热处理工艺对4Cr3Mo2Si1V钢组织与性能的影响

doi:10.13251/j.issn.0254-6051.2022.01.037

金属热处理 ›› 2022, Vol. 47 ›› Issue (1): 226-232.DOI: 10.13251/j.issn.0254-6051.2022.01.037

热处理工艺对4Cr3Mo2Si1V钢组织与性能的影响

蔡著文^1,2, 李玲^1,2, 沈俞涛^1,2, 吴晓春^1,2,3

1.上海大学省部共建高品质特殊钢冶金与制备国家重点实验室, 上海 200072;
2.上海大学材料科学与工程学院, 上海 200072;
3.上大鑫仑材料科技广东有限公司, 广东肇庆 526105

收稿日期:2021-08-13 修回日期:2021-10-24 出版日期:2022-01-25 发布日期:2022-02-18
通讯作者: 吴晓春,教授,博士生导师,E-mail:xcwu@staff.shu.edu.cn
作者简介:蔡著文(1996—),男,硕士研究生,主要研究方向为模具钢材料研发与应用,E-mail:johnczw@163.com。
基金资助:
国家重点研发计划(2016YFB0300400);广东省重点领域研发计划(2020B010184002);省部共建高品质特殊钢冶金与制备国家重点实验室自主课题(SKLASS2019-Z017)

Effect of heat treatment process on microstructure and properties of 4Cr3Mo2Si1V steel

Cai Zhuwen^1,2, Li Ling^1,2, Shen Yutao^1,2, Wu Xiaochun^1,2,3

1. State Key Laboratory of Advanced Special Steel, Shanghai University, Shanghai 200072, China;
2. College of Materials Science and Engineering, Shanghai University, Shanghai 200072, China;
3. Shangda Xinlun Material and Technology Guangdong Co.,Ltd., Zhaoqing Guangdong 526105, China

Received:2021-08-13 Revised:2021-10-24 Online:2022-01-25 Published:2022-02-18

摘要/Abstract

摘要： 利用热膨胀相变仪测定了新型热作模具钢4Cr3Mo2Si1V的奥氏体连续冷却转变(CCT)曲线,研究了其在不同淬火、回火工艺下的力学性能和显微组织。结果表明:4Cr3Mo2Si1V钢的珠光体与贝氏体的临界冷速分别为0.03 ℃·s^-1和0.8 ℃·s^-1。经淬火试验,发现该钢种在1030 ℃和1060 ℃油淬后具有较高的硬度,且晶粒未发生明显长大。随着回火温度的提高,其硬度呈现先增后降的趋势,在500 ℃回火时由于第二相粒子大量析出,析出强化作用增强,促使二次硬化现象产生,硬度达到峰值,约57 HRC。经过多组工艺对比后,发现1030 ℃淬火和600 ℃回火后的平均冲击吸收能量达到最大值,为265 J,且硬度值仍保持在52 HRC,故最终选定1030 ℃×30 min油淬+600 ℃×2 h回火两次作为4Cr3Mo2Si1V钢的最佳热处理工艺。

关键词: 热作模具钢, 合金化, CCT曲线, 热处理, 力学性能

Abstract: Continuous cooling transformation (CCT) diagram of hot work die steel 4Cr3Mo2Si1V was measured by thermal dilatometry. Mechanical properties and microstructure of the steel under different quenching and tempering processes were studied. The results show that the critical cooling rates of pearlite and bainite of the steel are 0.03 ℃·s^-1 and 0.8 ℃·s^-1, respectively. Through quenching test, it is found that the steel has high hardness after oil quenching at 1030 ℃ and 1060 ℃, and the grain size does not grow obviously. The hardness of the steel increases firstly and then decreases with the increase of tempering temperature, reaching peak value of about 57 HRC at 500 ℃ due to a high volume fraction and density of second phase particles precipitate which enhances the precipitation strengthening effect and results in the secondary hardening phenomenon. After quenching at 1030 ℃ and tempering at 600 ℃, the average impact absorbed energy of the steel reaches the maximum value of 265 J, as well as the hardness remains 52 HRC. By evaluating the combination of strength and toughness, the optimal heat treatment process of the 4Cr3Mo2Si1V steel is quenching at 1030 ℃ for 30 min with oil cooling and then tempering twice at 600 ℃ for 2 h with air cooling.

Key words: hot work die steel, alloying, CCT curve, heat treatment, mechanical properties

中图分类号:

TG142.1

蔡著文, 李玲, 沈俞涛, 吴晓春. 热处理工艺对4Cr3Mo2Si1V钢组织与性能的影响[J]. 金属热处理, 2022, 47(1): 226-232.

Cai Zhuwen, Li Ling, Shen Yutao, Wu Xiaochun. Effect of heat treatment process on microstructure and properties of 4Cr3Mo2Si1V steel[J]. Heat Treatment of Metals, 2022, 47(1): 226-232.

参考文献

[1]吴晓春, 左鹏鹏. 国内外热作模具钢发展现状与趋势[J]. 模具工业, 2013, 39(10): 1-9.
Wu Xiaochun, Zuo Pengpeng. Development status and trend of hot working die steels at home and abroad[J]. Die and Mould Industry, 2013, 39(10): 1-9.
[2]施雯, 刘以宽. QRO 90 Supreme热作模具钢的性能研究[J]. 机械工程材料, 1996(6): 27-29, 42.
Shi Wen, Liu Yikuan. An investigation on properties of QRO 90 Supreme hot working die steel[J]. Materials for Mechanical Engineering, 1996(6): 27-29, 42.
[3]王小军, 徐明纲, 陈秋龙, 等. 热作模具钢QRO90与8407(H13)回火稳定性对比研究[J]. 上海金属, 1998(2): 8-11.
Wang Xiaojun, Xu Minggang, Chen Qiulong, et al. Research on the tempering stability of die steel for hot working: QRO90 and 8404(H13)[J]. Shanghai Metals, 1998(2): 8-11.
[4]Michaud P, Delagnes D, Lamesle P, et al. The effect of the addition of alloying elements on carbide precipitation and mechanical properties in 5% chromium martensitic steels[J]. Acta Materialia, 2007, 55(14): 4877-4889.
[5]张金祥, 欧阳希, 周健, 等. Cr含量降低对H13钢组织与力学性能的影响[J]. 材料导报, 2018, 32(8): 1323-1327, 1343.
Zhang Jinxiang, Ouyang Xi, Zhou Jian, et al. Study on microstructure and mechanical properties of H13 tool steel after chromium content reduction[J]. Materials Review, 2018, 32(8): 1323-1327, 1343.
[6]Kim B, Celada C, Martín D S, et al. The effect of silicon on the nanoprecipitation of cementite[J]. Acta Materialia, 2013, 61(18): 6983-6992.
[7]Sourmail T, Millot M M. Thermal and mechanical stability of retained austenite in 1C bearing steels with varying Si contents[J]. Materials Science and Technology, 2016, 32(11): 1126-1132.
[8]刘曼, 徐光, 田俊羽, 等. 硅含量对低碳贝氏体相变动力学和性能的影响[J]. 钢铁研究学报, 2019, 31(11): 982-987.
Liu Man, Xu Guang, Tian Junyu, et al. Effect of Si content on kinetics of bainitic transformation and properties of low carbon bainite steels[J]. Journal of Iron and Steel Research. 2019, 31(11): 982-987.
[9]金欣, 周健, 迟宏宵, 等. Mo-W-Co系高热强性热锻模具钢的组织与性能[J]. 金属热处理, 2018, 43(2): 8-15.
Jin Xin, Zhou Jian, Chi Hongxiao, et al. Microstructure and mechanical properties of Mo-W-Co high hot-strength hot-work die steels[J]. Heat Treatment of Metals, 2018, 43(2): 8-15.
[10]殷军伟, 周健, 蒋业华, 等. 热处理工艺对5Cr5Mo2V钢组织与性能的影响[J]. 金属热处理, 2021, 46(2): 55-60.
Yin Junwei, Zhou Jian, Jiang Yehua, et al. Effect of heat treatment process on microstructure and properties of 5Cr5Mo2V steel[J]. Heat Treatment of Metals, 2021, 46(2): 55-60.
[11]陈英伟, 吴晓春, 宋雯雯, 等. 含铌热作模具钢中碳化物的演变对热稳定性的影响[J]. 材料热处理学报, 2010, 31(5): 75-80.
Chen Yingwei, Wu Xiaochun, Song Wenwen, et al. Effect of carbide evolution on thermal-stability in Nb-microalloyed hot work steel[J]. Transactions of Materials and Heat Treatment, 2010, 31(5): 75-80.
[12]高海龙. 新型3%Cr热作模具钢组织与力学性能研究[D]. 西安: 西安建筑科技大学, 2017.
Gao Hailong. Study on microstructure and mechanical properties of new 3%Cr hot work die steel[D]. Xi'an: Xi'an University of Architecture and Technology, 2017.
[13]万霄, 陈瑞航, 王颜, 等. 热处理工艺对H13热作模具钢组织与性能的影响[J]. 宽厚板, 2020, 26(5): 18-22.
Wan Xiao, Chen Ruihang, Wang Yan, et al. Effects of heat treatment process on microstructure and properties of H13 hot-working die steel[J]. Wide and Heavy Plate, 2020, 26(5): 18-22.
[14]Souki I, Delagnes D, Lours P. Influence of heat treatment on the fracture toughness and crack propagation in 5% Cr martensitic steel[J]. Procedia Engineering, 2011(10): 631-637.

[1]	梁恩溥, 徐乐, 杨勇, 王毛球. 添加Al、Cu对40CrNi3MoV钢组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 17-23.
[2]	祁晓亮, 李岩, 定巍, 赵增武. 含Al中锰TRIP钢原始组织对临界退火后组织与力学性能的影响[J]. 金属热处理, 2022, 47(4): 24-29.
[3]	陈保安, 张静媛, 祝志祥, 韩钰, 潘学东, 张磊, 陈素红. 化学成分对高强Al-Mg-Si合金组织和性能的影响[J]. 金属热处理, 2022, 47(4): 30-38.
[4]	陈连生, 张露友, 田亚强, 杨子旋, 李红斌, 潘红波, 魏英立. 低碳高强舰船用钢的CCT曲线及其组织性能[J]. 金属热处理, 2022, 47(4): 63-68.
[5]	王云龙, 余伟, 张昳, 史佳新, 李明辉. 奥氏体化温度对贝氏体钢等温转变及力学性能的影响[J]. 金属热处理, 2022, 47(4): 80-85.
[6]	骆再斌, 范子泽, 彭振. 轻质高熵合金的研究进展[J]. 金属热处理, 2022, 47(4): 100-107.
[7]	李立, 曾艳, 吴晓春. 4Cr5Mo2VCo钢的热处理工艺优化[J]. 金属热处理, 2022, 47(4): 133-140.
[8]	吕杰晟, 宋志刚, 何建国, 丰涵, 郑文杰, 朱玉亮. S32205双相不锈钢冷轧退火组织转变及强塑化机理分析[J]. 金属热处理, 2022, 47(4): 141-145.
[9]	王琪, 吴光亮. 回火温度对1100 MPa级高强钢组织与性能的影响[J]. 金属热处理, 2022, 47(4): 146-150.
[10]	于洪军, 程福超, 马泽天, 王永金, 陈俊豪, 陈正家, 宋传颂馨. 不同水韧处理工艺下铌微合金化高锰钢的组织演变和力学性能[J]. 金属热处理, 2022, 47(4): 151-154.
[11]	张骥俊, 邢彦锋, 曹菊勇. 超声振动对CMT电弧增材制造铝合金组织与性能的影响[J]. 金属热处理, 2022, 47(4): 159-164.
[12]	刘文彬, 乔龙阳, 潘新宇, 程格, 李爱娜, 裴新军. 淬火温度对刀剪用M390粉末冶金不锈钢组织和性能的影响[J]. 金属热处理, 2022, 47(4): 189-195.
[13]	王瑞琴, 葛鹏, 廖强, 侯鹏, 刘宇. 固溶冷却方式对短时用高温钛合金板材组织和性能的影响[J]. 金属热处理, 2022, 47(4): 196-198.
[14]	王方军, 王东哲, 万红, 时瑶, 沈涛. 热处理和冷变形量对定膨胀合金4J32C线膨胀系数的影响[J]. 金属热处理, 2022, 47(4): 199-203.
[15]	王绍灼, 孟晗, 王芬, 樊海卫, 李燕, 唐超. 改善低氧TC4-LC及重熔TC4钛合金性能的热处理工艺[J]. 金属热处理, 2022, 47(4): 204-207.

热处理工艺对4Cr3Mo2Si1V钢组织与性能的影响

Effect of heat treatment process on microstructure and properties of 4Cr3Mo2Si1V steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价