采用正交试验优化Cu-Ni-Sn合金的热处理工艺

doi:10.13251/j.issn.0254-6051.2021.03.012

金属热处理 ›› 2021, Vol. 46 ›› Issue (3): 61-66.DOI: 10.13251/j.issn.0254-6051.2021.03.012

采用正交试验优化Cu-Ni-Sn合金的热处理工艺

李健, 冯再新, 左森, 姚宇康, 郭小森

中北大学材料科学与工程学院, 山西太原 030051

收稿日期:2020-09-01 出版日期:2021-03-25 发布日期:2021-05-08
通讯作者: 冯再新,教授,博士,E-mail:fengzaixin@nuc.edu.cn
作者简介:李健(1994—),男,硕士研究生,主要研究方向为金属材料组织性能,E-mail:1938757290@qq.com。

Optimum heat treatment process of Cu-Ni-Sn alloy by orthogonal test

Li Jian, Feng Zaixin, Zuo Sen, Yao Yukang, Guo Xiaosen

School of Materials Science and Engineering, North University of China, Taiyuan Shanxi 030051, China

Received:2020-09-01 Online:2021-03-25 Published:2021-05-08

摘要/Abstract

摘要： 采用正交试验研究了预变形量和时效处理对新配比Cu-Ni-Sn合金(固溶态Cu-Ni-Sn合金)的力学性能的影响,并使用正交极差分析法得出最佳工艺参数。结果表明,影响Cu-Ni-Sn合金硬度的变化因素为时效温度＞预变形量＞时效时间;影响合金抗拉强度的变化因素为预变形量＞时效时间＞时效温度;影响合金断后伸长率的变化因素为时效温度>冷变形量>时效时间。由此确定最佳的工艺为时效温度360 ℃,时效时间5 h,预变形量40%。随着时效温度和预变形量的增加,合金拉伸断口形貌由大量韧窝的韧性断裂转变为河流状形貌准解理断裂,再到冰糖状沿晶脆性断裂,表明合金塑性逐渐下降。

关键词: Cu-Ni-Sn合金, 正交试验, 力学性能, 热处理工艺

Abstract: Effect of pre-deformation and aging processes on mechanical properties of a new Cu-Ni-Sn alloy (in solid solution state) were studied by using orthogonal test, and the optimum process parameters were obtained by orthogonal range analysis. The results show that the factors affecting the hardness of the Cu-Ni-Sn alloy are: aging temperature>pre-deformation amount>aging time, the factors affecting the tensile strength of the alloy are: pre-deformation amount>aging time>aging temperature, and the factors affecting the percentage elongation after fracture of the alloy are: aging temperature>pre-deformation amount>aging time. Therefore, the optimum process is determined as: aging temperature 360 ℃, aging time 5 h and pre-deformation amount 40%. In addition, with the increase of aging temperature and pre-deformation, the tensile fracture morphologies of the alloy changes from ductile fracture with a large number of dimples to quasi-cleavage fracture with river-like morphologies, and then to intergranular brittle fracture, indicating that the plasticity of the alloy gradually decreases.

Key words: Cu-Ni-Sn alloy, orthogonal test, mechanical properties, heat treatment process

中图分类号:

TG156.92

李健, 冯再新, 左森, 姚宇康, 郭小森. 采用正交试验优化Cu-Ni-Sn合金的热处理工艺[J]. 金属热处理, 2021, 46(3): 61-66.

Li Jian, Feng Zaixin, Zuo Sen, Yao Yukang, Guo Xiaosen. Optimum heat treatment process of Cu-Ni-Sn alloy by orthogonal test[J]. Heat Treatment of Metals, 2021, 46(3): 61-66.

参考文献

[1] Plewes J T.High-strength Cu-Ni-Sn alloys by thermomechanical processing[J].Metallurgical and Materials Transactions A,1975,6(3):537-544.
[2] Zhao J C,Notis M R.Microstructure and precipitation kinetics in a Cu-7.5Ni-5Sn alloy[J].Scripta Materialia,1998,39(11):1509-1516.
[3] Sadi F,Servant C.Phase transformations and phase diagram at equilibrium in the Cu-Ni-Sn system[J].Journal of Thermal Analysis and Calorimetry,2007,90(2):319-323.
[4] Hermann P,Morris D G.Relationship between microstructure and mechanical properties of a spinodally decomposing Cu-15Ni-8Sn alloy prepared by spray deposition[J].Metallurgical and Materials Transactions A,1994,25(7):1403-1412.
[5] Singh J B,Cai W,Bellon P.Dry sliding of Cu-15wt%Ni-8wt%Sn bronze:Wear behaviour and microstructures[J].Wear,2007,263(1):830-841.
[6] 王军,殷俊林,严彪.Cu-Ni-Sn合金的发展和应用[J].上海有色金属,2004(4):184-187.
Wang Jun,Yin Junlin,Yan Biao.Development andapplications of Cu-Ni-Sn alloy[J].Shanghai Nonferrous Metals,2004(4):184-187.
[7] Roh D G,Kang H S,Baik K H.Microstructural feature and aging characteristics of spray-formed Cu-5Ni-10Sn alloy[J].Journal of Korean Powder Metallurgy Institute,2012,19(4):317-321.
[8] 雷静果,井晓天,郅晓.基于连铸连轧法生产固溶态多元铜合金线杆的探讨[J].金属热处理,2005,30(s1):221-222.
Lei Jingguo,Jing Xiaotian,Zhi Xiao.On manufacturing solution polybasic copper alloys rod &wires by continuous casting and rolling process [J].Heat Treatment of Metals,2005,30(s1):221-222.
[9] 范俊玲,曹军,郑磊.热处理对大变形冷加工Cu-0.4Co-0.2Ni-0.2Sn铜合金性能的影响[J].金属热处理,2019,44(8):165-168.
Fan Junling,Cao Jun,Zheng Lei.Effect of heat treatment on properties of large deformation cold worked Cu-0.4Co-0.2Ni-0.2Sn copper alloy [J].Heat Treatment of Metals,2019,44(8):165-168.
[10] Sahu P,Pradhan S K,De M.X-ray diffraction studies of the decomposition and microstructural characterization of cold-worked powders of Cu-15Ni-Sn alloys by Rietveld analysis[J].Journal of Alloys and Compounds,2004,377(1/2):103-116.
[11] Zhao J C,Notis M R.Spinodal decomposition,ordering transformation,and discontinuous precipitation in a Cu-15Ni-8Sn alloy[J].Acta Materialia,1998,46(12):4203-4218.
[12] Du Sanming,Wang Xiaochao,Li Zhen,et al.Effect of Ni content on microstructure and characterization of Cu-Ni-Sn Alloys[J].Materials,2018,11(7):Doi:10.3390/mal1071108.
[13] 范俊玲,郑磊.热处理对Cu-0.4Co-0.2Ni-0.2Sn铜合金组织与性能的影响[J].金属热处理,2019,44(9):173-176.
Fan Junling,Zheng Lei.Effect of heat treatment on Microstructure and properties of Cu-0.4Co-0.2Ni-0.2Sn copper alloy [J].Heat Treatment of Metals,2019,44(9):173-176.
[14] 佘恺,孙梦龙,吴从跃,等.新型CuNiCrSiZr合金的热处理工艺[J].金属热处理,2014,39(7):102-107.
She Kai,sun Menglong,Wu congyue,et al.Heat treatment process of new CuNiCrSiZr alloy [J].Heat Treatment of Metals,2014,39(7):102-107.
[15] 徐恒钧.材料科学基础[M].北京:北京工业大学出版社,2001.
[16] 从善海,韩芳,汪旭超.超高强Cu-Ni-Sn合金的热处理工艺与组织性能[J].金属热处理,2010,35(6):43-47.
Cong Shanhai,Han Fang,Wang Xuchao.Heat treatment processes,microstructure and properties of super high strength Cu-Ni-Sn alloy[J].Heat Treatment of Metals,2010,35(6):43-47.
[17] 肖翔鹏.新型高性能Cu-Ni-Co-Si合金制备及组织性能的研究[D].北京:北京有色金属研究总院,2013.
Xiao Xiangpeng.Research on fabrication,microstructure and properties of Cu-Ni-Co-Si alloy with high performance[D].Beijing:General Research Institute for Nonferrous Metals,2013.

采用正交试验优化Cu-Ni-Sn合金的热处理工艺

Optimum heat treatment process of Cu-Ni-Sn alloy by orthogonal test

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	梁恩溥, 徐乐, 杨勇, 王毛球. 添加Al、Cu对40CrNi3MoV钢组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 17-23.
[2]	祁晓亮, 李岩, 定巍, 赵增武. 含Al中锰TRIP钢原始组织对临界退火后组织与力学性能的影响[J]. 金属热处理, 2022, 47(4): 24-29.
[3]	陈保安, 张静媛, 祝志祥, 韩钰, 潘学东, 张磊, 陈素红. 化学成分对高强Al-Mg-Si合金组织和性能的影响[J]. 金属热处理, 2022, 47(4): 30-38.
[4]	陈连生, 张露友, 田亚强, 杨子旋, 李红斌, 潘红波, 魏英立. 低碳高强舰船用钢的CCT曲线及其组织性能[J]. 金属热处理, 2022, 47(4): 63-68.
[5]	王云龙, 余伟, 张昳, 史佳新, 李明辉. 奥氏体化温度对贝氏体钢等温转变及力学性能的影响[J]. 金属热处理, 2022, 47(4): 80-85.
[6]	骆再斌, 范子泽, 彭振. 轻质高熵合金的研究进展[J]. 金属热处理, 2022, 47(4): 100-107.
[7]	吕杰晟, 宋志刚, 何建国, 丰涵, 郑文杰, 朱玉亮. S32205双相不锈钢冷轧退火组织转变及强塑化机理分析[J]. 金属热处理, 2022, 47(4): 141-145.
[8]	王琪, 吴光亮. 回火温度对1100 MPa级高强钢组织与性能的影响[J]. 金属热处理, 2022, 47(4): 146-150.
[9]	张骥俊, 邢彦锋, 曹菊勇. 超声振动对CMT电弧增材制造铝合金组织与性能的影响[J]. 金属热处理, 2022, 47(4): 159-164.
[10]	刘文彬, 乔龙阳, 潘新宇, 程格, 李爱娜, 裴新军. 淬火温度对刀剪用M390粉末冶金不锈钢组织和性能的影响[J]. 金属热处理, 2022, 47(4): 189-195.
[11]	王瑞琴, 葛鹏, 廖强, 侯鹏, 刘宇. 固溶冷却方式对短时用高温钛合金板材组织和性能的影响[J]. 金属热处理, 2022, 47(4): 196-198.
[12]	王绍灼, 孟晗, 王芬, 樊海卫, 李燕, 唐超. 改善低氧TC4-LC及重熔TC4钛合金性能的热处理工艺[J]. 金属热处理, 2022, 47(4): 204-207.
[13]	陈强, 陈林芳, 杨明华. 18CrNiMo7-6钢的可控气氛高温渗碳工艺[J]. 金属热处理, 2022, 47(4): 231-239.
[14]	刘乃瑜, 曹磊, 郑少梅. 不同沉积温度下CrCN涂层的力学性能[J]. 金属热处理, 2022, 47(4): 240-244.
[15]	刘志桥, 冯庆晓, 李化龙, 李腾飞. 退火工艺对低碳贝氏体钢组织与力学性能的影响[J]. 金属热处理, 2022, 47(3): 53-56.