碳含量对4Cr5Mo2V型热作模具钢冷热疲劳性能的影响

doi:10.13251/j.issn.0254-6051.2020.11.001

金属热处理 ›› 2020, Vol. 45 ›› Issue (11): 1-6.DOI: 10.13251/j.issn.0254-6051.2020.11.001

• 材料研究 • 下一篇

碳含量对4Cr5Mo2V型热作模具钢冷热疲劳性能的影响

殷军伟^1,2, 周健², 蒋业华¹, 迟宏宵², 林鹏²

1.昆明理工大学材料科学与工程学院, 云南昆明 650093;
2.钢铁研究总院特殊钢研究所, 北京 100081

收稿日期:2020-04-15 出版日期:2020-11-25 发布日期:2020-12-29
通讯作者: 周健,高级工程师,博士,E-mail:zhou-jian-168@163.com
作者简介:殷军伟(1989—),男,硕士,主要研究方向为工、模具钢的研制和开发,E-mail:610631308@qq.com。

Effect of carbon content on thermal fatigue properties of 4Cr5Mo2V hot work die steel

Yin Junwei^1,2, Zhou Jian², Jiang Yehua¹, Chi Hongxiao², Lin Peng²

1. Faculty of Materials Science and Engineering, Kunming University of Science and Technology, Kunming Yunnan 650093, China;
2. Special Steels Research Institute, Central Iron & Steel Research Institute, Beijing 100081, China

Received:2020-04-15 Online:2020-11-25 Published:2020-12-29

摘要/Abstract

摘要： 采用自约束热疲劳试验法,结合SEM、EDS以及Jmat-pro热力学计算软件等研究了碳含量(0.35%和0.71%)变化对4Cr5Mo2V型热作模具钢冷热疲劳性能的影响。结果表明:提高含碳量后,钢中析出大量细小弥散的MC型碳化物,从而使0.71%C钢的抗回火软化性能和热稳定性能均强于0.35%C钢;冷热疲劳循环1000次后,提高碳含量推迟了疲劳裂纹的萌生,当循环次数增加到2000次后,虽然0.71%C钢表面和基体的软化程度均弱于0.35%C钢,但该钢存在较多尺寸较大且呈聚集状态分布的未溶碳化物,这些碳化物在应力的作用下与基体脱离,脱离处成为裂纹扩展的通道,从而促进了疲劳裂纹萌生和扩展。

关键词: 碳含量, 4Cr5Mo2V热作模具钢, 抗回火软化性能, 热稳定性能, 冷热疲劳性能

Abstract: With self-constrained thermal fatigue test method, the effect of carbon content(0.35% and 0.71%) on the thermal fatigue properties of 4Cr5Mo2V hot work die steel was studied by SEM, EDS and Jmat-pro thermodynamic calculation software. The results show that with the increase of carbon content, a large amount of finely dispersed MC-type carbides are precipitated in the steel, so that the temper softening resistance and thermal stability of the 0.71%C steel are better than those of the 0.35%C steel. After 1000 cycles of thermal fatigue, increasing the carbon content delays the initiation of thermal fatigue cracks. When the number of cycles increases to 2000, although the softening of the surface and matrix of 0.71%C steel is weaker than that of 0.35%C steel, but there are many undissolved carbides with large size and obvious aggregation distribution in the 0.71%C steel. These carbides are detached from the matrix under the effect of stress, and the detached places become channels for crack propagation, thereby promoting the initiation and propagation of fatigue cracks.

Key words: carbon content, 4Cr5Mo2V hot work die steel, temper softening resistance, thermal stability, thermal fatigue properties

中图分类号:

殷军伟, 周健, 蒋业华, 迟宏宵, 林鹏. 碳含量对4Cr5Mo2V型热作模具钢冷热疲劳性能的影响[J]. 金属热处理, 2020, 45(11): 1-6.

Yin Junwei, Zhou Jian, Jiang Yehua, Chi Hongxiao, Lin Peng. Effect of carbon content on thermal fatigue properties of 4Cr5Mo2V hot work die steel[J]. Heat Treatment of Metals, 2020, 45(11): 1-6.

参考文献

[1]Melloulia D, Haddar N, Köster A, et al. Hardness effect on thermal fatigue damage of hot-working tool steel[J]. Engineering Failure Analysis, 2014, 45: 85-95.
[2]闵娜, 石楠楠, 沈赟靓, 等. 马氏体热作模具钢热稳定性的内耗研究[J]. 材料热处理学报, 2012, 33(2): 96-99.
Min Na, Shi Nannan, Shen Yunliang, et al. Internal friction investigation on thermal-stability of martensitic hot work tool steel[J]. Transactions of Materials and Heat Treatment, 2012, 33(2): 96-99.
[3]Lu Y, Ripplingerb K, Huang X J, et al. A new fatigue life model for thermally-induced cracking in H13 steel dies for die casting[J]. Journal of Materials Processing Technology, 2019, 271: 444-454.
[4]夏鹏成, 陈蕴博, 葛学元, 等. 热作模具钢热疲劳性能的研究现状与发展趋势[J]. 金属热处理, 2008, 33(12): 1-5.
Xia Pengcheng, Chen Yunbo, Ge Xueyuan, et al. Research status and development trends of thermal fatigue property of hot die steels[J]. Heat Treatment of Metals, 2008, 33(12): 1-5.
[5]胡心彬, 李麟, 吴晓春. 含铌H13钢热疲劳过程中的显微结构变化[J]. 金属热处理, 2005, 30(3): 27-30.
Hu Xinbin, Li Lin, Wu Xiaochun. Microstructure changes of H13 hot work tool steel with niobium during thermal fatigue[J]. Heat Treatment of Metals, 2005, 30(3): 27-30.
[6]Sherman A M, Davies R G. The effect of martensite content on the fatigue of a dual-phase steel[J]. International Journal of Fatigue, 1981, 3(1): 36-40.
[7]周青春. 硅在H13型热作模具钢中作用的研究[D]. 上海: 上海大学, 2012: 121-150.
Zhou Qingchun. Effect of silicon on H13 type hot work die steel[D]. Shanghai: Shanghai University, 2012: 121-150.
[8]丁柏群, 曹贵允. 60CrMnMoRE钢热疲劳性能研究[J]. 钢铁, 1999, 30(2): 38-42.
Ding Baiqun, Cao Guiyun. Study on thermal-fatigue property of steel 60CrMnMoRE[J]. Iron and Steel, 1999, 30(2): 38-42.
[9]张学友, 左鹏鹏, 吴晓春. 氮含量对热作模具钢4Cr5Mo2V热疲劳性能的影响[J]. 金属热处理, 2017, 42(1): 9-14.
Zhang Xueyou, Zuo Pengpeng, Wu Xiaochun. Effect of nitrogen content on thermal fatigue property of hot work die steel 4Cr5Mo2V[J]. Heat Treatment of Metals, 2017, 42(1): 9-14.
[10]李爽, 吴晓春, 黎欣欣, 等. 钼钨系高导热率热作模具钢高温性能[J]. 材料研究学报, 2017, 31(1): 32-39.
Li Shuang, Wu Xiaochun, Li Xinxin, et al. High temperature performance of a Mo-W type hot work die steel of high thermal conductivity[J]. Chinese Journal of Materials Research, 2017, 31(1): 32-39.
[11]Park J H, Kweon Y G, Kim H J, et al. The Effects of alloying elements on thermal fatigue and thermal shock resistance of the HSLA cast steels[J]. ISIJ International, 2000, 40(11): 1164-1169.
[12]许书洋, 左鹏鹏, 吴晓春. 硬度对 H13 热作模具钢热疲劳性能的影响[J]. 金属热处理, 2016, 41(8): 18-23.
Xu Shuyang, Zuo Pengpeng, Wu Xiaochun. Effect of hardness on thermal fatigue of H13 hot work die steel[J]. Heat Treatment of Metals, 2016, 41(8): 18-23.
[13]隋鹤龙. 新型高Cr热作模具钢的组织与性能[D]. 长春: 吉林大学, 2006.
Sui Helong. Microstructures and properties of new type high-Cr hot working die steel[D]. Changchun: Jilin University, 2006.

碳含量对4Cr5Mo2V型热作模具钢冷热疲劳性能的影响

Effect of carbon content on thermal fatigue properties of 4Cr5Mo2V hot work die steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 9

编辑推荐

Metrics

本文评价

[1]	张明桥, 傅明娇, 赵晓光, 付朝政, 汪洪宇, 李卓林. 碳含量对SA-508 Gr.3钢大锻件组织和性能的影响[J]. 金属热处理, 2021, 46(7): 79-83.
[2]	常永, 李立, 吴少君, 左鹏鹏, 吴晓春. 球化温度对4Cr5Mo2V热作模具钢组织和性能的影响[J]. 金属热处理, 2021, 46(3): 46-50.
[3]	郑业方, 姜影, 谢小军, 夏玉亮, 李泉, 游菲. 热处理对铬钼钢刀具畸变的影响[J]. 金属热处理, 2021, 46(3): 113-115.
[4]	刘哲, 丰涵, 郑文杰, 宋志刚, 朱玉亮, 高鹏. 镍基690合金的晶粒控制及其对力学性能的影响[J]. 金属热处理, 2020, 45(1): 203-209.
[5]	闫永明. 冷却方式对23CrNi3Mo渗碳钢组织结构的影响[J]. 金属热处理, 2016, 41(7): 134-138.
[6]	纪显彬，李具仓，王建泽，钱张信. Cr13马氏体不锈钢热处理显微组织和硬度[J]. 金属热处理, 2016, 41(6): 93-96.
[7]	蔡媛媛1，左鹏鹏1，朱春燕1，闵娜2，吴晓春1. 三种热锻模具钢热稳定性能对比研究[J]. 金属热处理, 2016, 41(5): 34-39.
[8]	丁盛，马良，许仁伟，黄星，顾晓明. 硝基浴淬火烈度的计算及分析[J]. 金属热处理, 2016, 41(4): 133-136.
[9]	邓红星1,2，郑文杰2，宋志刚2，岑启宏1，丰涵2. 碳含量对0Cr25Ni35AlTi合金组织、力学性能和耐晶间腐蚀性能的影响[J]. 金属热处理, 2015, 40(10): 13-17.