铸态Ti-20Zr-10Nb-xMo合金的微观组织和耐腐蚀性能

doi:10.13251/j.issn.0254-6051.2022.03.028

金属热处理 ›› 2022, Vol. 47 ›› Issue (3): 147-150.DOI: 10.13251/j.issn.0254-6051.2022.03.028

铸态Ti-20Zr-10Nb-xMo合金的微观组织和耐腐蚀性能

张曼雪¹, 景然^1,2, 张雄¹, 张晴¹, 吴倩¹, 刘以柔¹

1.陕西理工大学材料科学与工程学院, 陕西汉中 723001;
2.陕西理工大学矿渣综合利用环保技术国家与地方联合工程实验室, 陕西汉中 723001

收稿日期:2021-11-29 修回日期:2022-01-19 出版日期:2022-03-25 发布日期:2022-04-22
通讯作者: 景然,副教授,博士,E-mail: qwe_jr@163.com
作者简介:张曼雪(1996—),女,硕士研究生,主要研究方向为钛合金强韧化,E-mail: zmxwbj@163.com。
基金资助:
国家自然科学基金(51701111);陕西省自然科学基础研究计划(2019JQ-881);陕西理工大学矿渣综合利用环保技术国家地方联合工程实验室开放基金(SLGPT2019KF01-07)

Microstructure and corrosion resistance of as-cast Ti-20Zr-10Nb-xMo alloys

Zhang Manxue¹, Jing Ran^1,2, Zhang Xiong¹, Zhang Qing¹, Wu Qian¹, Liu Yirou¹

1. School of Materials Science and Engineering, Shaanxi University of Technology, Hanzhong Shaanxi 723001, China;
2. National & Local Joint Engineering Laboratory for Slag Comprehensive Utilization and Environmental Technology, Shaanxi University of Technology, Hanzhong Shaanxi 723001, China

Received:2021-11-29 Revised:2022-01-19 Online:2022-03-25 Published:2022-04-22

摘要/Abstract

摘要： 采用X射线衍射仪(XRD)、光学显微镜(OM)、硬度测试、压缩试验和电化学工作站等研究了Mo含量对Ti-20Zr-10Nb-xMo(x=0,3,6,9,wt%)合金相结构、显微组织、力学性能以及电化学腐蚀性能的影响。结果表明,随着Mo含量的增加,Ti-20Zr-10Nb-xMo合金的相结构发生了α′+β→α″+β→β的变化,平均晶粒尺寸亦随着Mo含量的增加而逐渐降低;当Mo含量为9%时,合金的平均晶粒尺寸约为45 μm。通过Mo的添加,合金的抗压强度和屈服强度呈现先降低后升高的趋势,而显微硬度则先增大后降低;当Mo含量为9%时,合金的抗压强度最大,为1610 MPa,压缩应变为50.9%。未添加Mo的试验合金的自腐蚀电流密度最小,为33.19 nA·cm^-2,R_p值最大,为1531.52 kΩ·cm²,其耐腐蚀性最好。

关键词: 钛合金, 相结构, 显微组织, 力学性能, 腐蚀行为

Abstract: Effect of Mo content on microstructure, phase composition, mechanical properties and corrosion resistance of as-cast Ti-20Zr-10Nb-xMo alloys (x=0,3,6,9,wt%) was studied by means of X-ray diffraction, optical microscope, microhardness test, compressive test and electrochemical workstation. The results show that with the increase of Mo content, the phase structure of Ti-20Zr-10Nb-xMo alloys obviously changes from α′+β→α″+β→β, and the average grain size decreases gradually with the increase of Mo content. When the Mo content is 9%,the average grain size of the alloy is about 45 μm. With the addition of Mo, the compressive strength and yield strength of the alloy first decrease and then increase, while the microhardness increases first and then decreases. When the Mo content is 9%, the compressive strength and compressive strain are 1610 MPa and 50.9%, respectively. The self-corrosion current density and R_p value of the tested alloy without Mo addition are the minimum of 33.19 nA·cm^-2, the maximum of 1531.52 kΩ·cm², respectively, and the corrosion resistance is the best.

Key words: Ti alloy, phase structure, microstructure, mechanical properties, corrosion behavior

中图分类号:

TG166.5

张曼雪, 景然, 张雄, 张晴, 吴倩, 刘以柔. 铸态Ti-20Zr-10Nb-xMo合金的微观组织和耐腐蚀性能[J]. 金属热处理, 2022, 47(3): 147-150.

Zhang Manxue, Jing Ran, Zhang Xiong, Zhang Qing, Wu Qian, Liu Yirou. Microstructure and corrosion resistance of as-cast Ti-20Zr-10Nb-xMo alloys[J]. Heat Treatment of Metals, 2022, 47(3): 147-150.

参考文献

[1]赵立臣, 崔春翔, 刘双进, 等. 基于d电子合金设计方法的生物医用新型亚稳β钛合金的设计及性能研究[J]. 稀有金属材料与工程, 2008, 37(1): 108-111.
Zhao Lichen, Cui Chunxiang, Liu Shuangjin, et al. Design and research on properties of new type metastable β-titanium alloys for biomedical applications based on the d-electron alloy design method[J]. Rare Metal Materials and Engineering, 2008, 37(1): 108-111.
[2]杨永建, 孙威, 马秀梅. 生物医用β型钛合金设计研究[J]. 科技创新导报, 2009, 16: 10-12.
Yang Yongjian, Sun Wei, Ma Xiumei. Design of biomedical β-type Ti alloy[J]. Science and Technology Innovation Herald, 2009, 16: 10-12.
[3]于振涛, 余森, 张明华, 等. 外科植入物用新型医用钛合金材料设计、开发与应用现状及进展[J]. 中国材料进展, 2010, 29(12): 34-51.
Yu Zhentao, Yu Sen, Zhang Minghua, et al. Design, development and application of new medical titanium alloy materials for surgical implants[J]. Materials China, 2010, 29(12): 34-51.
[4]梁芳慧. 关节置换植入物用材料临床应用现状及发展趋势[J]. 材料科学与工程学报, 2009, 27(1): 112-117.
Liang Fanghui. Clinical application and development of materials used for joint replacement implants[J]. Journal of Materials Science and Engineering, 2009, 27(1): 112-117.
[5]吴义舟, 郭爱红. 生物医用钛合金发展和研究现状[J]. 材料开发与应用, 2010, 25(2): 81-85.
Wu Yizhou, Guo Aihong. Development and research status of biomedical titanium alloys[J]. Development and Application of Materials, 2010, 25(2): 81-85.
[6]Hao Y L, Li S J, Sun S Y, et al. Effect of Zr and Sn on Young's modulus and super elasticity of Ti-Nb-based alloys[J]. Materials Science and Engineering A, 2006, 441(1/2): 112-118.
[7]戴世娟, 陈锋, 王煜. 新型医用Ti-35Nb-4Sn-6Mo-9Zr和Ti-35Nb-1.3Mo-3.7Zr合金在林格溶液中的电化学腐蚀行为[J]. 稀有金属材料与工程, 2014(S1): 90-95.
Dai Shijuan, Chen Feng, Wang Yu. Electrochemical corrosion behaviors of new biomedical titanium alloys Ti-35Nb-4Sn-6Mo-9Zr and Ti-35Nb-1.3Mo-3.7Zr in Ringer's solution[J]. Rare Metal Materials and Engineering, 2014(S1): 90-95.
[8]于振涛, 余森, 程军, 等. 新型医用钛合金材料的研发和应用现状[J]. 金属学报, 2017, 53(10): 1238-1264.
Yu Zhentao, Yu Sen, Cheng Jun, et al. Development and application of novel biomedical titanium alloy materials[J]. Acta Metalurgica Sinica, 2017, 53(10): 1238-1264.
[9]Geetha M, Mudali U K, Gogia A K, et al. Influence of microstructure and alloying elements on corrosion behavior of Ti-13Nb-13Zr alloy[J]. Corrosion Science, 2004, 46(4): 877-892.
[10]王微, 吴文俊, 王刚, 等. 医用低弹性模量Ti合金的设计与工艺研究[J]. 热加工工艺, 2015, 44(19): 109-112.
Wang Wei, Wu Wenjun, Wang Gang, et al. Design and process study on Ti-alloy with low elastic modulus for medicine[J]. Hot Working Technology, 2015, 44(19): 109-112.
[11]Liu Q, Meng Q K, Guo S, et al. α′ type Ti-Nb-Zr alloys with ultra-low Young's modulus and high strength[J]. Progress in Natural Science: Materials International, 2013, 23: 562-565.
[12]Biesiekierski A, Ping D, Li Y, et al. Extraordinary high strength Ti-Zr-Ta alloys through nanoscaled, dual-cubic spinodal reinforcement[J]. Acta Biomaterialia, 2017, 53: 549-558.
[13]Azarbarmas M, Emamy M, Rassizadehghani J, et al. The influence of beryllium addition on the microstructure and mechanical properties of Al-15%Mg₂Si in-situ metal matrix composite[J]. Materials Science and Engineering A, 2011, 528(28): 8205-8211.
[14]Feng Z H, Jiang X J, Zhou Y K, et al. Influence of beryllium addition on the microstructural evolution and mechanical properties of Zr alloys[J]. Materials and Design, 2015, 65: 890-895.
[15]Koyama M, Lee T, Lee C S, et al. Grain refinement effect on cryogenic tensile ductility in a Fe-Mn-C twinning-induced plasticity steel[J]. Materials and Design, 2013, 49: 234-241.
[16]李旭升, 辛社伟, 毛小南, 等. 钛合金氧化行为研究进展[J]. 钛工业进展, 2014, 31(3): 7-13.
Li Xusheng, Xin Shewei, Mao Xiaonan, et al. Progress in research on oxidation behavior of titanium alloy[J]. Titanium Industry Progress, 2014, 31(3): 7-13.
[17]Meng K, Guo K, Yu Q, et al. Effect of annealing temperature on the microstructure and corrosion behavior of Ti-6Al-3Nb-2Zr-1Mo alloy in hydrochloric acid solution[J]. Corrosion Science, 2021, 183: 109320.
[18]Chui P F, Jing R, Zhang F G, et al. Mechanical properties and corrosion behavior of β-typeTi-Zr-Nb-Mo alloys for biomedical application[J]. Journal of Alloys and Compounds, 2020, 842: 155693.
[19]Mccafferty E. Validation of corrosion rates measured by the Tafel extrapolation method[J]. Corrosion Science, 2005, 47(12): 3202-3215.

铸态Ti-20Zr-10Nb-xMo合金的微观组织和耐腐蚀性能

Microstructure and corrosion resistance of as-cast Ti-20Zr-10Nb-xMo alloys

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	张子延, 陈君, 陈晓亚, 李全安, 刘建鑫. 固溶时效处理对Mg-4Sm-3Gd-0.5Zr合金显微组织和耐蚀性能的影响[J]. 金属热处理, 2022, 47(4): 10-16.
[2]	梁恩溥, 徐乐, 杨勇, 王毛球. 添加Al、Cu对40CrNi3MoV钢组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 17-23.
[3]	祁晓亮, 李岩, 定巍, 赵增武. 含Al中锰TRIP钢原始组织对临界退火后组织与力学性能的影响[J]. 金属热处理, 2022, 47(4): 24-29.
[4]	陈保安, 张静媛, 祝志祥, 韩钰, 潘学东, 张磊, 陈素红. 化学成分对高强Al-Mg-Si合金组织和性能的影响[J]. 金属热处理, 2022, 47(4): 30-38.
[5]	陈连生, 张露友, 田亚强, 杨子旋, 李红斌, 潘红波, 魏英立. 低碳高强舰船用钢的CCT曲线及其组织性能[J]. 金属热处理, 2022, 47(4): 63-68.
[6]	王云龙, 余伟, 张昳, 史佳新, 李明辉. 奥氏体化温度对贝氏体钢等温转变及力学性能的影响[J]. 金属热处理, 2022, 47(4): 80-85.
[7]	骆再斌, 范子泽, 彭振. 轻质高熵合金的研究进展[J]. 金属热处理, 2022, 47(4): 100-107.
[8]	吕杰晟, 宋志刚, 何建国, 丰涵, 郑文杰, 朱玉亮. S32205双相不锈钢冷轧退火组织转变及强塑化机理分析[J]. 金属热处理, 2022, 47(4): 141-145.
[9]	王琪, 吴光亮. 回火温度对1100 MPa级高强钢组织与性能的影响[J]. 金属热处理, 2022, 47(4): 146-150.
[10]	孙凯, 陈研, 杨绍斌. 时效温度对激光选区熔化TC21钛合金微观组织及硬度的影响[J]. 金属热处理, 2022, 47(4): 155-158.
[11]	张骥俊, 邢彦锋, 曹菊勇. 超声振动对CMT电弧增材制造铝合金组织与性能的影响[J]. 金属热处理, 2022, 47(4): 159-164.
[12]	刘文彬, 乔龙阳, 潘新宇, 程格, 李爱娜, 裴新军. 淬火温度对刀剪用M390粉末冶金不锈钢组织和性能的影响[J]. 金属热处理, 2022, 47(4): 189-195.
[13]	王瑞琴, 葛鹏, 廖强, 侯鹏, 刘宇. 固溶冷却方式对短时用高温钛合金板材组织和性能的影响[J]. 金属热处理, 2022, 47(4): 196-198.
[14]	王绍灼, 孟晗, 王芬, 樊海卫, 李燕, 唐超. 改善低氧TC4-LC及重熔TC4钛合金性能的热处理工艺[J]. 金属热处理, 2022, 47(4): 204-207.
[15]	陈强, 陈林芳, 杨明华. 18CrNiMo7-6钢的可控气氛高温渗碳工艺[J]. 金属热处理, 2022, 47(4): 231-239.