热等静压处理对K439B高温合金显微组织的影响

doi:10.13251/j.issn.0254-6051.2020.11.033

金属热处理 ›› 2020, Vol. 45 ›› Issue (11): 177-181.DOI: 10.13251/j.issn.0254-6051.2020.11.033

热等静压处理对K439B高温合金显微组织的影响

张明军¹, 张雷雷^1,2, 胡颖涛³, 汤鑫¹, 杨卿²

1.北京航空材料研究院先进高温结构材料重点实验室, 北京 100095;
2.西安理工大学材料科学与工程学院, 陕西西安 710048;
3.中国航发西安航空发动机有限公司铸造厂, 陕西西安 710021

收稿日期:2020-04-30 出版日期:2020-11-25 发布日期:2020-12-29
作者简介:张明军(1982—),男,高级工程师,硕士,主要研究方向为高温合金精密铸造,E-mail:zhangmingjun621@126.com
基金资助:
中国航空发动机集团自主创新专项资金(CXPT-2018-006);中国航空发动机集团产学研合作项目(HFZL2018CXY022);国家两机重大专项(2017-VII-0008-0102)

Effect of hot isostatic pressing on microstructure of K439B superalloy

Zhang Mingjun¹, Zhang Leilei^1,2, Hu Yingtao³, Tang Xin¹, Yang Qing²

1. Science and Technology on Advanced High Temperature Structural Materials Laboratory, Beijing Institute of Aeronautical Materials, Beijing 100095, China;
2. Faculty of Materials Science and Engineering, Xi'an University of Technology, Xi'an Shaanxi 710048, China;
3. Precision Investment Casting, AECC Xi'an Aero-engine Ltd., Xi'an Shaanxi 710021, China

Received:2020-04-30 Online:2020-11-25 Published:2020-12-29

摘要/Abstract

摘要： 对K439B合金进行了1165 ℃/150 MPa,4 h热等静压处理,采用光学显微镜和扫描电镜对比研究了铸态和热等静压态K439B合金的显微组织。结果表明:铸态K439B合金存在0.25%的显微疏松,热等静压后显微疏松基本消除(0.013%)。与铸态相比,经过热等静压处理后合金中的γ/γ′共晶组织体积分数和尺寸减小,各元素分布更加均匀,凝固偏析系数均更接近1。铸态K439B合金枝晶干处γ′相尺寸和体积分数分别是116.9 nm和17.8%,枝晶间部位γ′相尺寸和体积分数分别为244.4 nm和24.9%。热等静压后合金枝晶干部位的γ′相尺寸及体积分数分别为148.0 nm和17.5%,枝晶间部位γ′相尺寸和体积分数分别为159.1 nm和22.8%。热等静压处理使合金枝晶干、枝晶间部位的γ′相尺寸、体积分数和形貌接近,同时γ′相分布变得均匀。

关键词: K439B高温合金, 热等静压, 显微组织, 显微疏松, γ/γ′共晶组织

Abstract: K439B superalloy was hot isostatic pressed (HIP) under 1165 ℃/150 MPa for 4 h, then the microstructure of as-cast and hot isostatic pressed K439B alloy was investigated comparatively by using OM and SEM. The results show that the as-cast K439B alloy has microporosity of 0.25%, which is reduced down to only 0.013% after HIP. Compared with the as-cast microstructure, after HIP both the content and the size of γ/γ′ eutectic decrease, and all the elements are distributed more evenly, with their solidification segregation coefficients being closer to 1. The size and volume fraction of γ′ precipitates in the dendritic arms of as-cast K439B alloy are 116.9 nm and 17.8% respectively, and that in interdendritic region are 244.4 nm and 24.9%. After HIP, the size and volume fraction of γ′ precipitates in the dendritic arms are 148.0 nm and 17.5% respectively, and that in the interdendritic region are 159.1 nm and 22.8%. The hot isostatic pressing makes that the size, volume fraction and morphology of γ′ precipitates in the dendritic arms in the alloy and that in the interdendritic region become more similar to each other, and the γ′ precipitates distribute more uniformly.

Key words: K439B superalloy, hot isostatic pressing, microstructure, microporosity, γ/γ′ eutectic

中图分类号:

TG132.3⁺2

张明军, 张雷雷, 胡颖涛, 汤鑫, 杨卿. 热等静压处理对K439B高温合金显微组织的影响[J]. 金属热处理, 2020, 45(11): 177-181.

Zhang Mingjun, Zhang Leilei, Hu Yingtao, Tang Xin, Yang Qing. Effect of hot isostatic pressing on microstructure of K439B superalloy[J]. Heat Treatment of Metals, 2020, 45(11): 177-181.

参考文献

[1]Pollock T M. Alloy design for aircraft engines[J]. Nature Materials, 2016, 15(8): 809-815.
[2]Singh K. Advanced materials for land based gas turbines[J]. Transactions of the Indian Institute of Metals, 2014, 67(5): 601-615.
[3]张健, 楼琅洪. 铸造高温合金研发中的应用基础研究[J]. 金属学报, 2018, 54(11): 1637-1652.
Zhang Jian, Lou Langhong. Basic research in development and application of cast superalloy[J]. Acta Metallurgica Sinica, 2018, 54(11): 1637-1652.
[4]陈晶阳, 吴文津, 李青, 等. 采用低温度梯度HRS工艺制备的镍基单晶高温合金雀斑组织[J]. 中国有色金属学报, 2018, 28(12): 2494-2498.
Chen Jingyang, Wu Wenjin, Li Qing, et al. Freckle of Ni-based single crystal superalloy prepared by low thermal gradient HRS process[J]. The Chinese Journal of Nonferrous Metals, 2018, 28(12): 2494-2498.
[5]陈晶阳, 李青, 肖程波, 等. 第二代耐热腐蚀镍基单晶高温合金DD489及其典型性能[J]. 金属热处理, 2019, 44(6): 65-68.
Chen Jingyang, Li Qing, Xiao Chengbo, et al. The second generation hot corrosion resistant Ni-based single crystal superalloy DD489 and its typical properties[J]. Heat Treatment of Metals, 2019, 44(6): 65-68.
[6]孙宝德, 王俊, 疏达. 航空发动机高温合金大型铸件精密成型技术[M]. 上海: 上海交通大学出版社, 2016: 1-5.
Sun Baode, Wang Jun, Shu Da. Precision Forming Technology of Large Superalloy Castings for Aircraft Engine[M]. Shanghai: Shanghai Jiao Tong University Press, 2016: 1-5.
[7]张善勇, 隋玉俭. 铸造高温合金的热等静压致密化机理[J]. 钢铁研究总院学报, 1985, 5(S1): 77-83.
Zhang Shanyong, Sui Yujian. HIP densification mechanisms for cast superalloys[J]. Central Iron and Steel Research Institute Technical Bulletin, 1985, 5(S1): 77-83.
[8]Li J, Yuan C, Guo J, et al. Effect of hot isostatic pressing on microstructure of cast gas-turbine vanes of K452 alloy[J]. Progress in Natural Science: Materials International, 2014, 24(6): 631-636.
[9]何树先, 王俊, 孙宝德. 热等静压对高温合金薄壁铸件疏松缺陷及性能的影响[J]. 热加工工艺, 2014, 43(21): 88-90.
He Shuxian, Wang Jun, Sun Baode. Influence of HIP treatment on microporosity and properties of thin wall superalloy casting[J]. Hot Working Technology, 2014, 43(21): 88-90.
[10]王伟, 李强, 杨维才, 等. 镍基铸造高温合金的热等静压改性研究[J]. 金属热处理, 2014, 39(1): 85-88.
Wang Wei, Li Qiang, Yang Weicai, et al. Modification of cast nickel-base superalloy by hot isostatic pressing[J]. Heat Treatment of Metals, 2014, 39(1): 85-88.
[11]呼和. 镍基铸造高温合金的热等静压处理[J]. 金属学报, 2002, 38(11): 1199-1202.
Hu He. Hot isostatic pressing treatment of cast Ni-base superalloy[J]. Acta Metallurgica Sinica, 2002, 38(11): 1199-1202.
[12]Liu L J, Xue M, Chen J Y, et al. Effect of hot isostatic pressing on the microstructure of single crystal Ni-based superalloy DD10[J]. Materials Science Forum, 2013, 747-748: 772-776.
[13]Whitmore L, Ahmadi M R, Guetaz L, et al. The microstructure of heat-treated nickel-based superalloy 718Plus[J]. Materials Science and Engineering A, 2014, 610: 39-45.
[14]Cao G H, Sun T Y, Wang C H, et al. Investigations of γ′, γ″ and δ precipitates in heat-treated Inconel 718 alloy fabricated by selective laser melting[J]. Materials Characterization, 2018, 136: 398-406.
[15]张雷雷, 陈晶阳, 骞磊, 等. 浇注温度对K439B合金显微组织和力学性能的影响[J]. 材料热处理学报, 2019, 40(9): 57-63.
Zhang Leilei, Chen Jingyang, Qian Lei, et al. Effect of casting temperature on microstructure and mechanical properties of K439B superalloy[J]. Transactions of Materials and Heat Treatment, 2019, 40(9): 57-63.
[16]于军伟, 康茂东, 刘雅辉, 等. 镍基单晶高温合金微观孔洞缺陷研究进展[J]. 铸造技术, 2018, 39(11): 2615-2619.
Yu Junwei, Kang Maodong, Liu Yahui, et al. Advances on micro-pore defect of single-crystal nickel-base superalloy[J]. Foundry Technology, 2018, 39(11): 2615-2619.
[17]李爱兰, 汤鑫, 曹腊梅, 等. 热等静压温度对K447A高温合金显微组织及性能的影响[J]. 航空材料学报, 2012, 32(2): 13-19.
Li Ailan, Tang Xin, Cao Lamei, et al. Effects of HIP temperature on microstructure and mechanical properties of K447A superalloy[J]. Journal of Aeronautical Materials, 2012, 32(2): 13-19.

热等静压处理对K439B高温合金显微组织的影响

Effect of hot isostatic pressing on microstructure of K439B superalloy

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	张子延, 陈君, 陈晓亚, 李全安, 刘建鑫. 固溶时效处理对Mg-4Sm-3Gd-0.5Zr合金显微组织和耐蚀性能的影响[J]. 金属热处理, 2022, 47(4): 10-16.
[2]	梁恩溥, 徐乐, 杨勇, 王毛球. 添加Al、Cu对40CrNi3MoV钢组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 17-23.
[3]	陈连生, 张露友, 田亚强, 杨子旋, 李红斌, 潘红波, 魏英立. 低碳高强舰船用钢的CCT曲线及其组织性能[J]. 金属热处理, 2022, 47(4): 63-68.
[4]	王琪, 吴光亮. 回火温度对1100 MPa级高强钢组织与性能的影响[J]. 金属热处理, 2022, 47(4): 146-150.
[5]	孙凯, 陈研, 杨绍斌. 时效温度对激光选区熔化TC21钛合金微观组织及硬度的影响[J]. 金属热处理, 2022, 47(4): 155-158.
[6]	刘文彬, 乔龙阳, 潘新宇, 程格, 李爱娜, 裴新军. 淬火温度对刀剪用M390粉末冶金不锈钢组织和性能的影响[J]. 金属热处理, 2022, 47(4): 189-195.
[7]	王瑞琴, 葛鹏, 廖强, 侯鹏, 刘宇. 固溶冷却方式对短时用高温钛合金板材组织和性能的影响[J]. 金属热处理, 2022, 47(4): 196-198.
[8]	王绍灼, 孟晗, 王芬, 樊海卫, 李燕, 唐超. 改善低氧TC4-LC及重熔TC4钛合金性能的热处理工艺[J]. 金属热处理, 2022, 47(4): 204-207.
[9]	张宁, 高星, 王芝林, 蒋波, 刘雅政. 18CrNiMo7-6钢齿轮组织性能异常分析[J]. 金属热处理, 2022, 47(4): 268-273.
[10]	王敬元, 吴松全, 张博华, 辛社伟, 杨义, 王皞, 黄爱军. 固溶时效处理对BT25y钛合金显微组织及硬度的影响[J]. 金属热处理, 2022, 47(3): 14-19.
[11]	孙建, 黄贞益, 李景辉, 王萍. 固溶和时效处理对Fe-Mn-Al-C轻质钢组织和硬度的影响[J]. 金属热处理, 2022, 47(3): 34-38.
[12]	王方军, 刘应龙, 时瑶, 万红, 刘斌斌. 等温退火处理对Inconel 625合金箔材组织和性能的影响[J]. 金属热处理, 2022, 47(3): 77-81.
[13]	张曼雪, 景然, 张雄, 张晴, 吴倩, 刘以柔. 铸态Ti-20Zr-10Nb-xMo合金的微观组织和耐腐蚀性能[J]. 金属热处理, 2022, 47(3): 147-150.
[14]	宁静, 高坤元, 李浩楠, 文胜平, 黄晖, 吴晓蓝, 魏午, 聂祚仁. 成分和冷却速度对Al-xEr合金凝固组织的影响[J]. 金属热处理, 2022, 47(3): 151-154.
[15]	王荣, 龚玉辉, 殷学俊, 魏德强. 多道电子束扫描搭接率对40Cr钢组织与性能的影响[J]. 金属热处理, 2022, 47(3): 191-197.