长时服役后T92钢管的微观组织及力学性能变化

doi:10.13251/j.issn.0254-6051.2021.07.006

金属热处理 ›› 2021, Vol. 46 ›› Issue (7): 31-36.DOI: 10.13251/j.issn.0254-6051.2021.07.006

长时服役后T92钢管的微观组织及力学性能变化

何利军¹, 周龙¹, 汤淳坡¹, 郭小钢¹, 金晓², 赵彦芬², 薛飞², 张国栋²

1.国家能源集团泰州发电有限公司, 江苏泰州 225327;
2.苏州热工研究院有限公司, 江苏苏州 215004

收稿日期:2021-02-21 出版日期:2021-07-25 发布日期:2021-12-10
通讯作者: 张国栋,研究员级高级工程师,博士,E-mail:zhanggdln@163.com
作者简介:何利军(1974—),男,高级工程师,主要研究方向为火电厂设备管理与运行,E-mail: lijun.he.q@chnenergy.com.cn。
基金资助:
国家重点研发计划(2017YFB0702200);广东省基础与应用基础研究重大项目(2019B030302011)

Microstructure evolution and property change of T92 heat resistant steel pipe after long term service

He Lijun¹, Zhou Long¹, Tang Chunpo¹, Guo Xiaogang¹, Jin Xiao², Zhao Yanfen², Xue Fei², Zhang Guodong²

1. China Energy Taizhou Power Generation Co.,Ltd., Taizhou Jiangsu 225327, China;
2. Suzhou Nuclear Power Institute, Suzhou Jiangsu 215004, China

Received:2021-02-21 Online:2021-07-25 Published:2021-12-10

摘要/Abstract

摘要： 通过扫描电镜、透射电镜等技术定量研究了T92耐热钢服役80 000 h后的微观组织结构和力学性能,并与未服役的同批次材料进行了对比。结果表明,在服役80 000 h后,T92钢管材的马氏体板条上析出了大量的M₂₃C₆相和Laves相,在板条内部析出MX相,马氏体板条宽度明显增加,但仍然保持着典型的马氏体板条形貌。T92钢室温和610 ℃高温抗拉强度、屈服强度均较未服役样品的低,但室温条件下性能相差较小,而高温条件下的下降幅度较大,且屈服强度接近标准要求的下限。析出相强化和板条强化是T92耐热钢在长时服役后仍具有较高性能的原因。

关键词: T92钢管服役, 微观结构, 力学性能, 强化机制

Abstract: Microstructure evolution and mechanical properties of the T92 heat resistant steel pipe after 80 000 h service were studied by means of scanning electron microscopy and transmission electron microscopy and compared with the same batch of standby materials. The results show that after 80 000 h service, a large amount of M₂₃C₆ phase and Laves phase are precipitated on the martensite lath of the T92 steel, and MX phase is precipitated inside the lath. The width of the martensite slats has also increased significantly after service, but the typical martensitic slats are still maintained. The tensile strength and yield strength at room temperature and high temperature (610 ℃) of the T92 steel are reduced compared to the standby steel, and the difference of which at room temperature is small, while it decrease largely at high temperature. Precipitated phase strengthening and lath strengthening are the fundamental reasons for high performance of the T92 heat resistant steel after long-term service.

Key words: T92 steel pipe service, microstructure, mechanical properties, strengthening mechanism

中图分类号:

TG142.73

何利军, 周龙, 汤淳坡, 郭小钢, 金晓, 赵彦芬, 薛飞, 张国栋. 长时服役后T92钢管的微观组织及力学性能变化[J]. 金属热处理, 2021, 46(7): 31-36.

He Lijun, Zhou Long, Tang Chunpo, Guo Xiaogang, Jin Xiao, Zhao Yanfen, Xue Fei, Zhang Guodong. Microstructure evolution and property change of T92 heat resistant steel pipe after long term service[J]. Heat Treatment of Metals, 2021, 46(7): 31-36.

参考文献

[1] Hald J. Metallurgy and creep properties of new 9-12%Cr steels[J]. Materials Technology, 1996, 67(9): 369-374.
[2] Abe F. Precipitate design for creep strengthening of 9%Cr tempered martensitic steel for ultra-supercritical power plants[J]. Science and Technology of Advanced Materials, 2008, 9(1): 013002.
[3] Hald J. Microstructure and long-term creep properties of 9-12%Cr steels[J]. International Journal of Pressure Vessels and Piping, 2008, 85(1/2): 30-37.
[4] Abe F, Horiuchi T, Taneike M, et al. Stabilization of martensitic microstructure in advanced 9Cr steel during creep at high temperature[J]. Materials Science and Engineering A, 2004, 378(1/2): 299-303.
[5] Cerjak H, Hofer P, Schaffernak B. The influence of microstructural aspects on the service behaviour of advanced power plant steels[J]. ISIJ International, 1999, 39(9): 874-888.
[6] 严鹏. 新型马氏体耐热钢G115的组织与性能研究[D]. 北京: 清华大学, 2014.
[7] 王学, 于淑敏, 任遥遥, 等. T92钢时效的Laves相演化行为[J]. 金属学报, 2014, 50(10): 1195-1202.
Wang Xue, Yu Shumin, Ren Yaoyao, et al. Laves phase evolution in T92 steel during ageing[J]. Acta Metallurgica Sinica, 2014, 50(10): 1195-1202.
[8] Prawoto Y, Jasmawati N, Sumeru K. Effect of prior austenite grain size on the morphology and mechanical properties of martensite in medium carbon steel[J]. Journal of Materials Science and Technology, 2012, 28(5): 461-466.
[9] Khayatzadeh S, Tanner D W J, Truman C E, et al. Creep deformation and stress relaxation of a martensitic T92 steel at 650 ℃[J]. Engineering Fracture Mechanics, 2017, 175: 57-71.
[10] Sklenička V, Kuchařová K, Král P, et al. The effect of hot bending and thermal ageing on creep and microstructure evolution in thick-walled P92 steel pipe[J]. Materials Science and Engineering A, 2015, 644: 297-309.
[11] 彭志方, 蔡黎胜, 彭芳芳, 等. T92钢625 ℃持久性能分段特征与各段中M₂₃C₆及Laves相相参数的定量变化研究[J]. 金属学报, 2010, 46(4): 429-434.
Peng Zhifang, Cai Lisheng, Peng Fangfang, et al. Study on the multi-segment feature of 625 ℃ creep-repture property and the quatitative change of phase parameters of M₂₃C₆and Laves phases in each segment of T92 steel[J]. Acta Metallurgica Sinica, 2010, 46(4): 429-434.
[12] 王学, 李勇, 任遥遥, 等. Laves相析出对T92钢合金元素再分布的影响[J]. 金属学报, 2014, 50(10): 1203-1209.
Wang Xue, Li Yong, Ren Yaoyao, et al. Effect of Laves phase precipitation on redistribution of alloying elements in T92 steel[J]. Acta Metallurgica Sinica, 2014, 50(10): 1203-1209.
[13] Korcakova J H L, Somers M A J. Quantification of Laves phase particle size in 9CrW steel[J]. Materials Characterization, 2001, 47(2): 111-117.
[14] Zhang J, Du B S, Li X M, et al. Microstructure evolution of T92 steel weld metal after service for 8000 h[J]. Kovove Materialy, 2017, 55(2): 115-121.
[15] Xu Y, Nie Y, Wang M, et al. The effect of microstructure evolution on the mechanical properties of martensite ferritic steel during long-term aging[J]. Acta Materialia, 2017, 131: 110-122.
[16] Lee K H, Park D B, Kwun S L, et al. Effect of creep deformation on the microstructural evolution of 11CrMoVNb heat resistant steel[J]. Materials Science and Engineering A, 2012, 536: 92-97.
[17] Xiao B, Xu L Y, Zhao L, et al. Microstructure evolution and fracture mechanism of a novel 9Cr tempered martensite ferritic steel during short-term creep[J]. Materials Science and Engineering A, 2017, 707: 466-477.
[18] Golański G, Kolan C, Jasak J. Creep[M]. Inter: Intechopen, 2018.
[19] 潘金生, 田民波, 仝健民. 材料科学基础[M]. 北京: 清华大学出版社, 2011.
[20] Maruyama K S K, Koike J. Strengthening mechanisms of creep resistant tempered martensitic steel[J]. ISIJ International, 2016, 41(6): 641-653.
[21] Bao H S, Cheng S C, Liu Z D, et al. Aging precipitates and strengthening mechanism of T122 boiler steel[J]. Journal of Iron and Steel Research, International, 2010, 17(2): 67-73.
[22] Jin X, Zhu B Y, Li Y F, et al. Effect of the microstructure evolution on the high-temperature strength of P92 heat-resistant steel for different servicetimes[J]. International Journal of Pressure Vessels and Piping, 2020, 186: 104131.

长时服役后T92钢管的微观组织及力学性能变化

Microstructure evolution and property change of T92 heat resistant steel pipe after long term service

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	梁恩溥, 徐乐, 杨勇, 王毛球. 添加Al、Cu对40CrNi3MoV钢组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 17-23.
[2]	祁晓亮, 李岩, 定巍, 赵增武. 含Al中锰TRIP钢原始组织对临界退火后组织与力学性能的影响[J]. 金属热处理, 2022, 47(4): 24-29.
[3]	陈保安, 张静媛, 祝志祥, 韩钰, 潘学东, 张磊, 陈素红. 化学成分对高强Al-Mg-Si合金组织和性能的影响[J]. 金属热处理, 2022, 47(4): 30-38.
[4]	陈连生, 张露友, 田亚强, 杨子旋, 李红斌, 潘红波, 魏英立. 低碳高强舰船用钢的CCT曲线及其组织性能[J]. 金属热处理, 2022, 47(4): 63-68.
[5]	王云龙, 余伟, 张昳, 史佳新, 李明辉. 奥氏体化温度对贝氏体钢等温转变及力学性能的影响[J]. 金属热处理, 2022, 47(4): 80-85.
[6]	骆再斌, 范子泽, 彭振. 轻质高熵合金的研究进展[J]. 金属热处理, 2022, 47(4): 100-107.
[7]	吕杰晟, 宋志刚, 何建国, 丰涵, 郑文杰, 朱玉亮. S32205双相不锈钢冷轧退火组织转变及强塑化机理分析[J]. 金属热处理, 2022, 47(4): 141-145.
[8]	王琪, 吴光亮. 回火温度对1100 MPa级高强钢组织与性能的影响[J]. 金属热处理, 2022, 47(4): 146-150.
[9]	张骥俊, 邢彦锋, 曹菊勇. 超声振动对CMT电弧增材制造铝合金组织与性能的影响[J]. 金属热处理, 2022, 47(4): 159-164.
[10]	刘文彬, 乔龙阳, 潘新宇, 程格, 李爱娜, 裴新军. 淬火温度对刀剪用M390粉末冶金不锈钢组织和性能的影响[J]. 金属热处理, 2022, 47(4): 189-195.
[11]	王瑞琴, 葛鹏, 廖强, 侯鹏, 刘宇. 固溶冷却方式对短时用高温钛合金板材组织和性能的影响[J]. 金属热处理, 2022, 47(4): 196-198.
[12]	王绍灼, 孟晗, 王芬, 樊海卫, 李燕, 唐超. 改善低氧TC4-LC及重熔TC4钛合金性能的热处理工艺[J]. 金属热处理, 2022, 47(4): 204-207.
[13]	陈强, 陈林芳, 杨明华. 18CrNiMo7-6钢的可控气氛高温渗碳工艺[J]. 金属热处理, 2022, 47(4): 231-239.
[14]	刘乃瑜, 曹磊, 郑少梅. 不同沉积温度下CrCN涂层的力学性能[J]. 金属热处理, 2022, 47(4): 240-244.
[15]	刘志桥, 冯庆晓, 李化龙, 李腾飞. 退火工艺对低碳贝氏体钢组织与力学性能的影响[J]. 金属热处理, 2022, 47(3): 53-56.