临界区回火温度对Fe-4Mn-1.2Cr-0.3Cu-0.6Ni中锰钢微观组织和力学性能的影响

doi:10.13251/j.issn.0254-6051.2022.02.017

金属热处理 ›› 2022, Vol. 47 ›› Issue (2): 91-98.DOI: 10.13251/j.issn.0254-6051.2022.02.017

临界区回火温度对Fe-4Mn-1.2Cr-0.3Cu-0.6Ni中锰钢微观组织和力学性能的影响

刘韬, 吴红艳, 高秀华, 秦岽烊, 杜林秀

东北大学轧制技术及连轧自动化国家重点实验室, 辽宁沈阳 110819

收稿日期:2021-10-12 修回日期:2021-12-13 出版日期:2022-02-25 发布日期:2022-04-01
通讯作者: 杜林秀,教授,博士生导师,E-mail: dulx@ral.neu.edu.cn
作者简介:刘韬(1994—),男,硕士,主要研究方向为中锰钢的组织性能,E-mail:2438803940@qq.com。
基金资助:
国家高技术研究发展计划(863计划)(2015AA03A501)

Effect of intercritical tempering temperature on microstructure and mechanical properties of Fe-4Mn-1.2Cr-0.3Cu-0.6Ni medium manganese steel

Liu Tao, Wu Hongyan, Gao Xiuhua, Qin Dongyang, Du Linxiu

State Key Laboratory of Rolling and Automation, Northeastern University, Shenyang Liaoning 110819, China

Received:2021-10-12 Revised:2021-12-13 Online:2022-02-25 Published:2022-04-01

摘要/Abstract

摘要： 研究了临界区回火温度对Fe-4Mn-1.2Cr-0.3Cu-0.6Ni中锰钢组织与力学性能的影响。通过热轧后直接淬火+临界区回火的工艺制备试验钢。采用光学显微镜(OM)、电子探针显微分析仪(EPMA)的扫描功能、透射电镜(TEM)、拉伸试验及冲击试验等对轧后淬火态和回火态试验钢的显微组织及力学性能进行了表征。结果表明,试验钢热轧后淬火可获得较高位错密度的板条马氏体,经过临界区回火后获得在回火马氏体基体上分布残留奥氏体的复合组织。随着临界区回火温度的升高,试验钢的抗拉强度呈升高趋势,而屈服强度先下降后增加,伸长率的变化趋势与试验钢中的残留奥氏体含量相关,冲击性能随临界区回火温度的升高呈先升高后降低的趋势。630 ℃回火后试验钢的拉伸性能最佳,650 ℃回火后试验钢的冲击性能最佳,确定最佳临界区回火温度区间为630~650 ℃。

关键词: 中锰钢, 残留奥氏体, TRIP效应, 临界区回火, 力学性能

Abstract: Effect of intercritical tempering temperature on microstructure and mechanical properties of Fe-4Mn-1.2Cr-0.3Cu-0.6Ni medium manganese steel was studied. The tested steel was prepared by direct quenching after hot rolling and intercritical tempering. The microstructure and mechanical properties of the quenched after rolling and tempered tested steels were characterized by means of optical microscope (OM), scanning function of electron probe microanalyzer (EPMA), transmission electron microscope (TEM), tensile test and impact test. The results show that the lath martensite with higher dislocation density can be obtained in the tested steel quenched after hot rolling, and the composite structure of retained austenite distributed on the tempered martensite matrix can be formed after intercritical tempering. With the increase of intercritical tempering temperature, the tensile strength of the tested steel increases, while the yield strength first decreases and then increases. The change trend of elongation is related to the content of retained austenite in the tested steel. The impact property first increases and then decreases with the increase of intercritical tempering temperature. The tensile properties of the tested steel tempered at 630 ℃ is the best, but the impact property of the tested steel tempered at 650 ℃ is the best, so that the optimum intercritical tempering temperature range is determined to be 630-650 ℃.

Key words: medium manganese steel, retained austenite, TRIP effect, intercritical tempering, mechanical properties

中图分类号:

TG146.2

刘韬, 吴红艳, 高秀华, 秦岽烊, 杜林秀. 临界区回火温度对Fe-4Mn-1.2Cr-0.3Cu-0.6Ni中锰钢微观组织和力学性能的影响[J]. 金属热处理, 2022, 47(2): 91-98.

Liu Tao, Wu Hongyan, Gao Xiuhua, Qin Dongyang, Du Linxiu. Effect of intercritical tempering temperature on microstructure and mechanical properties of Fe-4Mn-1.2Cr-0.3Cu-0.6Ni medium manganese steel[J]. Heat Treatment of Metals, 2022, 47(2): 91-98.

参考文献

[1]Javaherdashti R. How corrosion affects industry and life[J]. Anti-Corrosion Methods and Materials, 2000, 47(1): 30-34.
[2]De L F D, Díaz I, Simancas J, et al. Long-term atmospheric corrosion of mild steel[J]. Corrosion Science, 2011, 53: 604-617.
[3]Townsend H E. Effects of alloying elements on the corrosion of steel in industrial atmospheres[J]. Corrosion, 2001, 57(6): 499-501.
[4]陈新华. 合金元素对经济耐候钢大气腐蚀协同抑制作用[D]. 沈阳: 中科院金属研究所, 2007.
Chen Xinhua. Synergistic effect of alloying elements on the resistance to atmospheric corrosion of cost effective weathering steel[D]. Shenyang: Institute of Metal Research Chinese Academy of Sciences, 2007.
[5]松岛岩. 低合金耐蚀钢—开发、发展及研究[M]. 靳裕康, 译. 北京: 冶金工业出版社, 2004: 12.
[6]Montoya P, Díaz I, Granizo N, et al. A study on accelerated corrosion testing of weathering steel[J]. Materials Chemistry and Physics, 2013, 142: 220-228.
[7]苏冠桥. 海洋平台用高强韧中锰钢组织性能控制及腐蚀行为研究[D]. 沈阳: 东北大学, 2015.
Su Guanqiao. Study on the regulation of microstructure & mechanical properties and corrosion behavior of medium manganese steel with high strength and high toughness for offshore platform at seawater environment[D]. Shenyang: Northeastern University, 2015.
[8]Li Z C, Misra R D K, Cai Z H, et al. Mechanical properties and deformation behavior in hot-rolled 0.2C-1.5/3Al-8.5Mn-Fe TRIP steel: The discontinuous TRIP effect[J]. Materials Science and Engineering A, 2016, 673: 63-72.
[9]Xu Y B, Zou Y, Hu Z P, et al. Correlation between deformation behavior and austenite characteristics in a Mn-Al type TRIP steel[J]. Materials Science and Engineering A, 2017, 698: 126-135.
[10]董俊华, 艾美蓉, 韩恩厚, 等. Mn-Cu耐候钢锈层结构与性能关系研究[C]//中国腐蚀与防护学会第十一届耐蚀金属材料学术年会论文集. 2008: 113-115.
[11]Qin D Y, Gao X H, Liu T, et al. Effect of annealing process on microstructure and mechanical properties in microalloyed medium manganese steel[J]. Steel Research International, 2021, 92(4): 2000517.
[12]王昌, 徐海峰, 黄崇湘, 等. 中锰钢逆相变退火组织的演变及锰的配分行为[J]. 钢铁研究学报, 2016, 28(4): 38-46.
Wang Chang, Xu Haifeng, Huang Chongxiang, et al. Evolution of ART-annealed microstructure and partition behavior of manganese in medium mangenese steel[J]. Journal of Iron and Steel Research, 2016, 28(4): 38-46.
[13]朱瑞富, 朝志强, 魏涛, 等. 奥氏体中锰钢加工硬化的微观机制[J]. 钢铁研究学报, 1997, 9(1): 30-33.
Zhu Ruifu, Chao Zhiqiang, Wei Tao, et al. Microscopic mechanism of work hardening of austenitic medium manganese steel[J]. Journal of Iron and Steel Research, 1997, 9(1): 30-33.
[14]沈国慧. 新型超高强韧中锰钢组织、力学性能及防弹性研究[D]. 北京: 北京科技大学, 2021.
Shen Guohui. Studies on microstructure, mechanical properties and ballistic performance of novel medium-Mn steel possessing ultrahigh strength and high toughness[D]. Beijing: University of Science and Technology Beijing, 2021.
[15]邵成伟. 高强塑积含铝中锰钢组织调控及氢脆敏感性研究[D]. 北京: 北京交通大学, 2018.
Shao Chengwei. Study on microstructure control and hydrogen embrittlement susceptibility of Al-Containing medium Mn steels with high product of strength to ductility[D]. Beijing: Beijing Jiaotong University, 2018.
[16]吝章国, 唐荻, 江海涛, 等. 淬火温度对中锰Q&P钢组织与性能的影响[J]. 金属热处理, 2016, 41(10): 123-127.
Lin Zhangguo, Tang Di, Jiang Haitao, et al. Effect of quenching temperature on microstructure and properties of medium-manganese Q＆P steel[J]. Heat Treatment of Metals, 2016, 41(10): 123-127.
[17]Cai Z H, Ding H, Misra R D K, et al. Austenite stability and deformation behavior in a cold-rolled transformation-induced plasticity steel with medium manganese content[J]. Acta Materialia, 2015, 84: 229-236.
[18]Cai Z H, Ding H, Xue X, et al. Significance of control of austenite stability and three-stage work-hardening behavior of an ultrahigh strength-high ductility combination transformation-induced plasticity steel[J]. Scripta Materialia, 2013, 68(11): 865-868.
[19]Sun C, Liu S L, Misra R D K, et al. Influence of intercritical tempering temperature on impact toughness of a quenched and tempered medium-Mn steel: Intercritical tempering versus traditional tempering[J]. Materials Science and Engineering A, 2018, 711: 484-491.
[20]田亚强, 黎旺, 郑小平, 等. 两相区形变对中锰钢逆相奥氏体稳定性及其断裂性能的影响[J]. 金属热处理, 2019, 44(5): 43-48.
Tian Yaqiang, Li Wang, Zheng Xiaoping, et al. Effect of intercritical deformation on reversed austenite stability of medium manganese steel and its fracture properties[J]. Heat Treatment of Metals, 2019, 44(5): 43-48.
[21]蔡志辉. 高强塑性中锰钢的组织演变及力学性能的研究[D]. 沈阳: 东北大学, 2014.
Cai Zhihui. Study on microstructural evolution and mechanical properties of medium manganese steels with superior strength and ductility[D]. Shenyang: Northeastern University, 2014.
[22]邹英. 超低碳中锰钢板的组织性能调控及强韧化机理[D]. 沈阳: 东北大学, 2019.
Zou Ying. Microstructure-properties regulation and strengthening-toughening mechanism of ultra-low carbon medium manganese steel plate[D]. Shenyang: Northeastern University, 2019.
[23]沈鑫珺. 轧制与水冷耦合的控制轧制技术研究[D]. 沈阳: 东北大学, 2017.
Shen Xinjun. Study of rolling and water-cooling coupled control rolling process[D]. Shenyang: Northeastern University, 2017.

临界区回火温度对Fe-4Mn-1.2Cr-0.3Cu-0.6Ni中锰钢微观组织和力学性能的影响

Effect of intercritical tempering temperature on microstructure and mechanical properties of Fe-4Mn-1.2Cr-0.3Cu-0.6Ni medium manganese steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	梁恩溥, 徐乐, 杨勇, 王毛球. 添加Al、Cu对40CrNi3MoV钢组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 17-23.
[2]	祁晓亮, 李岩, 定巍, 赵增武. 含Al中锰TRIP钢原始组织对临界退火后组织与力学性能的影响[J]. 金属热处理, 2022, 47(4): 24-29.
[3]	陈保安, 张静媛, 祝志祥, 韩钰, 潘学东, 张磊, 陈素红. 化学成分对高强Al-Mg-Si合金组织和性能的影响[J]. 金属热处理, 2022, 47(4): 30-38.
[4]	陈连生, 张露友, 田亚强, 杨子旋, 李红斌, 潘红波, 魏英立. 低碳高强舰船用钢的CCT曲线及其组织性能[J]. 金属热处理, 2022, 47(4): 63-68.
[5]	王云龙, 余伟, 张昳, 史佳新, 李明辉. 奥氏体化温度对贝氏体钢等温转变及力学性能的影响[J]. 金属热处理, 2022, 47(4): 80-85.
[6]	骆再斌, 范子泽, 彭振. 轻质高熵合金的研究进展[J]. 金属热处理, 2022, 47(4): 100-107.
[7]	吕杰晟, 宋志刚, 何建国, 丰涵, 郑文杰, 朱玉亮. S32205双相不锈钢冷轧退火组织转变及强塑化机理分析[J]. 金属热处理, 2022, 47(4): 141-145.
[8]	王琪, 吴光亮. 回火温度对1100 MPa级高强钢组织与性能的影响[J]. 金属热处理, 2022, 47(4): 146-150.
[9]	张骥俊, 邢彦锋, 曹菊勇. 超声振动对CMT电弧增材制造铝合金组织与性能的影响[J]. 金属热处理, 2022, 47(4): 159-164.
[10]	刘文彬, 乔龙阳, 潘新宇, 程格, 李爱娜, 裴新军. 淬火温度对刀剪用M390粉末冶金不锈钢组织和性能的影响[J]. 金属热处理, 2022, 47(4): 189-195.
[11]	王瑞琴, 葛鹏, 廖强, 侯鹏, 刘宇. 固溶冷却方式对短时用高温钛合金板材组织和性能的影响[J]. 金属热处理, 2022, 47(4): 196-198.
[12]	王绍灼, 孟晗, 王芬, 樊海卫, 李燕, 唐超. 改善低氧TC4-LC及重熔TC4钛合金性能的热处理工艺[J]. 金属热处理, 2022, 47(4): 204-207.
[13]	陈强, 陈林芳, 杨明华. 18CrNiMo7-6钢的可控气氛高温渗碳工艺[J]. 金属热处理, 2022, 47(4): 231-239.
[14]	刘乃瑜, 曹磊, 郑少梅. 不同沉积温度下CrCN涂层的力学性能[J]. 金属热处理, 2022, 47(4): 240-244.
[15]	陈连生, 房宁, 曹仲乾, 杨子旋, 李红斌, 潘红波, 田亚强. 压下率对两相区温轧淬火配分中锰钢组织性能的影响[J]. 金属热处理, 2022, 47(3): 28-33.