不同两相区淬火温度对9Ni钢组织与性能的影响

doi:10.13251/j.issn.0254-6051.2021.07.004

金属热处理 ›› 2021, Vol. 46 ›› Issue (7): 18-22.DOI: 10.13251/j.issn.0254-6051.2021.07.004

不同两相区淬火温度对9Ni钢组织与性能的影响

李荣斌^1,2,3, 秦品强¹, 陈永强¹, 李珂¹, 龙文宇¹

1.上海理工大学材料科学与工程学院, 上海 200093;
2.上海电机学院材料学院, 上海 201306;
3.上海电机学院上海大件热制造工程技术研究中心, 上海 201306

收稿日期:2021-04-02 出版日期:2021-07-25 发布日期:2021-12-10
作者简介:李荣斌(1969—),男,教授,博士,主要研究方向为薄膜材料、材料结构模拟,E-mail:rblesh@126.com。
基金资助:
上海市大件热制造工程技术中心项目(18DZ253400);临港新片区高新产业和科技创新专项项目(SH-LG-GK-2020-28);上海市地方院校能力建设项目(21010500900)

Effect of different intercritical quenching temperature on microstructure and properties of 9Ni Steel

Li Rongbin^1,2,3, Qin Pinqiang¹, Chen Yongqiang¹, Li Ke¹, Long Wenyong¹

1. Academy of Material Science and Engineering, University of Shanghai for Science and Technology, Shanghai 200093, China;
2. Academy of Materials, Shanghai Dianji University, Shanghai 201306, China;
3. Shanghai Engineering Research Center of Large Piece Hot Manufacturing, Shanghai Dianji University, Shanghai 201306, China

Received:2021-04-02 Online:2021-07-25 Published:2021-12-10

摘要/Abstract

摘要： 通过SEM、XRD、疲劳试验机、冲击试验机等分析了620~680 ℃区间不同两相区淬火温度对9Ni钢强度和低温冲击性能的影响。结果表明,回转奥氏体含量和稳定性对材料性能影响显著,随着两相区淬火温度的升高,9Ni钢抗拉强度不断增大,而低温冲击性能呈现先升高后降低的非线性趋势。在640 ℃时,试样的回转奥氏体含量最高,达9.65%;断后伸长率最高,达到32.67%;冲击吸收能量最高,常温下达到332.83 J,-196 ℃条件下为297.69 J,总体展现出良好的强韧性。

关键词: 9Ni钢, 两相区淬火温度, 微观组织, 回转奥氏体, 力学性能

Abstract: Effects of different intercritical quenching temperatures in the range of 620-680 ℃ on the strength and low temperature impact property of 9Ni steel were analyzed by means of SEM, XRD, fatigue testing machine, and impact testing machine. The results show that the content and stability of reversed austenite have a significant effect on the material properties. With the increase of intercritical quenching temperature, the tensile strength of the steel continues to increase, while the low temperature impact property presents a nonlinear trend of first increasing and then decreasing. When the intercritical quenching temperature is 640 ℃, the reversed austenite content, the elongation after fracture, the impact absorbed energy of the specimens all are the highest, respectively being 9.65%, 32.67%, 332.83 J at room temperature and 297.69 J at -196 ℃, showing the best match of strength and toughness on the whole.

Key words: 9Ni steel, intercritical quenching temperature, microstructure, reversed austenite, mechanical properties

中图分类号:

TG142.79

李荣斌, 秦品强, 陈永强, 李珂, 龙文宇. 不同两相区淬火温度对9Ni钢组织与性能的影响[J]. 金属热处理, 2021, 46(7): 18-22.

Li Rongbin, Qin Pinqiang, Chen Yongqiang, Li Ke, Long Wenyong. Effect of different intercritical quenching temperature on microstructure and properties of 9Ni Steel[J]. Heat Treatment of Metals, 2021, 46(7): 18-22.

参考文献

[1] 杨跃辉, 蔡庆伍, 武会宾, 等. 两相区热处理过程中回转奥氏体的形成规律及其对9Ni钢低温韧性的影响[J]. 金属学报, 2009, 45(3): 270-274.
Yang Yuehui, Cai Qingwu, Wu Huibin, et al. Formation of reversed austenite and its effect on cryogenic toughness of 9Ni steel during two-phase region heat treatment[J]. Acta Metallurgica Sinica, 2009, 45(3): 270-274.
[2] 郭魁文, 朱健, 王秉新. 两相区热处理对9Ni钢低温韧性的影响[J]. 辽宁石油化工大学学报, 2010, 30(2): 26-28.
Guo Huaiwen, Zhu Jian, Wang Bingxin. Influence of two-phase region heat treatment on cryogenic toughness in 9Ni steel[J]. Journal of Liaoning Petrochemical University, 2010, 30(2): 26-28.
[3] Kinney C C, Pytlewski K R, Khachaturyan A G, et al. The microstructure of lath martensite in quenched 9Ni steel[J]. Acta Materialia, 2014, 69: 372-385
[4] 杨跃辉, 苑少强, 刘坚, 等. 快速加热回火过程中9Ni钢组织的演化[J]. 材料热处理学报, 2019, 40(6): 97-102.
Yang Yuehui, Yuan Shaoqiang, Liu Jian, et al. Microstructure evolution of 9Ni steel during rapid heating and tempering[J]. Transactions of Materials and Heat Treatment, 2019, 40(6): 97-102.
[5] Nakanishi D, Kawabata T, Aihara S. Effect of dispersed retained γ-Fe on brittle crack arrest toughness in 9% Ni steel in cryogenic temperatures[J]. Materials Science and Engineering A, 2018, 723: 238-246.
[6] 谢章龙, 刘振宇, 陈俊, 等. 9Ni钢薄板的奥氏体化温度及强韧化因素分析[J]. 钢铁研究学报, 2011, 23(9): 37-38.
Xie Zhanglong, Liu Zhenyu, Chen Jun, et al. Austenitizing temperature for 9Ni steel thin plate and analysis of strengthening and toughening factors[J]. Journal of Iron and Steel Research, 2011, 23(9): 37-38.
[7] 曹宏玮, 罗兴宏, 刘实. 淬火温度对7Ni钢低温力学性能的影响[J]. 材料研究学报, 2018, 32(5): 388-394.
Cao Hongwei, Luo Xinghong, Liu Shi. Effect of quenching temperature on cryogenic mechanical properties of a 7Ni steel[J]. Chinese Journal of Materials Research, 2018, 32(5): 388-394.
[8] 许立雄, 武会宾, 牟丹. 两相区淬火对7Ni钢微观组织和力学性能的影响[J]. 材料工程, 2018, 46(8): 113-119.
Xu Lixiong, Wu Huibin, Mou Dan. Effect of quenching in dual-phase region on microstructure and mechanical properties of 7Ni steel[J]. Journal of Materials Engineering, 2018, 46(8): 113-119.
[9] 赵宏禹, 刘荣佩, 王长军, 等. QLT与QT热处理工艺对9Ni低温钢性能的影响[J]. 金属热处理, 2018, 43(12): 100-104.
Zhao Hongyu, Liu Rongpei, Wang Changjun, et al. Influence of QLT and QT heat treatment process on properties of 9Ni steel[J]. Heat Treatment of Metals, 2018, 43(12): 100-104.
[10] Cheng J H, Shen J C, He Y Z, et al. Effect of quenching lamellarizing and tempering process on strength and toughness of 9NiCrMo steel[J]. Iron and Steel, 2014, 49(9): 87-91.
[11] Jang J, Ju J B, Lee B W, et al. Effects of microstructural change on fracture characteristics in coarse-grained heat-affected zones of QLT processed 9%Ni steel[J]. Materials Science and Engineering A, 2003, 340(1): 68-79.
[12] Zhang J M, Li H, Yang F, et al. Effect of heat treatment process on mechanical properties and microstructure of a 9% Ni steel for large LNG storage tanks[J]. Journal of Materials Engineering and Performance, 2013, 22(12): 3867-3871.
[13] 刘文斌, 战国锋, 黄峰. 回火温度对7Ni钢组织和性能的影响[J]. 金属热处理, 2020, 45(12): 63-68.
Liu Wenbin, Zhan Guofeng, Huang Feng. Effect of tempering temperature on microstructure and properties of 7Ni steel[J]. Heat Treatment of Metals, 2020, 45(12): 63-68.
[14] Yang Y H, Cai Q W, Wu H B. Formation of reversed austenite and its effect on cryogenic toughness of 9Ni steel during two-phase region heat treatment[J]. Acta Metallurgica Sinica, 2009, 45(3): 270-274.
[15] Yang Y H, Cai Q W, Tang D, et al. Precipitation and stability of reversed austenite in 9Ni steel[J]. International Journal of Minerals Metallurgy and Materials, 2010, 17(5): 587-595.
[16] 张坤, 唐荻, 武会宾. 逆转变奥氏体对9Ni钢低温冲击韧度的影响[J]. 热加工工艺, 2012, 41(8): 177-179.
Zhang Kun, Tang Di, Wu Huibin. Effect of reversed austenite on impact toughness of 9Ni steel at low temperature[J]. Hot Working Technology, 2012, 41(8): 177-179.

不同两相区淬火温度对9Ni钢组织与性能的影响

Effect of different intercritical quenching temperature on microstructure and properties of 9Ni Steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	梁恩溥, 徐乐, 杨勇, 王毛球. 添加Al、Cu对40CrNi3MoV钢组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 17-23.
[2]	祁晓亮, 李岩, 定巍, 赵增武. 含Al中锰TRIP钢原始组织对临界退火后组织与力学性能的影响[J]. 金属热处理, 2022, 47(4): 24-29.
[3]	陈保安, 张静媛, 祝志祥, 韩钰, 潘学东, 张磊, 陈素红. 化学成分对高强Al-Mg-Si合金组织和性能的影响[J]. 金属热处理, 2022, 47(4): 30-38.
[4]	陈东俊, 李广阳, 刘刚. 时效处理对AlSi9Cu3压铸铝合金组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 53-56.
[5]	陈连生, 张露友, 田亚强, 杨子旋, 李红斌, 潘红波, 魏英立. 低碳高强舰船用钢的CCT曲线及其组织性能[J]. 金属热处理, 2022, 47(4): 63-68.
[6]	王云龙, 余伟, 张昳, 史佳新, 李明辉. 奥氏体化温度对贝氏体钢等温转变及力学性能的影响[J]. 金属热处理, 2022, 47(4): 80-85.
[7]	骆再斌, 范子泽, 彭振. 轻质高熵合金的研究进展[J]. 金属热处理, 2022, 47(4): 100-107.
[8]	李立, 曾艳, 吴晓春. 4Cr5Mo2VCo钢的热处理工艺优化[J]. 金属热处理, 2022, 47(4): 133-140.
[9]	吕杰晟, 宋志刚, 何建国, 丰涵, 郑文杰, 朱玉亮. S32205双相不锈钢冷轧退火组织转变及强塑化机理分析[J]. 金属热处理, 2022, 47(4): 141-145.
[10]	王琪, 吴光亮. 回火温度对1100 MPa级高强钢组织与性能的影响[J]. 金属热处理, 2022, 47(4): 146-150.
[11]	张骥俊, 邢彦锋, 曹菊勇. 超声振动对CMT电弧增材制造铝合金组织与性能的影响[J]. 金属热处理, 2022, 47(4): 159-164.
[12]	刘文彬, 乔龙阳, 潘新宇, 程格, 李爱娜, 裴新军. 淬火温度对刀剪用M390粉末冶金不锈钢组织和性能的影响[J]. 金属热处理, 2022, 47(4): 189-195.
[13]	王瑞琴, 葛鹏, 廖强, 侯鹏, 刘宇. 固溶冷却方式对短时用高温钛合金板材组织和性能的影响[J]. 金属热处理, 2022, 47(4): 196-198.
[14]	王绍灼, 孟晗, 王芬, 樊海卫, 李燕, 唐超. 改善低氧TC4-LC及重熔TC4钛合金性能的热处理工艺[J]. 金属热处理, 2022, 47(4): 204-207.
[15]	陈强, 陈林芳, 杨明华. 18CrNiMo7-6钢的可控气氛高温渗碳工艺[J]. 金属热处理, 2022, 47(4): 231-239.