fish-scaling resistance[J]. Surface Technology, 2016, 45(12): 129-134.
[3]黄学启, 刘相华, 张志敏, 等. 高强度热轧搪瓷钢搪烧后组织及力学性能研究[J]. 热加工工艺, 2018, 47(18): 227-230.
Huang Xueqi, Liu Xianghua, Zhang Zhimin, et al. Research on microstructure and mechanical properties of high-strength hot rolled enamelled steel after enamelleding[J]. Hot Working Technology, 2018, 47(18): 227-230.
[4]刘再旺, 郭敏, 滕华湘, 等. 退火温度对超深冲搪瓷钢成型性能及再结晶织构的影响[J]. 金属热处理, 2024, 49(3): 91-97.
Liu Zaiwang, Guo Min, Teng Huaxiang, et al. Influence of annealing temperature on formability and recrystallization texture of an extra-deep drawing steel for enamelleding[J]. Heat Treatment of Metals, 2024, 49(3): 91-97.
[5]徐春, 饶德怀. 析出相对超低碳钒钛微合金钢氢渗透及抗鳞爆性的影响[J]. 玻璃与搪瓷, 2016, 44(1): 20-26.
Xu Chun, Rao Dehuai. The effect of precipitation on penetration of hydrogen to ultra-low carbon vanadium titanium alloyed steel and fish scale resistance[J]. Glass Enamelled and Ophthalmic Optics, 2016, 44(1): 20-26.
[6]吴红艳, 杜林秀, 孙士垚, 等. 搪瓷钢组织性能及氢渗透行为研究[J]. 轧钢, 2022, 39(6): 106-112.
Wu Hongyan, Du Linxiu, Sun Shiyao, et al. Study on microstructure, properties and hydrogen permeation behavior of enamelled steel[J]. Steel Rolling, 2022, 39(6): 106-112.
[7]徐春, 杨铭, 庞灵欢, 等. 析出相特征与搪瓷用钢抗鳞爆的关系研究[J]. 玻璃与搪瓷, 2018, 46(6): 12-18.
Xu Chun, Yang Ming, Pang Linghuan, et al. Effect of characteristics of precipitates on fish-scaling resistance of enamelled steel sheet[J]. Glass Enamelled and Ophthalmic Optics, 2018, 46(6): 12-18.
[8]张念, 陈章明, 赵红强, 等. 38MnSiVS5非调质钢的CCT曲线测定与分析[J]. 特殊钢, 2022, 43(1): 82-85.
Zhang Nian, Chen Zhangming, Zhao Hongqiang, et al. Determination and analysis of CCT curves of non-quenched and tempered steel 38MnSiVS5[J]. Special Steel, 2022, 43(1): 82-85.
[9]张永军, 韩静涛, 孔俊其, 等. SCM435热变形奥氏体连续冷却转变行为[J]. 热加工工艺, 2010, 39(2): 38-39.
Zhang Yongjun, Han Jingtao, Kong Junqi, et al. Continuous cooling transformation behavior of hot deformation austenite in SCM435 steel[J]. Hot Working Technology, 2010, 39(2): 38-39.
[10]刘干, 孔祥磊, 黄明浩, 等. 冷却速率对超高强度X90M管线钢相变行为的影响[J]. 金属热处理, 2024, 49(5): 162-167.
Liu Gan, Kong Xianglei, Huang Minghao, et al. Effect of cooling rate on phase transformation behavior of ultra-high strength X90M pipeline steel[J]. Heat Treatment of Metals, 2024, 49(5): 162-167.
[11]董福涛, 杜林秀, 刘相华, 等. 连续退火工艺对含B搪瓷用钢组织性能的影响[J]. 金属学报, 2013, 49(10): 1160-1168.
Dong Futao, Du Linxiu, Liu Xianghua, et al. Influence of continuous annealing process on microstructure and properties of boron containing enamelled steel[J]. Acta Metallurgica Sinica, 2013, 49(10): 1160-1168.
[12]薛雲泽, 徐东, 郑冰, 等. 含硼冷镦钢10B21热变形过程中的静态再结晶行为[J]. 金属热处理, 2024, 49(6): 217-223.
Xue Yunze, Xu Dong, Zheng Bing, et al. Static recrystallization behavior of boron-containing cold heading steel 10B21 during hot deformation[J]. Heat Treatment of Metals, 2024, 49(6): 217-223.

[1]	陈石, 汪家晗, 张云祥, 骆艳萍, 孙钊洋, 叶传龙. HRB400E钢等温热处理过程中的奥氏体晶粒长大和钒析出物的影响[J]. 金属热处理, 2024, 49(8): 15-21.
[2]	王春兴, 李明. 退火处理对CoCrFeNiMn高熵合金组织和性能的影响[J]. 金属热处理, 2024, 49(8): 102-107.
[3]	迟蕊, 徐志远, 孟双, 李延成, 徐扬帆, 李涛. 中间退火温度对6016铝合金组织及性能的影响[J]. 金属热处理, 2024, 49(8): 113-118.
[4]	罗晓阳, 程刚虎, 靳科, 周维莲, 侯园园, 唐兴昌. 20Mn23AlV无磁结构钢热轧板的组织性能及动态再结晶行为[J]. 金属热处理, 2024, 49(7): 91-99.
[5]	黄剑涛, 张明赫, 冯运莉, 尹绍江, 陈春生, 王厚昕. V-Nb微合金化Q420B大规格角钢的连续冷却转变规律[J]. 金属热处理, 2024, 49(7): 121-127.
[6]	刘敏, 郑志鹏, 甘利红, 刘胤辰, 刘震, 张阳, 冯波, 刘春泉. 桁架用Nb-Mo微合金中锰钢强化机理及碳化物析出行为[J]. 金属热处理, 2024, 49(3): 198-203.
[7]	曹佳丽, 靳红泽, 李康立, 徐亚鹏, 赵强, 王翠萍, 李梦楠. 水电用Q690CFD低合金高强钢SH-CCT曲线测定与分析[J]. 金属热处理, 2024, 49(2): 60-65.
[8]	李月云, 王雷, 李建华, 张宇. 大规格SWRS82B钢盘条同圈抗拉强度波动原因分析及改善措施[J]. 金属热处理, 2024, 49(1): 273-278.
[9]	林雄, 满达, 杨宏韬, 侯宇辰, 金自力, 李玮. 奥氏体化参数对25Cr3Ni3MoNb钢700 ℃下变形行为的影响[J]. 金属热处理, 2023, 48(5): 210-216.
[10]	张金城, 孙胜辉, 蔡明晖, 赵文柱, 丁桦. 控轧控冷对Ti-Mo-Nb复合微合金化低碳钢组织和力学性能的影响[J]. 金属热处理, 2023, 48(1): 155-162.
[11]	艾兵权, 邝霜, 田秀刚, 杨峰, 王玉慧, 逯志强, 王朝, 郝雷. 均热温度对不同成分980 MPa级高强钢组织和性能的影响[J]. 金属热处理, 2022, 47(9): 119-124.
[12]	王瑞敏, 刘曼, 周剑华, 张琪, 苏雪, 徐光. R350HT钢轨钢的连续冷却转变曲线[J]. 金属热处理, 2022, 47(9): 153-157.
[13]	李鹏, 李人杰, 杨雄, 黄利. 高强度热镀锌结构钢SGC570的退火工艺[J]. 金属热处理, 2022, 47(8): 223-227.
[14]	马启林, 刘刚, 郑健, 阴树标, 李拔, 刘清友. Nb-V复合微合金化高钢级管线钢的奥氏体连续冷却转变[J]. 金属热处理, 2022, 47(1): 13-18.
[15]	霍喜伟. Cr对20MnSiV门架型钢动态CCT曲线和性能的影响[J]. 金属热处理, 2021, 46(7): 89-93.

XGTC300L搪瓷钢的连续冷却转变行为与析出规律

Continuous cooling transformation behavior and precipitation pattern of XGTC300L enamelled steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价