铸态GCr15钢在连续加热过程中的奥氏体化动力学特征与组织演变

doi:10.13251/j.issn.0254-6051.2021.11.003

金属热处理 ›› 2021, Vol. 46 ›› Issue (11): 17-23.DOI: 10.13251/j.issn.0254-6051.2021.11.003

铸态GCr15钢在连续加热过程中的奥氏体化动力学特征与组织演变

周登虎¹, 侯清宇¹, 韩维雪¹, 江雁², 黄贞益¹

1.安徽工业大学冶金工程学院, 安徽马鞍山 243000;
2.南京钢铁股份有限公司, 江苏南京 211500

收稿日期:2021-05-26 出版日期:2021-11-25 发布日期:2021-12-08
通讯作者: 侯清宇,副教授,E-mail:houqingyu@ahut.edu.cn
作者简介:周登虎(1998—),男,硕士研究生,主要研究方向为金属材料组织性能与控制,E-mail:2305906569@qq.com

Austenitization kinetic characteristics and microstructure evolution of as-cast GCr15 steel during continuous heating

Zhou Denghu¹, Hou Qingyu¹, Han Weixue¹, Jiang Yan², Huang Zhenyi¹

1. School of Metallurgical Engineering, Anhui University of Technology, Ma'anshan Anhui 243000, China;
2. Nanjing Iron and Steel Co., Ltd., Nanjing Jiangsu 211500, China

Received:2021-05-26 Online:2021-11-25 Published:2021-12-08

摘要/Abstract

摘要： 利用DIL805A热膨胀仪记录了铸态GCr15钢在不同的加热速率下(0.5、3、5、30、100 ℃/s)的线膨胀量,获得了不同加热速率下的热膨胀曲线和奥氏体体积转变分数曲线,研究了加热速率对奥氏体化的影响。采用高温光学显微镜对该钢在连续加热过程中的奥氏体转变过程进行了观察分析。研究表明:GC15钢在连续加热过程中的奥氏体转变可分为3个阶段:在760~790 ℃为珠光体向奥氏体的转变、(Fe, Cr)₃C_II向奥氏体中的溶解和奥氏体的成分均匀化温度分别为790~890 ℃及890 ℃以上。并且随着加热速率提高,相变临界温度提高,相变速率提高。在连续加热过程中,铸态GCr15钢的奥氏体转变是一个形核和长大交替进行的过程。

关键词: 铸态GCr15钢, 热膨胀曲线, 转变速率, 奥氏体化, 高温光学显微镜

Abstract: Linear expansion of the as-cast GCr15 steel with different heating rates (0.5, 3, 5, 30, 100 ℃/s) was recorded using DIL805A thermal dilatometer, and their respective thermal expansion curves and austenite volume transformation fraction curves were obtained. The effect of heating rate on austenitization of the as-cast GCr15 steel was studied. The austenite transformation process of the steel during continuous heating was observed and analyzed by means of a high temperature metallurgical microscope. The results show that austenite transformation of the GC15 steel during continuous heating can be divided into three stages: the transformation of pearlite to austenite (760-790 ℃), the dissolution of (Fe, Cr)₃C_II into austenite (790-890 ℃) and the austenite homogenization (>890 ℃). And as the heating rate increases, the critical temperature of phase transition increases, and the rate of phase transition increases. During the continuous heating process, the austenitic transformation of the as-cast GCr15 steel is an alternate process of nucleation and growth.

Key words: as-cast GCr15 steel, thermal expansion curve, transition rate, austenitization, high temperature metallurgical microscope

中图分类号:

TG142

周登虎, 侯清宇, 韩维雪, 江雁, 黄贞益. 铸态GCr15钢在连续加热过程中的奥氏体化动力学特征与组织演变[J]. 金属热处理, 2021, 46(11): 17-23.

Zhou Denghu, Hou Qingyu, Han Weixue, Jiang Yan, Huang Zhenyi. Austenitization kinetic characteristics and microstructure evolution of as-cast GCr15 steel during continuous heating[J]. Heat Treatment of Metals, 2021, 46(11): 17-23.

参考文献

[1]张小垒, 李辉, 徐士新, 等. GCr15钢连续冷却过程中的相变和组织演变[J]. 金属热处理, 2014, 39(3): 99-102.
Zhang Xiaolei, Li Hui, Xu Shixin, et al. Phase transformation and microstructure evolution of GCr15 steel during continuous cooling[J]. Heat Treatment of Metals, 2014, 39(3): 99-102.
[2]田振卓, 霍向东, 李烈军, 等. 终轧后冷却速度对GCr15轴承钢组织和相变的影响[J]. 工业技术创新, 2014, 1(5): 520-524.
Tian Zhenzhuo, Huo Xiangdong, Li Liejun, et al. Effect of cooling after rolling on microstructure and phase transformation of GCr15 bearing steel[J]. Industrial Technology Innovation, 2014, 1(5): 520-524.
[3]刘靖, 韩静涛, 席军良, 等. GCr15轴承钢加热温度与碳化物的溶解扩散[J]. 金属热处理, 2008, 33(10): 87-90.
Liu Jing, Han Jingtao, Xi Junliang, et al. Study of temperature and carbide solution-diffusion for GCr15 bearing steel[J]. Heat Treatment of Metals, 2008, 33(10): 87-90.
[4]孔永华, 李思贝, 周江龙, 等. 等温淬火工艺对GCr15钢领组织和耐磨性的影响[J]. 金属热处理, 2016, 41(7): 95-99.
Kong Yonghua, Li Sibei, Zhou Jianglong, et al. Effect of austempering process parameters on microstructure and wear resistance of GCr15 steel spinning ring[J]. Heat Treatment of Metals, 2016, 41(7): 95-99.
[5]张学飞, 李卓, 崔晓. GCr15轴承套圈热处理变形数值模拟[J]. 轴承, 2020(11): 45-49, 69.
Zhang Xuefei, Li Zhuo, Cui Xiao. Numerical simulation on heat treatment deformation of GCr15 bearing rings[J]. Bearing, 2020(11): 45-49, 69.
[6]王秋成, 张召明, 王露, 等. GCr15钢深冷条件下的组织转变[J]. 低温工程, 2008(6): 24-27.
Wang Qiucheng, Zhang Zhaoming, Wang Lu, et al. Transformation of microstructure of GCr15 steel under cryogenic treatment condition[J]. Cryogenics, 2008(6): 24-27.
[7]余先涛, 张皓然, 屠梦莹, 等. 轴承套圈热处理工艺及其装备[J]. 金属热处理, 2018, 43(10): 86-89.
Yu Xiantao, Zhang Haoran, Tu Mengying, et al. Heat treatment process and equipment for bearing rings[J]. Heat Treatment of Metals, 2018, 43(10): 86-89.
[8]刘波, 黄晓艳. 2016版高碳铬轴承钢标准解析[J]. 轴承, 2017(12): 59-63.
Liu Bo, Huang Xiaoyan. Interpretation of 2016 edition of high-carbon chromium bearing steel standard[J]. Bearing, 2017(12): 59-63.
[9]李志强. GCr15轴承钢加热过程中组织演变规律的实验和模拟[D]. 北京: 北京科技大学, 2017.
Li Zhiqing. Experiment and simulation research on the structure evolution of GCr15 bearing steel during heating process[D]. Beijing: University of Science and Technology Beijing, 2017.
[10]Eggbauer A, Lukas M, Ressel G, et al. In situ analysis of the effect of high heating rates and initial microstructure on the formation and homogeneity of austenite[J]. Journal of Materials Science, 2019, 54(12): 9197-9212.
[11]García De Andrés C. Application of dilatometric analysis to the study of solid-solid phase transformations in steels[J]. Materials Characterization, 2002, 48(1): 101-111.
[12]Danon A, Servant C, Alamo A, et al. Heterogeneous austenite grain growth in 9Cr martensitic steels: Influence of the heating rate and the austenitization temperature[J]. Materials Science & Engineering A, 2003, 348(1): 122-132.
[13]张伟强. 固态金属及合金中的相变[M]. 北京: 国防工业出版社, 2016.
Zhang Weiqing. Phase Transformations in Solid Metals and Alloys[M]. Beijing: National Defense Industry Press, 2016.
[14]Erich S. Anlaufzeit der austenitumwandlung[J]. Archiv Für Dassenhüttenwesen, 1935, 8(12): 565-567.
[15]Ågren J, Vassilev G P. Computer simulations of cementite dissolution in austenite[J]. Materials Science and Engineering, 1984, 64(1): 95-103.
[16]李俊杰, Godfrey Andrew, 刘伟, 等. 连续加热条件下过共析钢奥氏体化研究[J]. 金属学报, 2014, 50(10): 1179-1188.
Li Junjie, Godfrey Andrew, Liu Wei, et al. Investigation of austenitization during continuous heating process in hypereutectoid steels[J]. Acta Metallurgica Sinica, 2014, 50(10): 1179-1188.
[17]徐洲, 赵边城. 金属固态相变原理[M]. 北京: 科学出版社, 2004.

铸态GCr15钢在连续加热过程中的奥氏体化动力学特征与组织演变

Austenitization kinetic characteristics and microstructure evolution of as-cast GCr15 steel during continuous heating

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	王云龙, 余伟, 张昳, 史佳新, 李明辉. 奥氏体化温度对贝氏体钢等温转变及力学性能的影响[J]. 金属热处理, 2022, 47(4): 80-85.
[2]	刘笑笑, 张铮, 张杰, 杨燃, 俞城双, 韩丽娜, 乔珺威. 回火温度对柔性齿轮钢40CrNiMo组织及力学性能的影响[J]. 金属热处理, 2021, 46(8): 99-104.
[3]	杨臣, 柳永宁, 孙俊杰, 王浩, 赵睿澍. 60Si2Mn冷拔珠光体钢丝快速球化退火工艺[J]. 金属热处理, 2021, 46(3): 24-27.
[4]	谢章龙, 陈锋, 胡其龙, 王兆华. 奥氏体化及回火温度对E550级低温钢组织和性能的影响[J]. 金属热处理, 2021, 46(1): 65-69.
[5]	彭旭, 卜恒勇, 李萌蘖. 5CrNiMoV钢的奥氏体化动力学预测[J]. 金属热处理, 2020, 45(9): 227-232.
[6]	杜晓洁, 何宜柱. E690钢奥氏体化过程的内耗分析[J]. 金属热处理, 2020, 45(8): 12-16.
[7]	刘豪, 张立文, 李飞, 张驰, 毛培刚, 李超群. 38CrMoAl钢的奥氏体晶粒长大行为[J]. 金属热处理, 2020, 45(8): 38-42.
[8]	笪光杰, 杨忠民, 王凯, 陈颖, 王慧敏, 李少华. 奥氏体化温度和冷却速率对含Nb高碳钢组织性能的影响[J]. 金属热处理, 2020, 45(6): 1-6.
[9]	李俊, 黄健, 贾涛. 初始组织对20CrMnTi钢伪渗碳过程中奥氏体化相变与晶粒长大行为的影响[J]. 金属热处理, 2020, 45(6): 157-162.
[10]	周敏1,2，厉勇2，黄顺喆2，王春旭2，韩顺2，刘荣佩1. 奥氏体化温度对二次硬化渗碳钢组织与力学性能的影响[J]. 金属热处理, 2017, 42(2): 108-112.
[11]	黄曼曼1，琚子来1，姜利坤2, 郭建斌3. 新型含碳化物马氏体球墨铸铁的热处理工艺[J]. 金属热处理, 2016, 41(9): 128-130.
[12]	高韩锋1.2，李晓源2. 热处理制度对低碳马氏体钢组织及性能的影响[J]. 金属热处理, 2016, 41(6): 131-134.
[13]	常开地，尹立新，周晓伟，王萍，张玮. 奥氏体化温度对60Si2CrVAT弹簧钢晶粒尺寸和硬度的影响[J]. 金属热处理, 2016, 41(4): 35-37.
[14]	吝章国1，熊自柳1，刘宏强1，张琳2. 合金元素对高强汽车钢板相变规律的影响[J]. 金属热处理, 2016, 41(2): 28-31.
[15]	许文博，魏绍鹏，石伟，王罡，融亦鸣. 加热速率对FV520B钢奥氏体化相变动力学的影响[J]. 金属热处理, 2016, 41(2): 183-187.