Cu-Cr-Zr合金搅拌摩擦焊接接头的组织和力学性能

doi:10.13251/j.issn.0254-6051.2020.03.008

金属热处理 ›› 2020, Vol. 45 ›› Issue (3): 35-40.DOI: 10.13251/j.issn.0254-6051.2020.03.008

Cu-Cr-Zr合金搅拌摩擦焊接接头的组织和力学性能

周莎^1,2, 王快社^1,2, 王文^1,2, 彭湃^1,2, 张升懿^1,2, 黄丽颖^1,2

1. 西安建筑科技大学冶金工程学院, 陕西西安 710055;
2. 西安建筑科技大学功能材料加工国家地方联合工程研究中心, 陕西西安 710055

收稿日期:2019-09-13 出版日期:2020-03-25 发布日期:2020-04-03
通讯作者: 王文,高级工程师,博士,主要从事有色金属搅拌摩擦焊接和搅拌摩擦加工,E-mail:wangwen2016@126.com
作者简介:周莎(1992—),女,硕士研究生,主要从事有色金属搅拌摩擦焊接和搅拌摩擦加工,E-mail:sunia@163.com。
基金资助:
国家自然科学基金(U1760201,51574192,51404180)

Microstructure and mechanical properties of friction stir welding joint of Cu-Cr-Zr alloy

Zhou Sha^1,2, Wang Kuaishe^1,2, Wang Wen^1,2, Peng Pai^1,2, Zhang Shengyi^1,2, Huang Liying^1,2

1. School of Metallurgical Engineering, Xi'an University of Architecture and Technology, Xi'an Shaanxi 710055, China;
2. National and Local Joint Engineering Research Center for Functional Materials Processing, Xi'an University of Architecture and Technology, Xi'an Shaanxi 710055, China

Received:2019-09-13 Online:2020-03-25 Published:2020-04-03

摘要/Abstract

摘要：

采用旋转速度为750和1500 r/min,焊接速度为23.5 mm/min的焊接参数分别对时效态和固溶态的3 mm厚的Cu-Cr-Zr合金板进行搅拌摩擦焊接,研究转速及母材区(BM)初始状态对搅拌摩擦焊(FSW)接头的微观组织与力学性能的影响,并对接头的力学性能进行模型化定量分析。结果表明:FSW后,接头晶粒显著细化,沉淀相在搅拌头的高温热作用下固溶在基体中。当BM的初始状态为时效态时,与1500 r/min样品相比,750 r/min样品晶粒尺寸较小且存在沉淀相,750 r/min样品力学性能较高,主要是晶界强化和沉淀强化的作用。当BM的初始状态为固溶态时,与1500 r/min样品相比,750 r/min样品晶粒尺寸较小,力学性能较高,主要是晶界强化的作用。当FSW转速相同时,时效态接头的晶粒尺寸小于固溶态接头,而力学性能高于固溶态接头,主要是由于BM的初始组织状态不同导致的。综合分析表明:FSW过程中选用低转速焊接,可以获得性能较优的接头。

关键词: Cu-Cr-Zr合金, 搅拌摩擦焊接, 组织, 力学性能

Abstract:

Friction stir welding (FSW) was conducted on Cu-Cr-Zr alloy plates with 3 mm thickness by using rotation speed of 750 and 1500 r/min and welding speed of 23.5 mm /min, in the state of aged and solid solution treated respectively. The effects of rotation speed and base metal (BM) initial state on the microstructure and mechanical properties of the FSW joints were studied, and the mechanical properties of joints were modeled and quantitatively analyzed. The results show that the grain size of the FSW joint significantly refines, and the precipitated phase is dissolved in the matrix under the high-temperature effect of the stir-welding head. When the initial state of BM is aged state, compared with the specimens of 1500 r/min, the grain size of the 750 r/min specimens is smaller, and there exists precipitate phase in the matrix, so that the 750 r/min specimens have higher mechanical properties mainly due to the comprehensive effect of grain boundary strengthening and precipitation strengthening. When the initial state of BM is solid solution state, compared with the specimens of 1500 r/min, the 750 r/min specimens have smaller grain size and high mechanical properties mainly due to grain boundary strengthening effect. When the FSW speed is the same, the welding joint grain size of the aged state is smaller than that of solid solution state, but the mechanical properties of the aged state is higher than that of solid solution state, which is mainly due to the difference of the initial state microstructures. The comprehensive analysis shows that a welding joint with better performance can be obtained by the FSW process with a lower welding speed.

Key words: Cu-Cr-Zr alloy, friction stir welding, microstructure, mechanical properties

中图分类号:

TG456.5

周莎, 王快社, 王文, 彭湃, 张升懿, 黄丽颖. Cu-Cr-Zr合金搅拌摩擦焊接接头的组织和力学性能[J]. 金属热处理, 2020, 45(3): 35-40.

Zhou Sha, Wang Kuaishe, Wang Wen, Peng Pai, Zhang Shengyi, Huang Liying. Microstructure and mechanical properties of friction stir welding joint of Cu-Cr-Zr alloy[J]. HTM, 2020, 45(3): 35-40.

参考文献

[1]Zhang S J, Li R G, Kang H J, et al. A high strength and electrical conductivity Cu-Cr-Zr alloy fabricated by cryorolling and intermediate aging treatment[J]. Materials Science and Engineering A, 2017, 680: 108-114.
[2]Abib K, Balanos J A M, Alili B, et al. On the microstructure and texture of Cu-Cr-Zr alloy after severe plastic deformation by ECAP[J]. Materials Characterization, 2016, 112: 252-258.
[3]Zhou J M, Zhu D G, Tang L T, et al. Microstructure and properties of powder metallurgy Cu-1%Cr-0.65%Zr alloy prepared by hot pressing[J]. Vacuum, 2016, 131: 156-163.
[4]Sahlot P, Jha K, Dey G K, et al. Quantitative wear analysis of H13 steel tool during friction stir welding of Cu-0.8%Cr-0.1%Zr alloy[J]. Wear, 2017, 378: 82-89.
[5]Zhang Q, Gong W, Wei L I U. Microstructure and mechanical properties of dissimilar Al-Cu joints by friction stir welding[J]. Transactions of Nonferrous Metals Society of China, 2015, 25(6): 1779-1786.
[6]Kanigalpula P, Chatterjee A, Pratihar D, et al. Effects of electron beam welding on microstructure, microhardness, and electrical conductivity of Cu-Cr-Zr alloy plates[J]. Journal of Materials Engineering and Performance, 2015, 24(12): 4681-4690.
[7]Wang Z, Wang G P, Jiang Z J. Microstructure and properties of high strength and conductivity Cu-Cr-Zr alloys by TIG welding[J]. Modern Welding, 2010(9): 85-94.
[8]Akinlabi E T, Sanusi K O, Muzenda E, et al. Material behaviour characterization of friction stir spot welding of copper[J]. Materials Today: Proceedings, 2017, 4(2): 166-177.
[9]He X C, Gu F S, Ball A. A review of numerical analysis of friction stir welding[J]. Progress in Materials Science, 2014, 65: 61-66.
[10]Sauvage X, Dédé A, Muñoz A C, et al. Precipitate stability and recrystallisation in the weld nuggets of friction stir welded Al-Mg-Si and Al-Mg-Sc alloys[J]. Materials Science and Engineering A, 2008, 491: 364-371.
[11]Cavaliere P, Cabibbo M, Panella F, et al. 2198 Al-Li plates joints by friction stir welding: Mechanical and microstructural behavior[J]. Materials and Design, 2009, 30: 3622-3631.
[12]He D Q, Xie M, Lai R L. Microstructure and mechanical properties of friction stir welded joints of Cu-Cr-Zr alloy plates[J]. Hot Working Technology, 2013, 42: 32-34.
[13]Jha K, Kumar S, Nachiket K, et al. Friction stir welding of aged CuCrZr alloy plates[J]. Metallurgical and Materials Transactions, 2018, 49: 223-234.
[14]Lai R L, Li X Q, He D Q, et al. Microstructure evolution and localized properties variation of a thick friction stir welded CuCrZr alloy plate[J]. Journal of Nuclear Materials, 2018, 510: 70-79.
[15]Bernard Y, Renard V T, Conon P, et al. Back-end-of-line compatible conductive bridging RAM based on Cu and SiO₂[J]. Microelectronic Engineering, 2011, 88: 814-816.
[16]Xiao B L, Yang Q, Yang J, et al. Enhanced mechanical properties of Mg-Gd-Y-Zr casting via friction stir processing[J]. Journal of Alloys and Compounds, 2011, 509: 2879-2884.
[17]Gan W Y, Zhou Z, Zhang H, et al. Evolution of microstructure and hardness of aluminum after friction stir processing[J]. Transactions of Nonferrous Metals Society of China, 2014, 24: 975-981.
[18]Hansen N. Polycrystalline strengthening[J]. Metallurgical and Transactions A, 1985, 16: 2167-2190.
[19]Nembach E, Neite G. Precipitation hardening of super alloys by ordered γ′-particles[J]. Progress in Materials Science, 1985, 29: 177-319.
[20]Conrad H, Narayan J. On the grain size softening in nanocrystalline materials[J]. Scripta Materialia, 2000, 42: 1025-1030.
[21]Voyiadjis Z G, Almasri A H. Variable material length scale associated with nanoindentation experiments[J]. Journal of Engineering Mechanics, 2009, 139: 139-148.

Cu-Cr-Zr合金搅拌摩擦焊接接头的组织和力学性能

Microstructure and mechanical properties of friction stir welding joint of Cu-Cr-Zr alloy

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	王玉岱, 刘洋, 朱言言, 田象军, 程序, 冉先喆, 钱婷婷. 热处理对复合制造AerMet100超高强度钢组织均匀性与拉伸性能的影响[J]. 金属热处理, 2022, 47(4): 1-9.
[2]	张子延, 陈君, 陈晓亚, 李全安, 刘建鑫. 固溶时效处理对Mg-4Sm-3Gd-0.5Zr合金显微组织和耐蚀性能的影响[J]. 金属热处理, 2022, 47(4): 10-16.
[3]	梁恩溥, 徐乐, 杨勇, 王毛球. 添加Al、Cu对40CrNi3MoV钢组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 17-23.
[4]	祁晓亮, 李岩, 定巍, 赵增武. 含Al中锰TRIP钢原始组织对临界退火后组织与力学性能的影响[J]. 金属热处理, 2022, 47(4): 24-29.
[5]	陈保安, 张静媛, 祝志祥, 韩钰, 潘学东, 张磊, 陈素红. 化学成分对高强Al-Mg-Si合金组织和性能的影响[J]. 金属热处理, 2022, 47(4): 30-38.
[6]	陈东俊, 李广阳, 刘刚. 时效处理对AlSi9Cu3压铸铝合金组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 53-56.
[7]	陈连生, 张露友, 田亚强, 杨子旋, 李红斌, 潘红波, 魏英立. 低碳高强舰船用钢的CCT曲线及其组织性能[J]. 金属热处理, 2022, 47(4): 63-68.
[8]	贾昌远, 霍元明, 何涛, 霍存龙, 刘克然. 40CrNiMo钢高温拉伸变形行为和组织演变规律[J]. 金属热处理, 2022, 47(4): 69-74.
[9]	王云龙, 余伟, 张昳, 史佳新, 李明辉. 奥氏体化温度对贝氏体钢等温转变及力学性能的影响[J]. 金属热处理, 2022, 47(4): 80-85.
[10]	刘丽艳, 毕文珍, 韦习成. Mn元素对热冲压钢镀锌层组织演变的影响[J]. 金属热处理, 2022, 47(4): 93-99.
[11]	骆再斌, 范子泽, 彭振. 轻质高熵合金的研究进展[J]. 金属热处理, 2022, 47(4): 100-107.
[12]	付锡彬, 陈子豪, 张可, 赵时雨, 孙新军, 朱正海, 梁小凯, 雍岐龙. 淬火温度对高Ti低合金耐磨钢组织及力学性能的影响[J]. 金属热处理, 2022, 47(4): 122-127.
[13]	宿鹏吉, 麻永林, 董丽丽, 杨雪峰. 磁场预退火处理对CGO钢组织与织构的影响[J]. 金属热处理, 2022, 47(4): 128-132.
[14]	李立, 曾艳, 吴晓春. 4Cr5Mo2VCo钢的热处理工艺优化[J]. 金属热处理, 2022, 47(4): 133-140.
[15]	吕杰晟, 宋志刚, 何建国, 丰涵, 郑文杰, 朱玉亮. S32205双相不锈钢冷轧退火组织转变及强塑化机理分析[J]. 金属热处理, 2022, 47(4): 141-145.