喷射成形Al-Zn-Mg-Cu合金挤压态的组织和力学性能

doi:10.13251/j.issn.0254-6051.2020.07.035

金属热处理 ›› 2020, Vol. 45 ›› Issue (7): 173-176.DOI: 10.13251/j.issn.0254-6051.2020.07.035

喷射成形Al-Zn-Mg-Cu合金挤压态的组织和力学性能

潘海成, 陈业高, 孙肖霞, 范钧

宿迁学院机电工程学院, 江苏宿迁 223800

收稿日期:2020-01-26 出版日期:2020-07-25 发布日期:2020-09-07
通讯作者: 陈业高, 讲师, 博士, E-mail:chenyegao0611@163.com
作者简介:潘海成(1987—), 男, 讲师, 硕士, 主要研究方向为材料加工工程方向, E-mail:pmc999@163.com。
基金资助:
宿迁市科技计划(Z2018222,Z2019111);江苏高校品牌专业建设工程资助项目(PPZY2015C252)

Microstructure and mechanical properties of extrusion state Al-Zn-Mg-Cu alloy after spray forming

Pan Haicheng, Chen Yegao, Sun Xiaoxia, Fan Jun

School of Mechanical and Electrical Engineering, Suqian College, Suqian Jiangsu 223800, China

Received:2020-01-26 Online:2020-07-25 Published:2020-09-07

摘要/Abstract

摘要： 研究了利用喷射成形辅以挤压制备Al-5.72Zn-2.36Mg-1.66Cu合金后优化的组织结构特征和力学性能。结果表明,合金基体组织均匀细化,晶粒形貌趋于圆整,平均晶粒大小达到10 μm左右。当合金的冷却条件通过快速凝固技术改变时,会产生不同程度的固溶强化效果和第二相弥散强化效果,从而改善了合金的整体性能。合金的屈服强度和抗拉强度分别平均提高了20%左右,且伸长率也略有提高。

关键词: Al-Zn-Mg-Cu铝合金, 喷射成形, 快速凝固, 组织, 力学性能

Abstract: Optimized microstructure characteristics and the mechanical properties of the Al-5.72Zn-2.36Mg-1.66Cu aluminium alloy prepared by spray forming and continuous extrusion were studied. The results show that the microstructure of the alloy matrix is uniformly refined and the morphology of the grains tends to be rounded. And the average grain size of the alloy is about 10 μm. The different effects of the solid solution strengthening and second-phase dispersion strengthening will be generated when the cooling condition of the alloy is changed by the rapid solidification. Thus,the overall properties of the alloy are also improved by spraying. The yield strength and tensile strength of the alloy are increased by about 20% on average, and the elongation is increased slightly.

Key words: Al-Zn-Mg-Cu aluminum alloy, spray forming, rapid solidification, microstructure, mechanical properties

中图分类号:

TG146.2

潘海成, 陈业高, 孙肖霞, 范钧. 喷射成形Al-Zn-Mg-Cu合金挤压态的组织和力学性能[J]. 金属热处理, 2020, 45(7): 173-176.

Pan Haicheng, Chen Yegao, Sun Xiaoxia, Fan Jun. Microstructure and mechanical properties of extrusion state Al-Zn-Mg-Cu alloy after spray forming[J]. Heat Treatment of Metals, 2020, 45(7): 173-176.

参考文献

[1]王奋翔, 徐国富, 江福清, 等. Zn含量和Zn/Mg比对Al-Zn-Mg-Cu铝合金拉伸性能和淬透性的影响[J]. 金属热处理, 2019, 44(12): 49-53.
Wang Fenxiang, Xu Guofu, Jiang Fuqing, et al. Effects of Zn content and Zn/Mg ratio on tensile properties and hardenability of Al-Zn-Mg-Cu alloy[J]. Heat Treatment of Metals, 2019, 44(12): 49-53.
[2]潘海成. 微合金化铝铁合金的强化机理[J]. 热加工工艺, 2015, 44(21): 82-84.
Pan Haicheng. Strengthening mechanism of micro alloying of Al-Fe alloy[J]. Hot Working Technology, 2015, 44(21): 82-84.
[3]Shivkumar S, Wang L, Apelian D. Molten metal processing of advanced cast aluminum alloys[J]. JOM, 1991(1): 26-29.
[4]刘守法, 周兆锋, 刘丹成. Si添加对粉末冶金AZ80合金组织及高温力学性能的影响[J]. 金属热处理, 2019, 44(11): 30-34.
Liu Shoufa, Zhou Zhaofeng, Liu Dancheng. Effect of Si addition on microstructure and high temperature mechanical properties of powder metallurgy AZ80 alloy[J]. Heat Treatment of Metals, 2019, 44(11): 30-34.
[5]李兆健. 多元合金化发动机用新型铝硅合金组织及性能的研究[D]. 合肥: 合肥工业大学, 2014.
Li Zhaojian. Research on microstructure and properties of new multiple aluminum alloy for engine[D]. Hefei: Hefei University of Technology, 2014.
[6]舒适, 黎兴刚, 刘锡魁, 等. 耦合压力-气体雾化工艺制备微细球形铝合金粉末[J]. 稀有金属, 2019, 43(8): 808-815.
Shu Shi, Li Xinggang, Liu Xikui, et al. Coupled pressure-gas atomization process for fine spherical aluminium alloy powder production[J]. Chinese Journal of Rare Metals, 2019, 43(8): 808-815.
[7]毛帅英. 基于旋凝铝合金带的材料工艺、组织和力学性能的研究[D]. 秦皇岛: 燕山大学, 2015.
Mao Shuaiying. Processing, microstructure and mechanical properties of Al alloys based on melt spun ribbons[D]. Qinhuangdao: Yanshan University, 2015.
[8]郑大亮, 高鹏, 尹建成, 等. 2A12铝合金喷射沉积坯的形状控制及显微组织[J]. 机械工程材料, 2015, 39(8): 22-25.
Zheng Daliang, Gao Peng, Yin Jiancheng, et al. Shape control and microstructure of spray deposited billets of 2A12 aluminum alloy[J]. Materials for Mechanical Engineering, 2015, 39(8): 22-25.
[9]侯兆阳, 刘丽霞, 刘让苏, 等. Al-Mg合金熔体快速凝固过程中微观结构演化机理的模拟研究[J]. 物理学报, 2009, 58(7): 4817-4825.
Hou Zhaoyang, Liu Lixia, Liu Rangsu, et al. Simulation of evolution mechanisms of microstructures during rapid solidification of Al-Mg alloy melt[J]. Acta Physica Sinica, 2009, 58(7): 4817-4825.
[10]Chen Y G, Yi Z, Yin J C, et al. Spray conform 7075 Al[J]. Rsc Advances, 2015, 118(5): 97612-97618.
[11]王艳娟, 胡晓青, 曲庆文, 等. RRA处理对7085铝合金微观组织演变及性能的影响[J]. 金属热处理, 2019, 44(8): 45-49.
Wang Yanjuan, Hu Xiaoqing, Qu Qingwen, et al. Influence of RRA treatment on microstructure evolution and properties of 7085 aluminum alloy[J]. Heat Treatment of Metals, 2019, 44(8): 45-49.
[12]贺毅强, 徐政坤, 陈振华. 快速凝固Al-Fe系耐热铝合金的研究进展[J]. 材料科学与工程学报, 2011, 29(4): 633-638.
He Yiqiang, Xu Zhengkun, Chen Zhenhua. Progress in Al-Fe heat resistant alloys prepared by rapid solidification[J]. Journal of Materials Science and Engineering, 2011, 29(4): 633-638.
[13]王敬丰, 魏怡芸, 吴夏, 等. 铸态、挤压态和快速凝固态ZK60镁合金微观组织及压缩性能[J]. 材料工程, 2011(8): 32-35.
Wang Jingfeng, Wei Yiyun, Wu Xia, et al. Microstructure and compression properties of as-cast, as-extruded and rapid solidified ZK60 magnesium alloy[J]. Journal of Materials Engineering, 2011(8): 32-35.
[14]杨文朋, 郭学锋. 往复挤压快速凝固ZK60合金的组织与力学性能[J]. 金属热处理, 2011, 36(7): 5-9.
Yang Wenpeng, Guo Xuefeng. Microstructure and mechanical properties of ZK60 alloy processed by rapid solidification and reciprocating extrusion[J]. Heat Treatment of Metals, 2011, 36(7): 5-9.

[1]	王玉岱, 刘洋, 朱言言, 田象军, 程序, 冉先喆, 钱婷婷. 热处理对复合制造AerMet100超高强度钢组织均匀性与拉伸性能的影响[J]. 金属热处理, 2022, 47(4): 1-9.
[2]	张子延, 陈君, 陈晓亚, 李全安, 刘建鑫. 固溶时效处理对Mg-4Sm-3Gd-0.5Zr合金显微组织和耐蚀性能的影响[J]. 金属热处理, 2022, 47(4): 10-16.
[3]	梁恩溥, 徐乐, 杨勇, 王毛球. 添加Al、Cu对40CrNi3MoV钢组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 17-23.
[4]	祁晓亮, 李岩, 定巍, 赵增武. 含Al中锰TRIP钢原始组织对临界退火后组织与力学性能的影响[J]. 金属热处理, 2022, 47(4): 24-29.
[5]	陈保安, 张静媛, 祝志祥, 韩钰, 潘学东, 张磊, 陈素红. 化学成分对高强Al-Mg-Si合金组织和性能的影响[J]. 金属热处理, 2022, 47(4): 30-38.
[6]	陈东俊, 李广阳, 刘刚. 时效处理对AlSi9Cu3压铸铝合金组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 53-56.
[7]	陈连生, 张露友, 田亚强, 杨子旋, 李红斌, 潘红波, 魏英立. 低碳高强舰船用钢的CCT曲线及其组织性能[J]. 金属热处理, 2022, 47(4): 63-68.
[8]	贾昌远, 霍元明, 何涛, 霍存龙, 刘克然. 40CrNiMo钢高温拉伸变形行为和组织演变规律[J]. 金属热处理, 2022, 47(4): 69-74.
[9]	王云龙, 余伟, 张昳, 史佳新, 李明辉. 奥氏体化温度对贝氏体钢等温转变及力学性能的影响[J]. 金属热处理, 2022, 47(4): 80-85.
[10]	刘丽艳, 毕文珍, 韦习成. Mn元素对热冲压钢镀锌层组织演变的影响[J]. 金属热处理, 2022, 47(4): 93-99.
[11]	骆再斌, 范子泽, 彭振. 轻质高熵合金的研究进展[J]. 金属热处理, 2022, 47(4): 100-107.
[12]	付锡彬, 陈子豪, 张可, 赵时雨, 孙新军, 朱正海, 梁小凯, 雍岐龙. 淬火温度对高Ti低合金耐磨钢组织及力学性能的影响[J]. 金属热处理, 2022, 47(4): 122-127.
[13]	宿鹏吉, 麻永林, 董丽丽, 杨雪峰. 磁场预退火处理对CGO钢组织与织构的影响[J]. 金属热处理, 2022, 47(4): 128-132.
[14]	李立, 曾艳, 吴晓春. 4Cr5Mo2VCo钢的热处理工艺优化[J]. 金属热处理, 2022, 47(4): 133-140.
[15]	吕杰晟, 宋志刚, 何建国, 丰涵, 郑文杰, 朱玉亮. S32205双相不锈钢冷轧退火组织转变及强塑化机理分析[J]. 金属热处理, 2022, 47(4): 141-145.

喷射成形Al-Zn-Mg-Cu合金挤压态的组织和力学性能

Microstructure and mechanical properties of extrusion state Al-Zn-Mg-Cu alloy after spray forming

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价