退火温度对高轧制延展率Al/IF钢多层复合材料力学性能的影响

doi:10.13251/j.issn.0254-6051.2022.01.042

摘要/Abstract

摘要： 采用叠轧焊接方法制备Al/IF钢多层复合材料,随后进行300~450 ℃退火处理,并对叠轧态和退火态的微观结构及力学性能进行分析。结果表明:叠轧态Al/IF钢多层复合材料的抗拉强度介于纯Al和IF钢之间,断裂总延伸率相对较低,退火后Al和IF钢层的硬变均高于其原材料;随着退火温度的增加,抗拉强度逐渐降低,断裂总延伸率呈先增加后减小的趋势,在350 ℃退火时,复合材料的综合力学性能最优。退火温度对Al/IF钢多层复合材料力学性能的影响主要体现在对Al层的影响上。

关键词: 叠轧焊接, 退火, 多层复合材料, 力学性能

Abstract: Al/IF steel multilayer composites were prepared by roll-bonding, and then annealed at 300-450 ℃. The microstructure and mechanical properties of the as-rolled and as-annealed Al/IF steel multilayer composites were analyzed. The results show that the tensile strength of the roll-bonded Al/IF steel multilayer composites is between that of pure Al and IF steel, and the total extension at fracture is relatively low, while the hardness of botn Al layer and IF steel layer after annealing are higher than that of raw mateial. As the annealing temperature increases, the tensile strength gradually decreases, and the total extension at fracture increases first and then decreases. When annealed at 350 ℃, the comprehensive mechanical properties of the composites are the best. The effect of annealing temperature on the mechanical properties of the Al/IF steel multilayer composites is mainly reflected in the effect on the Al layer.

Key words: roll-bonding, annealing treatment, multilayer composites, mechanical properties

中图分类号:

TB331

王鸣, 李文锦, 张旭, 程丽丽, 徐洋. 退火温度对高轧制延展率Al/IF钢多层复合材料力学性能的影响[J]. 金属热处理, 2022, 47(1): 255-260.

Wang Ming, Li Wenjin, Zhang Xu, Cheng Lili, Xu Yang. Effect of annealing temperature on mechanical properties of Al/IF steel multilayer composites with high rolling ductility[J]. Heat Treatment of Metals, 2022, 47(1): 255-260.

参考文献

[1]王涛, 齐艳阳, 刘江林, 等. 金属层合板轧制复合工艺国内外研究进展[J]. 哈尔滨工业大学学报, 2020, 52(6): 42-56.
Wang Tao, Qi Yanyang, Liu Jianglin, et al. Research progress of metal laminates roll bonding process at home and abroad[J]. Journal of Harbin Institute of Technology, 2020, 52(6): 42-56.
[2]黎旭, 冯中学, 史庆南. 钛-钢复合材料制备技术及性能研究进展[J]. 稀有金属, 2018, 42(10): 1103-1113.
Li Xu, Feng Zhongxue, Shi Qingnan, et al. Progress in preparation technology and properties of titanium-steel composites[J]. Chinese Journal of Rare Metals, 2018, 42(10): 1103-1113.
[3]Hsieh P J, Hung Y P, Huang J C. Transformation into nano-crystalline or amorphous materials in Zr-X binary systems using ARB route[J]. Scripta Materialia, 2003, 49(2): 173-178.
[4]周生刚, 王涛, 孙丽达. 金属层状复合材料的研究现状[J]. 热加工工艺, 2016, 45(10): 15-20.
Zhou Shenggang, Wang Tao, Sun Lida, et al. Research status of metal laminar composite[J]. Hot Working Technology, 2016, 45(10): 15-20.
[5]陈连生, 张鑫磊, 郑小平, 等. 轧制双金属复合板材的研究现状[J]. 稀有金属材料与工程, 2018, 47(10): 3243-3250.
Chen Liansheng, Zhang Xinlei, Zheng Xiaoping, et al. Research status of bimetal laminated composite plate prepared by rolling process[J]. Rare Metal Materials and Engineering, 2018, 47(10): 3243-3250.
[6]Takahashi Y, Inoue K, Nishiguchi K. Identification of void shrinkage mechanisms[J]. Acta Metallurgica et Materialia, 1993, 41(11): 3077-3084.
[7]刘国平, 王渠东, 蒋海燕. 铜/铝双金属复合材料研究新进展[J]. 材料导报, 2020, 34(7): 7115-7122.
Liu Guoping, Wang Qudong, Jiang Haiyan, et al. New research progress on copper/aluminum bimetallic composites[J]. Materials Reports, 2020, 34(7): 7115-7122.
[8]徐圣航, 周承商, 刘咏. 金属-金属层状结构复合材料研究进展[J]. 中国有色金属学报, 2019, 29(6): 1125-1142.
Xu Shenghang, Zhou Chengshang, Liu Yong, et al. Research progress in metal-metal laminated structural composites[J]. The Chinese Journal of Nonferrous Metals, 2019, 29(6): 1125-1142.
[9]邓斌, 刘文磊, 王博, 等. 某新型商用车复合材料板簧轻量化研究[J]. 汽车实用技术, 2021, 46(17): 88-90.
Deng Bin, Liu Wenlei, Wang Bo, et al. Light weight research on composite leaf spring of a new commercial vehicle[J]. Automobile Applied Technology, 2021, 46(17): 88-90.
[10]Kumar R V, Keshavamurthy R, Perugu C S, et al. Influence of hot rolling on friction and wear behaviour of Al6061-ZrB2 in-situ metal matrix composites[J]. Journal of Manufacturing Processes, 2021, 69: 473-490.
[11]于化顺. 金属基复合材料及其制备技术[M]. 北京: 化学工业出版社, 2006.
[12]张志娟, 张兵, 赵田丽, 等. 轧制三金属复合材料研究进展[J]. 精密成形工程, 2021, 13(6): 23-34.
Zhang Zhijuan, Zhang Bing, Zhao Tianli, et al. Research progress of tri-metal composites prepared by rolling process[J]. Journal of Netshape Forming Engineering, 2021, 13(6): 23-34.
[13]吴昊, 熊桑, 张渤, 等. 冷轧参数对铜/钢复合板结合情况的影响[J]. 塑性工程学报, 2021, 28(8): 75-82.
Wu Hao, Xiong Sang, Zhang Bo, et al. Influence of cold rolling parameters on bonding of copper/steel clad plate[J]. Journal of Plasticity Engineering, 2021, 28(8): 75-82.
[14]崔玉豪, 曹远奎, 李娜, 等. Ti-Cu-Mo层状复合材料的轧制行为与力学性能[J]. 粉末冶金材料科学与工程, 2021, 26(4): 346-354.
Cui Yuhao, Cao Yuankui, Li Na, et al. Rolling behavior and mechanical properties of Ti-Cu-Mo laminated composites[J]. Materials Science and Engineering of Powder Metallurgy, 2021, 26(4): 346-354.
[15]崔岩, 彭喜英, 李新靓, 等. Ni/Al复合材料在累积叠轧制备过程中的组织演变和力学分析[J]. 材料热处理学报, 2020, 41(6): 1-6.
Cui Yan, Peng Xiying, Li Xinliang, et al. Microstructure evolution and mechanical analysis of Ni/Al composites during preparation of accumulative roll bonding (ARB)[J]. Transactions of Materials and Heat Treatment, 2020, 41(6): 1-6.
[16]崔岩, 王利成, 董常青, 等. 累积叠轧制备Ni/Al多层复合材料[J]. 热加工工艺, 2019, 48(24): 78-80.
Cui Yan, Wang Licheng, Dong Changqing, et al. Preparation of Ni/Al multilayer composites by accumulative roll bonding[J]. Hot Working Technology, 2019, 48(24): 78-80.
[17]王秋雨, 张兵, 赵田丽, 等. 轧制复合制备TA1/AZ31B/TA1层状复合材料组织与性能研究[J]. 重型机械, 2019, 5(3): 22-28.
Wang Qiuyu, Zhang Bing, Zhao Tianli, et al. Study on microstructure and properties of TA1/AZ31B/TA1 laminated composites produced by roll bonding[J]. Heavy Machinery, 2019, 5(3): 22-28.
[18]Mojtaba D, Fathallah Q, Mahdi G, et al. Effect of inter-cycle heat treatment in accumulative roll-bonding (ARB) process on planar isotropy of mechanical properties of AA1050 sheets[J]. Transactions of Nonferrous Metals Society of China, 2020, 30(9): 2381-2393.
[19]Adnan I, Khdair A Fathy. Enhanced strength and ductility of Al-SiC nanocomposites synthesized by accumulative roll bonding[J]. Journal of Materials Research and Technology, 2020, 9(1): 478-489.
[20]李小兵, 蒋国民, 王强, 等. 钢/铝层状复合板的拉伸力学性能与界面失效过程[J]. 中国有色金属学报, 2021, 31(8): 2125-2135.
Li Xiaobing, Jiang Guomin, Wang Qiang, et al. Mechanical properties and interface failure behavior of steel/Al laminated composite sheets during tensile test[J]. The Chinese Journal of Nonferrous Metals, 2021, 31(8): 2125-2135.
[21]冯菲玥, 陈云霞. 铝/钢异种金属焊接技术的研究现状[J]. 焊接技术, 2021, 50(1): 1-8.
Feng Feiyue, Chen Yunxia. A review of the research on aluminum/steel dissimilar metal welding techniques[J]. Welding Technology, 2021, 50(1): 1-8.
[22]高勃兴, 邹德坤, 谢红飙, 等. 铝/钢轧制复合有限元二次开发模拟与实验研究[J]. 精密成形工程, 2021, 13(6): 56-63.
Gao Boxing, Zou Dekun, Xie Hongbiao, et al. Simulation and experimental study on finite element secondary development of aluminum/steel rolling composite[J]. Journal of Netshape Forming Engineering, 2021, 13(6): 56-63.
[23]陈大林. 铝钢异种金属焊接研究现状[J]. 兰州石化职业技术学院学报, 2021, 21(1): 21-25.
Chen Dalin. Research status of aluminum steel dissimilar metals welding[J]. Journal of Lanzhou Petrochemical Polytechnic, 2021, 21(1): 21-25.
[24]Kévin V, Laurent P, Anne L H, et al. Magnetic shielding at low frequencies: Application for an aluminum/steel composite elaborated by accumulative roll bonding[J]. Advanced Engineering Materials, 2019, 21(4): 1-8.
[25]Fu L, Xiao H, Yu C, et al. Bonding enhancement of cold rolling Al/steel composite plates via self-nano film modification[J]. Journal of Materials Processing Technology, 2022, 72(5): 300-312.
[26]Clérico P, Mininger X, Prévond L, et al. Compromise between magnetic shielding and mechanical strength of thin Al/steel/Al sandwiches produced by cold roll bonding: Experimental and numerical approaches[J]. Journal of Alloys and Compounds, 2019, 59(5): 798-825.
[27]Milad T, Mostafa A. Manufacturing Al/steel multilayered composite by accumulative roll bonding and the effects of subsequent annealing on the microstructural and mechanical characteristics[J]. Materials Science and Engineering A, 2014, 590: 186-193.
[28]王鸣, 王杰, 赵杰, 等. 退火温度对08Al冷轧板力学性能的影响[J]. 材料热处理学报, 2015, 36(S1): 107-110.
Wang Ming, Wang Jie, Zhao Jie, et al. Effect of annealing temperature on mechanical properties of 08Al cold-rolled sheet[J]. Transactions of Materials and Heat Treatment, 2015, 36(S1): 107-110.
[29]王鸣, 张旭, 赵阳, 等. 轧制延展率对IF钢箔力学性能的影响[J]. 材料导报, 2020, 34(2): 1395-1406.
Wang Ming, Zhang Xu, Zhao Yang, et al. Effect of rolling elongation on the mechanical properties of IF steel foil[J]. Materials Reports, 2020, 34(2): 1395-1406.
[30]吴圣川, 李存海, 张文, 等. 金属材料疲劳裂纹扩展机制及模型的研究进展[J]. 固体力学学报, 2019, 40(6): 489-538.
Wu Shengchuan, Li Cunhai, Zhang Wen, et al. Recent research progress on mechanisms and models of fatigue crack growth for metallic materials[J]. Chinese Journal of Solid Mechanics, 2019, 40(6): 489-538.