时效处理对优质GH738合金组织及力学性能的影响

doi:10.13251/j.issn.0254-6051.2021.12.003

金属热处理 ›› 2021, Vol. 46 ›› Issue (12): 13-18.DOI: 10.13251/j.issn.0254-6051.2021.12.003

时效处理对优质GH738合金组织及力学性能的影响

吴玉博^1,2, 杨成斌^1,2, 侯为学^1,2, 荣义^1,2, 李春^1,2, 录云杰^1,2, 李伶俐¹

1.北京钢研高纳科技股份有限公司, 北京 100081;
2.钢铁研究总院高温合金新材料北京市重点实验室, 北京 100081

收稿日期:2021-09-18 出版日期:2021-12-25 发布日期:2022-02-18
通讯作者: 杨成斌,工程师,硕士,E-mail:yangchengbin0201@163.com
作者简介:吴玉博(1983—),男,工程师,硕士,主要研究方向为镍基变形高温合金,E-mail:wyb20111103@126.com。

Effect of aging treatment on microstructure and mechanical properties of high quality GH738 alloy

Wu Yubo^1,2, Yang Chengbin^1,2, Hou Weixue^1,2, Rong Yi^1,2, Li Chun^1,2, Lu Yunjie^1,2, Li Lingli¹

1. Gaona Areo Materials Co., Ltd., CISRI, Beijing 100081, China;
2. Beijing Key Laboratory of Advanced High Temperature Materials, Central Iron and Steel Research Institute, Beijing 100081, China

Received:2021-09-18 Online:2021-12-25 Published:2022-02-18

摘要/Abstract

摘要： 采用力学性能测试与组织观察相结合的方式研究了时效温度和保温时间对优质GH738合金组织及性能的影响规律。结果表明,时效温度和时间均会对γ′相的体积分数和尺寸产生影响。当时效温度在720~800 ℃时,随着时效温度升高,合金强度下降,一次和二次γ′相分别长大30 nm和8 nm,一次γ′相体积分数增加,二次γ′相体积分数减少,时效温度为800 ℃时一次γ′相体积分数达到峰值,约为8%。当保温时间为0~48 h时,随时效时间延长,合金强度先升高后降低,两类γ′相分别长大20 nm和6 nm,一次γ′相体积分数先增后减,二次γ′相体积分数则变化相反。当保温时间为8 h时,两类γ′相体积分数分别达到峰/谷值,含量约为8%和12%。γ′相尺寸和体积分数的变化,特别是体积分数的变化,导致位错的两种强化机制作用效果不同,致使强度发生变化。

关键词: 优质GH738合金, 时效处理, γ′相, 组织, 力学性能

Abstract: Effect of aging temperature and time on microstructure and properties of high quality GH738 alloy was studied by means of mechanical testing and microstructure observation. The results show that the aging temperature and time both affect the fraction and size of γ′ phase. When the aging temperature is between 720 ℃ and 800 ℃, with the increase of aging temperature, the strength of the alloy decreases, the primary and secondary γ′ phases grow up by 30 nm and 8 nm, respectively. The volume fraction of the primary γ′ phase increases, and that of the secondary γ′ phase decreases. When the aging temperature is 800 ℃, the volume fraction of the primary γ′ phase reaches the peak value as about 8%. When the aging time is between 0 and 48 h, with the increase of aging time, the alloy strength first increases and then decreases. The two types of γ′ phase grow up by 20 nm and 6 nm, respectively. The volume fraction of the primary γ′ phase increases first and then decreases, and that of the secondary γ′ phase just changes as the opposite. When the aging time is 8 h, the volume fractions of two types of γ′ phase reach their peak/valley values respectively, as about 8% and 12%. The changes in the size and volume fraction of the γ′ phase, especially volume fraction, lead to different effects of two strengthening mechanisms of dislocations, resulting in change in strength.

Key words: high quality GH738 alloy, aging treatment, γ′ phase, microstructure, mechanical properties

中图分类号:

TG132.3

吴玉博, 杨成斌, 侯为学, 荣义, 李春, 录云杰, 李伶俐. 时效处理对优质GH738合金组织及力学性能的影响[J]. 金属热处理, 2021, 46(12): 13-18.

Wu Yubo, Yang Chengbin, Hou Weixue, Rong Yi, Li Chun, Lu Yunjie, Li Lingli. Effect of aging treatment on microstructure and mechanical properties of high quality GH738 alloy[J]. Heat Treatment of Metals, 2021, 46(12): 13-18.

参考文献

[1]荣义, 成磊, 唐超, 等. 固溶冷却介质对优质GH738合金组织及力学性能的影响[J]. 钢铁研究学报, 2016, 28(11): 74-78.
Rong Yi, Cheng Lei, Tang Chao, et al. Effects of cooling rate mediums for solution treatment on the microstructure and mechanical properties of high quality GH738 alloy[J]. Journal of Iron and Steel Research, 2016, 28(11): 74-78.
[2]陈国良, 谢锡善, 孟庆麟, 等. 高温合金学[M]. 北京: 冶金工业出版社, 1988.
[3]曲敬龙, 史玉亭, 荣义, 等. 优质GH738合金高温均匀化处理工艺研究[C]//第十四届中国高温合金年会论文集. 北京: 中国金属学会高温材料分会, 2019: 274-277.
[4]曲敬龙, 谷雨, 陈正阳, 等. 不同开坯工艺对优质GH738合金中夹杂物分布的影响[C]//第十四届中国高温合金年会论文集. 北京: 中国金属学会高温材料分会, 2019: 278-281.
[5]荣义, 张麦仓, 杨成斌, 等. 优质GH738合金热变形过程中的再结晶机制[J]. 钢铁研究学报, 2021, 33(6): 530-538.
Rong Yi, Zhang Maicang, Yang Chengbin, et al. Recrystallization mechanism of high quality GH738 alloy during hot deformation[J]. Journal of Iron and Steel Research, 2021, 33(6): 530-538.
[6]唐超, 于凯, 罗俊鹏, 等. GH4738合金断口附近的组织特征与持久寿命的关联性研究[J]. 热加工工艺, 2021, 50(14): 62-67.
Tang Chao, Yu Kai, Luo Junpeng, et al. Investigation on relationship between microstructure characteristic near fracture and creep rupture life for GH4738 alloy[J]. Hot Working Technology, 2021, 50(14): 62-67.
[7]曲敬龙, 荣义, 张麦仓, 等. 固溶温度对优质GH4738合金组织及力学性能的影响[C]//第十三届中国高温合金年会论文集. 北京: 中国金属学会高温材料分会, 2015: 154-158.
[8]李钢, 荣义, 杨成斌, 等. 稳定化处理对优质GH738合金组织及力学性能的影响[J]. 材料热处理学报, 2021, 42(7): 65-71.
Li Gang, Rong Yi, Yang Chengbin, et al. Effect of stabilizing treatment on microstructure and mechanical properties of high quality GH738 alloy[J]. Transactions of Materials and Heat Treatment, 2021, 42(7): 65-71.
[9]姚志浩, 董建新, 陈旭, 等. GH738高温合金长期时效过程中γ′相演变规律[J]. 材料热处理学报, 2013, 34(1): 31-37.
Yao Zhihao, Dong Jianxin, Chen Xu, et al. Gamma prime phase evolution during long-time exposure for GH738 superalloy[J]. Transactions of Materials and Heat Treatment, 2013, 34(1): 31-37.
[10]赵双群, 谢锡善. WASPALOY合金长期时效过程中的组织演变和性能变化[J]. 机械工程材料, 2006(10): 62-65.
Zhao Shuanqun, Xie Xishan. Mechanical properties and microstructure evolution of WASPALOY after long exposure[J]. Materials for Mechanical Engineering, 2006(10): 62-65.
[11]杨德庄. 位错与金属强化机制[M]. 哈尔滨: 哈尔滨工业大学出版社, 1991.
[12]Murphy H J, Sims C T, Hecheman G R. Long-time structures and properties of three high-strength nickel-base alloys[J]. Transactions of the Metallurgical Society of AIME, 1967, 239: 1961-1978.
[13]Decker R F. Strengthening mechanisms in nickel-base superalloys[C]//Steel Strengthening Mechanisms Symposium. Zurich: Climax Molybdenum Company, 1969: 1-24.
[14]Wessman A, Laurence A, Cormier J, et al. Thermal stability of cast and wrought alloy Rene 65[C]//13th International Symposium on Superalloys. Seven Springs, 2016: 793-800.
[15]袁晓飞, 丁贤飞, 八木晃一, 等. GH4098合金短时持久性能的研究[J]. 稀有金属材料与工程, 2015, 44(10): 2419-2428.
Yuan Xiaofei, Ding Xianfei, Yagi Koichi, et al. Short time stress rupture property in GH4098 alloy[J]. Rare Metal Materials and Engineering, 2015, 44(10): 2419-2428.

时效处理对优质GH738合金组织及力学性能的影响

Effect of aging treatment on microstructure and mechanical properties of high quality GH738 alloy

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	王玉岱, 刘洋, 朱言言, 田象军, 程序, 冉先喆, 钱婷婷. 热处理对复合制造AerMet100超高强度钢组织均匀性与拉伸性能的影响[J]. 金属热处理, 2022, 47(4): 1-9.
[2]	张子延, 陈君, 陈晓亚, 李全安, 刘建鑫. 固溶时效处理对Mg-4Sm-3Gd-0.5Zr合金显微组织和耐蚀性能的影响[J]. 金属热处理, 2022, 47(4): 10-16.
[3]	梁恩溥, 徐乐, 杨勇, 王毛球. 添加Al、Cu对40CrNi3MoV钢组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 17-23.
[4]	祁晓亮, 李岩, 定巍, 赵增武. 含Al中锰TRIP钢原始组织对临界退火后组织与力学性能的影响[J]. 金属热处理, 2022, 47(4): 24-29.
[5]	陈保安, 张静媛, 祝志祥, 韩钰, 潘学东, 张磊, 陈素红. 化学成分对高强Al-Mg-Si合金组织和性能的影响[J]. 金属热处理, 2022, 47(4): 30-38.
[6]	陈东俊, 李广阳, 刘刚. 时效处理对AlSi9Cu3压铸铝合金组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 53-56.
[7]	陈连生, 张露友, 田亚强, 杨子旋, 李红斌, 潘红波, 魏英立. 低碳高强舰船用钢的CCT曲线及其组织性能[J]. 金属热处理, 2022, 47(4): 63-68.
[8]	贾昌远, 霍元明, 何涛, 霍存龙, 刘克然. 40CrNiMo钢高温拉伸变形行为和组织演变规律[J]. 金属热处理, 2022, 47(4): 69-74.
[9]	王云龙, 余伟, 张昳, 史佳新, 李明辉. 奥氏体化温度对贝氏体钢等温转变及力学性能的影响[J]. 金属热处理, 2022, 47(4): 80-85.
[10]	刘丽艳, 毕文珍, 韦习成. Mn元素对热冲压钢镀锌层组织演变的影响[J]. 金属热处理, 2022, 47(4): 93-99.
[11]	骆再斌, 范子泽, 彭振. 轻质高熵合金的研究进展[J]. 金属热处理, 2022, 47(4): 100-107.
[12]	付锡彬, 陈子豪, 张可, 赵时雨, 孙新军, 朱正海, 梁小凯, 雍岐龙. 淬火温度对高Ti低合金耐磨钢组织及力学性能的影响[J]. 金属热处理, 2022, 47(4): 122-127.
[13]	宿鹏吉, 麻永林, 董丽丽, 杨雪峰. 磁场预退火处理对CGO钢组织与织构的影响[J]. 金属热处理, 2022, 47(4): 128-132.
[14]	李立, 曾艳, 吴晓春. 4Cr5Mo2VCo钢的热处理工艺优化[J]. 金属热处理, 2022, 47(4): 133-140.
[15]	吕杰晟, 宋志刚, 何建国, 丰涵, 郑文杰, 朱玉亮. S32205双相不锈钢冷轧退火组织转变及强塑化机理分析[J]. 金属热处理, 2022, 47(4): 141-145.